Search Documents

By S. Espley, G. Tan

"Inco's Little Stobie Mine is a low-grade nickel operation producing approximately 4()()() tons per day. Backfill has never been an economical option at the mine; therefore, the only viable type of mining in the upper zones has been by sub-level cave. This mining method allows for the draw-down of a rock cover into the empty stopes to provide stability to the over-all rock mass. In the lower areas of the mine, bulk blasthole mining methods have taken place, without rock fill, resulting in extremely large open stopes. As the mine reaches its final stage of recovery, it is inevitable that the hangingwall of the large voids will undergo tensile failure via spoiling.This paper deals with the collaborating efforts of Inco's Rock Mechanics group and the Little Stobie mining operations toward the successful recovery of the ore zone remnants such that the inevitable failure, and time of failure, of the rock mass is ""controlled"". Within the mining scheme, several key requirements had to be met to satisfy the operations: (1) production rates; (2) good blast fragmentation; and (3) secure pulling-horizons. A full-scale rock mechanics study was carried out involving: numerical modelling studies; pulling ellipse analyses; blast design, monitoring and analyses; laser profiling; and time domain rej7ectometry (TDR) instrumentation. The final recovery scheme, employing a controlled failure, involves recommendations on: (1) blasting techniques; (2) support systems; (3) mining sequences and scenarios; and (4) monitoring systems."

Jan 1, 1994

By F. C. Lendrum

Introduction The property of Normetal Mining Corporation is in Desmeloizes township, Quebec, twelve miles north of Dupuy on the main line of the Canadian National railway from Quebec city co Cochrane, Ontario. The ore bodies occur within a band of highly sheared and sericitized agglomerate which strikes N.60°W. and clips 82° north. Along a zone 1,000 feet or more in length and of variable width, the agglomerate has been replaced by copper, zinc, and iron sulphides, with copper usually predominant on the hanging-wall side and pyrite replaced in part by sphalerite on the footwall. A northsouth diabase dyke cuts through the ore zone near its east end. The Normetal mill produces a copper concentrate and a zinc concentrate which are shipped, respectively, to Noranda, Que., and Newcastle, Penn., U.S.A., for further treatment. The present paper deals with the milling of ore from what is known as No. 3 orebody. This is a lenticular body of high-zinc ore lying co the east of the diabase dyke, along the line of strike of the main ore zone, which extends westward from the dyke. On its northern side, No. 3 orebody is in contact along most of its length with a narrow band of copper ore which is highly oxidized.

Jan 1, 1948

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By D. Mas Ivars, K. Suzuki, J. A. Vallejos

"A comprehensive geotechnical characterization has been undertaken at the El Teniente mine to describe and determine the rock mass behaviour strength properties of the primary copper ore. The Synthetic Rock Mass (SRM) modelling approach is used to simulate the mechanical behaviour of this heavily and unfractured rock mass. The micro-parameters of the model have been calibrated against mechanical properties and scaling laws for intact rock and veins, in order to represent virtual samples of four different geotechnical units. Results can be used to predict the rock mass scale effects, anisotropy, and brittleness properties that cannot be obtained using empirical methods.INTRODUCTIONThe primary copper ore at the El Teniente mine is described as very competent and massive, given that it exhibits a brittle behaviour (Rojas, Cavieres, Dunlop, & Gaete, 2000). This description is coherent with the geological description of the rock mass, which does not have discontinuities match as the definition provided by International Society of Rock Mechanics (ISRM, 1981). Only faults can be classified as discontinuities, but they are widely spaced. The primary copper ore has a high frequency of veins, where the cooper mineralization is hosted, these vein network structures are known as stockwork. Soft veins containing weak minerals as infill (chalcopyrite and anhydrite) control the disassembling of the rock mass during caving (Brzovic & Villaescusa, 2007).Presently, there are mainly two traditional methods used to estimate the strength of the rock mass: 1) determination of the strength envelope of the rock mass using scaling parameters from laboratory tests and 2) using numerical modelling based on back analysis of previous experiences of failure observed and measured in mining or civil excavations. The primary copper ore of El Teniente mine has no fractures; therefore, it is difficult to determine a rating that would enable to scale laboratory data, such as, RMR (Laubscher, 1977) or GSI (Hoek, 1994). This is the reason why the first option is not valid unless the entry data is manipulated or adjusted in order to obtain reasonable results. The second option requires, in general, a good characterization of a previous failure event in the rock mass, which is not always available. In recent years, new techniques of numerical modeling have been developed (PFC3D, ELFEN, Abaqus). Those methodologies are the third way to estimate the strength of the rock mass, but they are still in development. Particularly, the concept of SRM developed by Itasca is implemented in this study (Pierce, Mas Ivars, Cundall, & Potyondy, 2007; Mas Ivars et al., 2011), aiming to capture the real behaviour of the rock mass."

