Search Documents

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By Abu Syed H. Kabir, Mehdi Sanjari, Steve Yue, Jing Su, In-ho Jung

AZ31 magnesium alloy sheets were produced by high speed rolling (HSR) at 1000 m/min at a low temperature of 100 ?. A high reduction of 72% can be achieved in single pass. At the reduction of 30%, the microstructure was covered by shear bands and twins. When the reduction was increased to 49%, dynamic recrystallization (DRX) was clearly observed in the vicinity of shear bands and twins and the full recrystallization was seen at a reduction of 72%. In order to study the static recrystallization (SRX) behavior on the heavily twinned structure, annealing was then carried out at 200 ? on the as-rolled specimens at the reduction of 30% for different times. Static recrystallized grains were also firstly observed on shear bands and twins after 45 s and the microstructure was mostly fully recrystallized after 1 h annealing with a few retained large elongated un-recrystallized grains. Texture weakening was found during annealing on the heavily twinned specimens by SRX, but not during high speed rolling by DRX. In the present study, effect of DRX and SRX on microstructure and texture evolutions during rolling and annealing were compared.

Jan 1, 2015

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

By L. Kilburn

A survey of 281 mineral exploration agreements examines the ratios among three ways that may be used to purchase an interest in a mineral property, viz: pay cash, pay shams and make future expenditures on the property. The dollar value of the future expenditures exceeds that of cash or shams by about nine times in most of the 110 agreements that contain cash-expenditure or share-expenditure components. Results suggest that cash and shams are treated about the same in terms of value. Buyers and sellers haw opposing priorities for the way that they prefer to purchase a mineral property. These opposing priorities should give rise to a perceived 50:50 balance between cash/share payment and future expenditures to satisfy the idealized situation described by most definitions of fair market value (FMV). This balance between cash/share payments and future expenditures appears to be rationalized in negotiations to a FMV when expenditures are nine times greater than cash and/or payments. On this basis, it is proposed that the FMV of a property may be determined by aggregating the dollar amount of the cash/share payments plus one-ninth the dollar value of future expenditures, as set forth in the respective purchase agreement, and proportionately applying such aggregate to full property value.

Nov 1, 2005

By R. K. Borden

Rio Tinto is committed to proactive mineral waste and acid rock drainage management. Corporate requirements are closely aligned with the GARD Guide principles of early geochemical characterization and prediction followed by selection and implementation of management strategies to prevent or minimize ARD. Each operation is required to design and implement an ARD and Mineral Waste Management Plan. Successful implementation of the plan requires commitment at all levels of the company, from senior management, to geologists, mine planners, environmental staff and equipment operators. Examples of the successful integration of ARD management strategies into mine operations are cited from several mines.

Jan 1, 2011

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019

By Jos. Kalbhenn

MR. G. G. BOWSER: Mr. Kalbhenn's paper is an excellent one and is a concise description of a very interesting piece of work. It is well known that a great deal of preliminary study was given to this job before the final plans were made. It is due to this thorough preparation .chat the work progressed so satisfactorily, smoothly, and safely. The ideas carried out in the construction of the hardwood pack, timbered compartment, inclined raise, loading chute, and steel-boomed room, all contributed to a successful conclusion of the work. The extra care in being certain that the compartment shafts were well timbered was especially necessary on account of the difficult blasting conditions. In other words, the foundations .of this job were well and truly laid. The blasting in this work was very difficult due to the nature of the Strata. Working under an ever precarious roof condition and completing .this job with only two lost-time accidents is a record of which to be proud. The shaft men engaged on this work are also due for praise. I regret I did not visit this work while it was in progress. It was not in lack of interest. This, however, more or less proves that the blasting end .of this job went along with practically no trouble. I have seen the nature of the rock, as I made several visits to the tunnels while they were being put through from the Phalen to the Harbour seam. According to figures in Mr. Kalbhenn's paper, the explosives consumption works out to 1.61 pounds per cubic yard of rock in the solid, or 0.8 pounds per ton. The explosives consumption in the tunnels ran from 2.86 to 3.46 pounds per cubic yard or an average of 1.58 pounds per ton of rock. Of course, the rock in the shaft was blasted in the most economical way possible, as far as powder costs are concerned, as the face advanced at close -wright angles to the strata and gravity was acting with the explosive. The tunnels were driven nearly 'end on' the strata and bottom holes had to be lifted, and I believe there was some re-drilling of ribs left in the floor. I would like to congratulate Mr. Kalbhenn on his very fine paper.

Jan 1, 1944

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By D. P. R. Smyth

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive ?Mine-to-Mill? Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

By W. W. Bake

INTRODUCTION IN IN JUNE, 1943, the main pillars of the Beattie Mine glory hole failed, allowing over a million yards of wet clay and debris to flow into the mine, completely filling all workings to within seventy feet of the 3rd level. The resulting Job of clearing these workings and rehabilitating the mine represents a unique and hazardous operation, seldom, if ever, previously encountered in Canadian mining. The purpose of this paper is to describe one phase of this operation -that of cleaning and rehabilitating the mine from the 6th to the 9th level -to outline briefly the events which led up to this work and to describe the techniques and costs involved. It will be noted that such costs, methods, and performance figures as are dealt with in this paper refer only to work in the internal shaft and adjoining workings from the 6th to the 9th level, previous work having been done under other supervision and management. The Beattie mine is in Duparquet township, northwestern Quebec, twenty miles northwest of the town of Noranda and twenty-three miles southeast of the town of La Sarre. The mine and the town of Duparquet, which it?supports, are accessible by highway from Noranda throughout the year. Production at the Beattie mine began in May, 1933, and up to June, 1943, twenty-one million dollars in gold and silver had been recovered from five and a half million tons of ore.

Jan 1, 1951

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By Robert M. Vadas

Special considerations are described as they apply to the design of ring gears for high-power grinding mills. AGMA requirements, the importance of the supporting structure, material selection and related field experience are discussed, with special emphasis on available and developing manufacturing technologies.

Jan 1, 1978