Search Documents

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By F. J. Gauthier, R. G. Gray

"The possibilities of expanding the production rate from the Copper Mountain Mine have been examined using computer programs for analysing a complete range of data, beginning with the diamond drill assays and embracing all steps up to the final rates of return.Programs have been developed to calculate the mineralization inventory file, a matrix of blocks containing the grade and the type of mineralization estimated for each block. Given the topography, prices of metals and costs, the pit limits are optimized using a three-dimensional technique. Within the pit, ore reserves at any cutoff can be calculated. Mining of the pit is then simulated using an interactive production scheduling program on a timesharing computer. The annual tonnage and grade figures from the production schedule are input to a financial analysis program, where the present value and the rate of return are calculated at various metal prices. The expansion possibilities can be run through the programs with their respective costs, and evaluated using the rate of return on the marginal cash flow compared to the additional capital expenditure."

Jan 1, 1971

By A. F. Laurin, A. L. Dorr

"Because of its wide areal extent, its numerous lithological facies and its high degree of metamorphism, the Quebec portion of the Grenville province has only partly been explored and prospected. Rock types that are economically among the most interesting in the Grenville are those of mafic and ultramafic compositions, because of their great potential for coppernickel and chromium-platinum. The peculiar mode of occurrence and the distribution of these igneous masses in which copper-nickel mineralization is known to occur indicate' two common geological features: (1) aerial photographs and/or topographic maps strongly' suggest close spatial (and possibly temporal and genetic) association of most of these mineralized mafic and ultramafic intrusions with circular structures; (2) when plotted on a large-scale map comprising the Quebec portion of the Grenville, these circular structures fall along two lines which could correspond to major tectonic features. Even though the genetic links among the mineralized mafic-ultramafic masses, the circular structures and the linear features are not yet fully understood, their associations are believed to be empirically valid and should therefore be used as geological tools by those interested in exploring the Grenville for copper-nickel and possibly chromium-platinum deposits. It should be noted that these mafic and ultramafic bodies do not appear to be spatially related to anorthosite complexes."

Jan 1, 1971

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By C. E. Dowker

"IntroductionMechanization underground at the Buffalo Ankerite mine in Deloro township, Porcupine district, had reached a high level by 1944, both in equipment available, and in the use of this equipment, for all stoping operations. Power feed leyners and the latest type of stopers for drilling, slushers for moving ore and fill, and tugger hoists for all servicing, did much to halt rising stope costs, and in some cases decreased them. On the other hand, little beyond the use of mucking machines and power feed leyners had been adopted in the effort to reduce level development costs, or to increase the advance per man-shift.Faced with ever increasing level development costs, caused by rising prices of equipment and supplies, coupled with increasing wage demands for less physical effort, it was realized that more mechanization of development work was essential. The objectives of such further mechanization were:(1) Decreased development costs(2) Increased footage per man-shift(3) Less physical effort by development crews, with greater take-home pay (4) A more satisfied and stable labour force"

Jan 1, 1950

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015

By James Ball

The paper describes a new type of pump and related apparatus specifically designed to dredge sea-floor minerals from very great depths. The principle of operation of the dredging system is explained, and the factors which determine the equipment size and the power required for varying mining rates and depths of water are discussed. An estimate of the capital and operating cost of a commercial-scale mining system is presented.

Jan 1, 1968

By M. Sugamata

Creep tests were carried out for friction welded joints of AZ31 magnesium alloy rods under an ambient atmosphere at temperatures between 423 and 573K. Tensile tests were also performed at temperature from room to 573K. The obtained results were compared with those of the base metal. AZ31 extruded rods of 19 mm in diameter were joined by brake type friction welding machine. Creep and tensile specimens were machined out of the welded rods. The tensile strength of the joints was almost the same as that of the base metal at room temperature. However, joint efficiencies of welded joints were about 92% at above 373K. The elongation of welded joints was lower than those of base metal. The welded joints showed appreciably higher minimum creep rate and shorter rupture time than the base metal at all the tested temperatures and initial creep stresses. Creep and tensile rupture of the joints always occurred at near the weld interface. Thus, friction welded joints of AZ31 alloy showed lower creep and tensile strength than the base metal at elevated temperature.

Jan 1, 2006

By Jan W. Merks

The objective of metrology in mineral exploration is to derive unbiased confidence limits for masses of metals contained in reserves and resources. Sets of test results for gold and silver determined in pairs of interleaved bulk samples give unbiased confidence limits for the central value of each metal. The same sets of test results show how to verify spatial dependence by applying Fisher?s F-test to the variance of a set and the first variance term of the ordered set. A significant degree of spatial dependence gives a higher degree of precision for the central values of gold and silver. Plotting variance terms of an ordered set against the variance of the set and its lower limits of asymmetric 99% and 95% confidence ranges gives a sampling variogram. Sampling variograms put in plain view where spatial dependence in sampling units or sample spaces dissipates into randomness. The application of statistical methods to test results for sets of ordered core samples within boreholes, and for sets of ordered ore volumes within profiles, plays an important role in defining reserves and resources.

