Search Documents

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By J. R. Giegerich

Purpose It is the purpose of this paper to describe the application of underground conveyor systems to the transportation of ore in the Sullivan mine of The Consolidated Mining and Smelting Company of "Canada, Limited, at Kimberley, British Columbia. General Applications Conveying has been recognized as a means of underground transportation for a great number of years but only during the past fifteen to twenty years has there been any extended application of the method to underground metal-mine operations. Coal miners became conveyor conscious before metal miners. Probably one reason for this is the fact that there are more flat coal seams than flat orebodies. A second reason is that coal is light and is a less abrasive material than most metallic ores. The vast improvements made in belt construction during the past few years, together with improvements in mechanical conveyor equipment, have gone a long way in making this form of transportation attractive to the metal miner. In new mines being opened today, or in major extensions to older mines, the possibilities of conveyor transportation should receive serious consideration. There may not be any widespread application of the belt conveyor as a replacement for the conventional hoisting and locomotive haulage. Where there is an application, tl1e saving in cost can be appreciable and many operating ad-vantages gained because of ease in operation.

Jan 1, 1951

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By J R. M Hutcheson

Advocate Mines Limited came into initial production on June 30, 1963, with an annual capacity in excess of 60,000 tons of high-quality chrysotile asbestos fihres, thus strengthening Canada's position in world production. The history of this development is traced from discovery through initial exploration, financing, orebody delineation and evaluation, pilot-plant production and product evaluation, construction of the plant, construction of deep?-sea shipping facilities, provision for a closed shipping season, and provision for the remoteness and for the lack of services, through to realization of full production capacity. The many unique aspects of the project are given special attention, particularly in the light of the first year of full-capacity operation. The marketing of the products in a highly competitive world market is reviewed, with special emphasis on product evaluation, quality control and the shipping of high-quality products to consumers throughout the world. C ANADA'S newest asbestos producer, Advocate Mines Limited, is located at the north end of the Burlington Peninsula, White Bay District, Newfound-

Jan 1, 1965

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950

By H. Thomasson

This paper will deal with on-site maintenance welding using the stick electrode, electric arc process. It is primarily concerned with the underlying principles, the application of which, or the lack of such application, governs the success or failure of the operation. It will discuss first the base metal or item to be welded, including the field identification of its weld-ability and the determination of the procedures to be followed. Second, it will outline heat effects and the interrelation between heat applied as part of a welding operation and heat deliberately applied as part of a heat treating cycle, stressing the fact that in welding the same basic principles are effective. The third consideration will be weld metal and its control of both composition and properties. Last, but not least, distortion, shrinkage and residual stress will be considered and practical means for minimizing their adverse effects outlined.

Jan 1, 1967

By Les F. Sawatsky

Surface drainage, particularly mine closure drainage, must be properly considered during all stages of mine planning because it presents constraints that are critical to economic mine operation, minimizing environmental impacts and ensuring compliance with government regulations. Deficient mine site drainage increases costs of operation, causes unnecessary environmental impacts and may result in regulatory violations. The scope of this paper includes stream diversions around mine areas, drainage systems within the mine disturbed footprint, and closure drainage works to control surface water, ground water, erosion, sedimentation, and seepage discharges following mine operations. Developing selfsustaining drainage facilities upon mine closure, requires a mine plan that develops appropriate topography and constructed drainage courses that replace the function of pre-disturbance drainage systems without aggravated erosion and deterioration. Drainage criteria, particularly closure drainage criteria, represent important constraints on mine planning and are best considered by integrating drainage features into the mine plan well in advance of mining activities. Integrated mine planning by a multi-disciplinary team is recommended to achieve closure objectives at minimum cost and maximum effectiveness The geomorphic approach to channel design is an effective means of providing a drainage system that has the appearance, function and longevity of natural systems. By incorporating this technique into closure drainage planning, mine operators can construct sustainable (walk-away) drainage systems that require little or no maintenance in the long-term. This paper presents a process by which drainage criteria and associated mine plan constraints can be integrated into the mine planning process. This paper outlines the process for detailed design of drainage facilities, particularly closure drainage systems that are designed by the geomorphic approach.

May 1, 2009

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972

By F. Chachula, A. Molinaro

"Sulphide mineral flotation operations continuously strive for a balance between mineralogy, mineral liberation, circuit conditions and reagent solutions to maximize the production rate and recovery of payable metals. The Taseko Gibraltar copper – molybdenum mill operations underwent an extensive project focusing on the fundamentals to identify the effects of process conditions and mineral liberation to improve the bulk circuit copper – molybdenum recovery efficiencies in the bulk flotation circuits. This discussion will provide process data that demonstrates; 1) fundamental relationship between mineral liberation to recovery and grade, 2) flotation circuit condition testing and optimization, 3) reagent combinations resulting in efficient/economical mineral recovery, and 4) the development of a xanthate free reagent solution. The data presented and discussed will also touch on flotation parameters including pH, retention time, kinetics and the effect on bulk circuit recovery performance.INTRODUCTION Taseko's is the owner (75%) and operator of the Gibraltar copper-molybdenum mine, located in south-central British Columbia, the second largest open pit copper mine in Canada and the largest employer in the Cariboo region. Taseko restarted Gibraltar in 2004. From 2006 until 2012, the company invested ~$700 million to expand and modernize the operation which was originally scheduled for demolition when the company acquired it in 1999. In the spring of 2011, construction commenced for Gibraltar Development Plan 3 (GDP3). GDP3 included the construction of a standalone 30,000 ton per day concentrator, built adjacent to the existing 55,000 ton per day facility. The new design capacity of Gibraltar was designed to be 85,000 tons per day. An integral part of the project was a new molybdenum recovery facility. In addition to the new concentrator, the mining fleet was upgraded with a new mining shovel, production drill and ten haul trucks (Taseko, May 2015). In May of 2015, the Company completed an updated mine plan for Gibraltar featuring a 50% decrease in strip ratio. This new mine plan was a result of a detailed, six-month engineering study and forms the basis of an updated NI 43-101 compliant reserve (Taseko Announces Improved Economics At Its Gibraltar Copper Mine, 2015). The new mine plan took into account lower milling costs as a result of the modernized processing facilities (Taseko, May 2015)."

Jan 1, 2018

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By Paul Hughes

Purpose of Research ? What are the loading mechanics of paste against barricades? ? What is the capacity of the composite paste fill fences? ? Based on the loading mechanics of the paste, do the fill fences pose a risk of failure? Outline ? Glossary of Terms ? General Introduction ? Research Methodology ? Site Description ? Instrumentation Program ? Results ? Analysis ? Conclusions ? Recommendation for Future Work

May 1, 2008

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950