Jan 1, 2015

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By R. B. Nourse, R. Hundermark, B. Masters, H. Joubert

The new 30 MVA slag cleaning furnace at Waterval Smelter, Rustenburg Platinum, South Africa, has been in operation since 10 March 2003. The furnace design and operation face a number of challenges including a wide variety of feed materials and resulting bath conditions. Furnace feed varies in combinations of granulated Waterval Ausmelt Converter Slag (WACS), hot fed Peirce-Smith converter slag, concentrate and reverts. Coke is added as reductant. The resulting slag composition varies considerably and regularly. For the case feeding WACS an almost pure fayalitic slag (60%+ FeO, 30%+ SiO2) with a very low viscosity results. Due to the widely varying slag conditions, including a superheated fayalitic slag with high fluidity, a robust sidewall design is required adjacent to the slag bath. For this reason the furnace sidewall is equipped with Pyromet's MAXICOOL® high intensity copper cooling system. The design and installation of the copper coolers as well as tap holes are discussed. To cope with the variation in bath conditions and high slag superheat (350°C when tapped at 1650°C), the copper coolers are capable of removing peak sidewall heat fluxes above 500 kW/m2. Feedback is included on the performance of the Pyromet MAXICOO® copper cooling system for the first two years of operation. The paper further includes an overview on the design and performance of the tap holes, furnace shell, furnace roof and copper slag spouts.

Jan 1, 2005

By B. A. Zaharov, J. M. Shneerson, L. V. Chugaev, M. T. Zhunusov, A. M. Markelov, S. V. Drozdov

The main direction of research was the application of autoclave technology for the flotation concentrates or biooxidation feedstocks. The industry modernization also expects the possibility of increasing the yield of the flotation concentrate, to allow an increase in gold extraction in flotation circuit. This paper provides brief description of results obtained for concentrates with the yield of 4 and 8%, as well as corresponding biooxidation feedstocks. Technological efficiency of autoclave oxidation is shown for both concentrates and biooxidation feedstocks. The process has been evaluated on a laboratory and a continuous pilot plant scale. Gold extractions from POX discharge are ranging from 94-97% for each product, with only 5-7 kg/t cyanide consumed.

Jan 1, 2014

By P. K. Kaiser, S. M. Maloney, S. P. Singh

"Corrosion of underground support measures constitutes a concern to industry in both safety and economic terms. It also represents a potential market for corrosion resistant materials such as stainless steel.In order to assess the market potential for a stainless steel friction rock bolt, a review of current corrosion processes and remedial or preventative measures in the underground environment was undertaken. This was supplemented by distribution to industry of a detailed questionnaire, concerning the magnitude and extent of support corrosion and the costs of current support measures, and by visits to selected sites. Following data synthesis, support costs were established and the economic benefit of stainless steel rock bolts evaluated.Stainless steel rock bolts can be an effective cost reducing measure in unscreened areas requiring frequent reconditioning. Their benefit is rapidly diminished, however, if only partial reconditioning is required, the reconditioning interval is long or if screening is required.While most industry personnel are receptive to the application of stainless steel support measures, the localization of corrosion problems and the potential high cost of this type of support are barriers to its widespread implementation. They have potential for use in extreme environments. However, this relatively small market may not be economically viable.IntroductionFriction rock bolts are the simplest of all interior rock fixtures. The friction resistance to sliding of the rock on the bolt is generated by a radial pressure against the borehole wall over the length of the bolt. Two types of friction rock bolts are currently marketed, the Split Set and the Swellex.Unlike conventional point anchor bolts, friction rock stabilizers may move relative to the rock strata and maintain their capacity even if rock shifts, a condition that sometimes loosens or breaks conventional bolts. Ease of installation, effectiveness in jointed as well as weaker rock, and the possibility of having relatively long bolts are a few of the many advantages which generate considerable interest in the application of friction rock bolts (Wijk and Skogberg, 1982). However, due to their thin-walled construction and large surface area, frictional rock stabilizers are more susceptible than conventional bolts to damage by corrosion. For this reason, they are normally not recommended for long-term use (Jolly and Neumeier, 1987).In light of the above discussion; the Nickel Development Institute commissioned a study by the Geomechanics Research Centre with the objective of generating a credible database for the assessment of the feasibility of a stainless steel friction bolt system in corrosive ground and mine environments."

Jan 1, 1990

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By G. D. Just

"Extensive mechanization of underground mining operations, improvements in blasting technology and the development of simulation models for systems evaluation has now made it feasible to optimize rock fragmentation and materials handling operations. Methods of achieving these objectives are described in this paper, with particular emphasis on the need to obtain precise field data measurements. Techniques are illustrated with reference to the sub-level open stoping system of mine production. IntroductionThe primary objective to be achieved in any mining system is to deliver a specified grade of ore to the mineral processing plant at a planned delivery rate and at the minimum total mining cost. Design and management of such a system is complicated by the large number of unit operations and the often unknown inter- relationships between the different unit processes. This particularly applies in underground mines, where planning restrictions and unit costs are much greater than in comparable tonnage sur face mining operations. These difficulties can often be resolved by the application of judgment based on extensive experience, but the costly trial -and-error methods required for new technology discourage innovation.Most modern medium- and large-scale mines are now extensively mechanized. Consequently, the performance of each unit operation by individual items of equipment should be predictable for a given set of conditions. An essential prerequisite is that quantitative performance data are available from field measurements. Such information can then be used to optimize the design and management of the complete mining system to achieve the minimum tot al mining cost. One of the most significant factors influencing all unit costs is the degree of rock fragmentation. The importance of this variable is indicated by the fact that opt imization of rock fragmentation implies minimization of tot al mining system costs."