Oct 1, 2009

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By Rosie Moore, Harvey Keats, Kerry Sparkes, A. J. Naldrett

"Abstract-The Voisey’s Bay Ni-Cu-Co deposit was discovered in late 1994 as the result of prospecting initiated in the summer of 1993. By July 1995, proven mineable reserves were 31.7 x 106 tonnes grading 2.83% Ni, 1.68% Cu and 0.12% Co, and current total resources in all categories are quoted to be in the order of 150 X 106 tonnes. The deposit is associated with a body of troctolite belonging to the Nain Anorthosite (1.35 Ga - 1.29 Ga) suite, which was emplaced across the boundary between the Proterozoic "Rae" Province to the west and Archean "Nain" Province to the east.The deposit can be described in terms of three geological settings. The "Ovoid" is a 600 m long by 350 m wide by 100 m deep lens of massive sulfide, covered by 10 m to 20 m of glacial overburden, and separated from the underlying country rock quartz-plagioclase-biotite gneiss by a breccia of gneissic fragments in troctolite known as the Basal Breccia Sequence. To the west of the Ovoid lies the "Western Extension", comprising disseminated and massive sulfides in a north-dipping sheet of troctolite which ranges from upper unmineralized troctolite down through troctolite with increasing amounts of sulfide (up to 50%), to massive sulfide (in some places only), and then to Basal Breccia Sequence. East of the Ovoid, the troctolite sheet broadens out into a troctolite intrusion, within which occurs the "Eastern Deeps", a zone of massive and disseminated sulfide up to 100 m thick that is currently being explored. The mineralization of the Eastern Deeps lies along the line of intersection of a feeder sheet with the base of the intrusion. The current interpretation is that the three geological environments represent different erosional levels through a single mineralized intrusion. In this model, the deepest erosional level lies to the west and exposes the feeder to surface, whereas the Ovoid represents the base of the intrusion at surface, and the Eastern Deeps the base of the intrusion overlain by 600 m to 900 m of troctolite. Sulfides and gneissic fragments were brought up by magma flowing quickly through the feeder, and settled out where the flow rate decreased as the sulfide-bearing magma mixed with magma already emplaced in the intrusive body."

Jan 1, 1996

By P. Diehl, M. David

"As shortage in the supply of mineral commodities become more probable, there is an increasing need for reliable and comparable reserve/resource data. It is therefore necessary to standardize the traditional classification procedure by quantifying the three basic criteria in resource evaluation: economic feasibility, geologic assurance and recovery. For the portion of fairly well documented deposits and as far as their geologic parameters are concerned, geostatistical methods can considerably improve the quality of ore classification. In respect of economic feasibility and recovery, approved geostatistical methods can be introduced directly into the classification procedure. The concept of geologic assurance, however, requires a new interpretation in terms of geostatistical error spread. As the ""risk"" in estimating an ore parameter is also a function of the respective block size, it is reasonable to define not only upper limits for the risk intervals for each class of uncertainty, but also block dimensions which reflect the typical stage of planning associated with the different ore categories. An algorithm has been developed to block out areas inside a mine or a large panel which satisfies the constraints of an ore category in respect of the risk intervals of a parameter and in respect of their size. The method has been computerized and is demonstrated on a massive copper-nickel deposit.IntroductionFacing an uncertain future with respect to the demand and supply of mineral commodities, both governmental authorities and the mining industries show an increasing interest in a useful framework for the assessment and classification of the remaining mineral resources"". This is reflected by the recently published appraisal and classification scheme of the United Nations as well as by the new or revised classification systems of the USA; Canada or Australia. Moreover there are various classification schemes which are currently discussed in major mining companies."

Jan 1, 1982

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013

According to the principle of similarity, the physical and chemical configurations of a system can be defined by ratios of magnitudes within the system and do not de-pend on the size or nature of units of measurement. In the present work, the similarity principle was utilized in evaluating the reducibility of various iron ores in a rotary batch furnace under optimum operating conditions. It was then used successfully to extrapolate the results, first to the operation of a 20-ft. pilot-plant kiln and then to an industrial-size 80-ft. kiln. By means of this systematic analysis of kiln operation, it was possible to increase the production capacity of the kiln considerably. T HE kilns used by the Strategic-Udy process for the partial reduction of iron ores are, in most aspects, similar to conventional calcining kilns. Iron ore is fed continuously in the upper (feed) end of the kiln and, as the latter rotates

Jan 1, 1964

By Leroy G. Hagenbuch

"IntroductionAn integrated Truck Management Information System (Truck MIS) evolves as seemingly separate functions combined to yield a single homogeneous result / product. The concept of a computer integrated Truck MIS includes truck dispatch, truck maintenance management and truck weighing.A truck management system is only as good as the information / data bases input to it. The concept of an integrated system works best with automated data gathering. Automated data gathering provides timely and normally, the most accurate historical information/data bases. Data bases are, however, historical, which is a problem to be overcome in a computerized truck management information system, especially in regards to a truck dispatch system as loading sites / loading conditions and some dump site conditions continually change. As these changes occur, data base s must change as well, and thus the need for the continual update of data bases that the computer uses for a Truck MIS.For a truck dispatch system to achieve reliability / viability, dispatch decisions need to revolve around real time data gathered in an automated way. Integration of all truck management function s through automated data gathering lead s to the best over-all system.An integrated system is a combination of many different factors and is only as good as each factor / building block put in the system. With the proper building blocks, an integrated Truck MIS is very feasible - an MIS System that includes weighing, time and motion study, truck maintenance and maintenance management, as well as truck dispatch.Truck MISAn integrated Truck MIS provides for truck dispatch as the ultimate end result, a truly automated /integrated truck dispatch system (to function non-operator-dependent). The following comprises its central building blocks:-Time.- Haul Cycle Segments.Truck Status, i.e. Load on truck,- being loaded,- loaded,- unloaded,- in service,- out of service.- Vehicle Location.Loading Equipment Status.- in service,- out of service.Optional- distance travelled in each haul segment.With this data provided on a non-operator dependent basis, it is possible to build good data bases so a computer can make truck dispatch decisions. Knowing what information is needed as the central core to a good Truck MIS, how can this information be automatically gathered and fed into a central control computer?"

Jan 1, 1986