Search Documents

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By S. Abu-Samra

By virtue of its complex nature, the construction industry comprises a wide spectrum of interrelated variables and factors. This multifaceted character of the construction industry puts the use of engineering modeling tools and techniques on top of project management necessities. This research introduces a macro-level earthmoving management system using Genetic Algorithms (GAs) to reach the optimum allocation of earthmoving equipment. The Earthmoving Equipment Management System (EEMS) functions through four integrated modules: (1) A Central Database containing information about projects and available equipment; (2) An Equipment per Segment Selection module that calculates the cut and fill quantities, plots the Mass Haul Diagrams, and selects the equipment types to be used for each segment; (3) An Equipment Pool module which determines the production and cost for each available equipment, based upon the project site conditions; and (4) An Optimization Engine equipped with a GA optimization solver. This engine formulates the optimum earthmoving cost for all projects, by changing the number of allocated equipment. The Optimization Engine takes into account the number of available equipment and calculates the weekly equipment allocation. The EEMS model was implemented on an earthmoving company conducting five different projects on hand. The model proved to be an effective tool in providing decision makers with optimum equipment utilization on a multi-project scale to minimize the earthmoving cost. The results were then compared with the company?s existing micro-level management system, demonstrating better performance on the level of savings, amounting to 13% of total earthmoving cost.

Aug 1, 2013

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By M. J. Sapko, R. W. Watson, E. S. Weiss

The relative incerdivity of several blasting agents was evaluated in the Bureau's Bruceton Experimental Mine (BEM) . The minimum charge weights resulting in the ignition of predispersed oil shale dust clouds were measured for each of the explosives. A 400 g unstennned charge of ANFO (ammonium nitrate-fuel oil) was sufficient to initiate an oil shale dust explosion, whereas a 1000 g unstenuned charge of an emulsion blend did not ignite the dust even with the addition of 4% methane gas. Several stenuning materials were evaluated in the BEM for their effectiveness in preventing the ignition of near stoichiometric methane-air mixtures. Water stenuning was superior to all other inhibitors tested against methane. Explosibility testing of fine sulfide ore dust in a 20 L chamber and in the BEM show that the dust is capable of propagating an explosion given nominal concentrations of 700 to 800 g/m3. Results are encouraging and irrlicate that there is merit in pursuing explosive composition as a means of reducing ignition probability of oil shale and sulfide dust clouds generated during nonnal blasting operations. The proper selection of explosives and stenuning materials should significantly reduce the probability of secondacy dust explosions in oil shale and sulfide ore mining.

May 11, 1988

By E. Sigal

Overview ?Intrinsik has completed several wide area HHRA and ERA studies of mining and smelting communities ?Several ?Lessons Learned? ?Key areas related to: ?Study Design ?Data Quality ?Bioaccessibility ?Speciation ?Weight-of-Evidence Approaches ?Advances in Ecological Risk Assessment Techniques

May 1, 2009

By James H. C. Martens

Among the many interesting problems of the pre-Cambrian of the Canadian Shield is that of the origin of certain types of gneisses which are intimately associated with the granites on the one hand and with the metamorphic rocks of known sedimentary origin on the other. The observations recorded in this paper on the structure and composition of these ancient rocks found in a small part of northern Quebec may help to lead to a clearer understanding of the way in which they were formed and also constitute a contribution to the regional geology and petrography of a district for which little detailed information is available. The area considered is located near the Ashuapmuchuan, or Chamuchuan, river about 180 miles north-northwest of the city of Quebec, and therefore well within the Canadian Shield. Although most attention was devoted to the rocks along this river from the 57th to the 70th mile above its entrance into Lake St. John, a few observations on other localities to the north and northwest of that lake will be included. The field work was done in the summer of 1924 in cooperation with L. W. MacNaughton, E. S. Roberts, and B. M. Shaub, all of Cornell University. The party ascended the Ashuapmuchuan river by canoe and spent about a month near the mouth of Stacker, or Brochet, river, the outlet of the lake of the same name, returning by way of Mikoasas river. The writer wishes to express his obligation to his associates for their co-operation in the field and for their permission to publish the results. He is especially indebted to B. M. Shaub for the photographs of rock outcrops. Professor A. C. Gill g:ive many suggestions which were helpful in the laboratory study of specimens and in the preparation of this paper.

Jan 1, 1927

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By L. E. Young

"The Red Dog deposit of the western Brooks Range, Alaska was discovered in the 1970s. Two mineralized areas are present, the Main and Hilltop deposits. With indicated and inferred reserves of 77 million tonnes of 17.1% zinc, 5.0% lead and 82 g/ tonne silver, the Main deposit of Red Dog represents one of the world's largest zinc-lead deposit s. Since serious evaluation by Cominco commenced in 1980, a better understanding of deposit geology has been gained through 10 715m of diamond drilling and concurrent geologic, geophysical and geotechnical studies. The Red Dog deposit is of Mississippian to Pennsylvanian or Early Permian age, and straddles a redox transition in fine-grained and chemical sediments of the Red Dog structural sequence.The Main deposit has been modified by regional Mesozoic thrust faulting and isoclinal folding, resulting in complex interrelationships between silica rock, sulphide rock and barite. Multiple lines of evidence suggest the Main deposit contains both a syngenetic stratiform and a replacement component. Ore fluids were probably derived by regional lateral movement of brines through a coarse clastic footwall aquifer, then upwards along block faults to the site of the Red Dog deposit.Historical PerspectiveThe region in the vicinity of the Red Dog deposit (Fig. 1) was first prospected by J. W. Kelley in the late 1880s (Orth, 1967). The first coordinated inland exploration was conducted by the U.S. Geological Survey in 1910-1911 and 1923-1926 (Smith, 1913; Smith and Mertie, 1930). The earliest reports of zinc-lead mineralization in the region include reference to samples collected at unknown locales by Eskimo prospectors (Anderson, 1944). In 1955 stratiform pyrite was discovered 19 km west of Red Dog by I.L. Tailleur of the U.S. Geological Survey (Tailleur, 1970). The first reported visit to what is known as Red Dog was by I.L. Tailleur in 1968, who was field checking a colour anomaly noted by B. Baker, a local bush pilot (Tailleur, 1970; Moore et al., 1986) ."

Jan 1, 1989

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By Greg Baiden

Telerobotics focused on mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run? A new Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University. This chair will investigate these questions and many more through a series of experiments in a newly established telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian college?s eDome. The laboratory will support many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one/quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments and some preliminary results.

May 1, 2003

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018