Jan 1, 1980

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By H. H. Fairfield

THE production and inspection of the materials of war involves thousands of observations. Logical action is generally based on the interpretation of many observations. The success of such action depends upon the accuracy of the observations and the soundness of the interpretation placed upon them. There are countless instances where the observer 'sees but perceives not'; that is, the significance of a group of observations is lost, due either to faulty interpretation or to no interpretation at all being placed on the results. This condition is being partly corrected in the United Kingdom and the United States (1) by the promotion of certain principles by Ordnance officials. The term Quality Control has been adopted to describe a system of studying and controlling industrial products by methods of handling observations. In these pages an attempt is made to outline in a non-technical manner some of the ideas used in the handling of observations. Of course the authenticity of the observations determines the worth of any decisions based on them. No matter how brilliant is the theory built on unreliable sampling, it is usually of little practical value. n some fields it is almost impossible to obtain observations free from bias. Let us suppose that observers of speed in miles per hour were available for judgment: (a) a bystander, (b) a motorcycle policeman, and (c) a motorist accused of speeding. The bystander might be unbiased but probably would be very inaccurate. The motorist is usually biased on the low side. The policeman is the only qualified observer and, if over-zealous, he might be biased on the high side. Conclusions drawn from large numbers of biased observations naturally would be of little value.

Jan 1, 1943

By Z. Luo, China University of Mining & Technology, C. Duan

"The magnetic separation removal rate of pyrite could be improved effectively by increasing the susceptibility of pyrite. The electromagnetic characteristics and absorption response performance of high-sulfur fine coal were studied in strengthening the susceptibility of pyrite. In the process of treating the sample through the microwave, electromagnetic energy could be converted into heat energy due to dielectric loss and magnetic loss. The RL(dB) was evaluate the performance of absorption response of coal. The microwave improved the susceptibility was in ultra-high frequency region, which is the most natural resonance. The absorption fine coal to microwave was strengthened and microwave energy was improved by adding the magnetite powder with double loss characteristics as the microwave absorber. The dielectric properties and permeability characteristics of the fine coal trend were investigated by maxing magnetite powder. The microwave absorption in different coal thickness was surveyed through the reflection of energy loss.INTRODUCTIONMicrowave desulfurization is one of the most important research directions (Haque, 1999; Makul, Rattanadecho, & Agrawal, 2014; Su, Tang, Zhang, Jing, & Bai, 2014). The working principle of microwave absorption response can be briefly described as the interaction of the sample with microwave energy, which will result in the microwave energy converting into heat energy loss (Keangin & Rattanadecho, 2013). For specific samples, the polarization effect includes multiple polarization mechanisms(Meikap, Purohit, & Mahadevan, 2005). Different polarization mechanisms have different occurrence time and dominant mechanisms. Meantime, energy consumption will be occurred during the process of polarization effect (Chelgani & Jorjani, 2011; Rowson & Rice, 1990) . The absorption of microwave energy in the fine coal is a process of electromagnetic response (Znamenácková, Lovás, Mockovciaková, Jakabský, & Briancin, 2005). Microwave transfers the electromagnetic waves into the heat energy by microwave dielectric loss and magnetic loss for achieving the absorption of microwave energy in the treatment of samples (Lee, Kim, Kim, Chung, & Kim, 2004). The additive magnetic medium is Fe3O4 belonging to microwave energy absorber of double loss medium (Uslu, Atalay, & Arol, 2003)."

Jan 1, 2016

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: 'Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father's home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers' Delight, 16 miles northwest of Baltimore. Thus far, Tyson's observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By M. D. Vance, G. R. Corbett, S. D. Butt

Surface wave imaging is a relatively new seismic technique that generates subsurface depth images without having to drill boreholes into the ground, and is rapidly becoming a standard tool in non-destructive geotechnical characterization. This paper presents a case study of the application of these surface wave techniques to image shallow abandoned mine workings at the Montague Gold Mines district near Dartmouth, Nova Scotia. This district has numerous steeply dipping narrow vein workings from historical mining activity, and has actively subsiding and collapsing crown pillars. Due to the rugged conditions at the site and the relative narrowness of the openings (often less than 1 m), a surface seismic system was developed that had improved portability and lateral resolution over other available seismic imaging systems. Seismic surveys were conducted over two sites where independent evidence indicated the presence of shallow mine workings. At one site, a comparative gravity survey was also conducted. The seismic data was processed to generate velocity vs depth images. Overall, the velocity images show vertical zones of zero velocity in the same lateral positions where historical mapping, current subsidence and gravity surveys indicate the presence of steeply dipping workings. Further, the velocity sections are consistent with the thickness of the till cover at each site and the possible weakening of crown pillars at one of the sites.

Jan 1, 2005

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002