Search Documents

By Milton C. Graves, Marcos Zentilli

"Gold has been reported from most geological environments in Nova Scotia; however, virtually all production (circa 2,000, 000 troy ounces; circa 60 tonnes) has come from that part of the province to the south of the Glooscap Fault which is underlain by Lower Paleozoic rocks of the Meguma Group. Over fifty concordant sets of quartz-carbonate-arsenopyrite veins have seen production. The host rocks are greenschist-grade equivalents of Cambro-Ordovician flyschoid quartz wackes and shales folded and metamorphosed during the Devonian Acadian Orogeny. The veins were emplaced under conditions of greenschist-grade regional metamorphism and under the same conditions of tectonic stress that later resulted in the regional folds and penetrative, axial-plane slaty cleavage. Rapid filling of hydraulic fractures caused by excess metamorphic pore fluid pressure under Acadian tectonic stress conditions can account for the geometry and paragenesis of these veins.The ultimate source for gold deposits in most greenschist-grade domains remains in doubt, but these domains seem to have had ample gold within them available for mobilization. The work done, to date, on the gold geology of Nova Scotia suggests that regional greenschist metamorphism was an effective mobilizer and a potential concentrator of Au, As, W, Fe and S from these vast reservoirs.In rocks of pre-Acadian age north of the Glooscap Fault, gold occurs as an important accessory in volcanogenic massive sulphide ore, as a minor constituent in other types of basemetal concentrations and in one small concordant group of quartz veins.The post-Acadian metallogenetic domain, which overlies and overprints the two older domains, contains small amounts of gold in many mineralizing environments. Veins, with stibnite and gold, cross-cut crystalline rocks. Disseminated gold is present in basal conglomerates of post-tectonic molasse. Gold has been a by-product of Mississippi Valley-type Pb-Zn-Ba-Sr deposits in Lower Carboniferous sedimentary rocks and has been reported with Pb-Zn-Ba-F in veins which cross-cut Lower Carboniferous and older rocks. Small post-glacial placers have also seen minor production."

Jan 1, 1982

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By G. L. Palmer

"Abstract- ln 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with garnet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess mineability and to provide material for metallurgical testing in a pilot plant located at the site. Ilmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay . Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By R. A. Bergman

"Process descriptions are provided for the following ten plants that treat high-magnesia lateritic nickel ores (saprolite) by pyrometallurgical means: PT Aneka Tambang; Cerro Matoso S.A.; Falconbridge Dominicana C. por A.; Hyuga Smelting Company Ltd.; Larco (Societé Minière & Métallurgique de Larymna); Loma de Niquel; Le Nickel, SLN-Eramet; Nippon Yakin Kogyo Company Ltd.; Pacific Metals Company Ltd.; and PT Inco Indonesia.Flowsheets, equipment information,chemistry and production data have been compiledfor plants based on both information providedby the companies and on calculated massand energy balances.IntroductionNickel is of vital importance to modern society. Without it, we would not be able to enjoy many of the things that we take for granted, such as computers, airplanes and stainless steel appliances in our homes and workplaces, to mention a few.Nickel occurs in nature both as sulphide and oxide ores. Approximately 36% of the nickel reserves in the Western World occur as sulphide and 64% as oxide ores. Sulphide ores respond to concentration processes, whereas, oxide ores do not. Sulphide ores mined at 1% nickel can be readily concentrated to 10% nickel, whereas, oxide ores cannot be concentrated and therefore have to be processed as mined.Laterite ores are normally classified intotwo groups:1. The high-magnesia ores, saprolites or serpentines, are, as a rule, processed by smelting. The main reason for this is that the nickel replaces magnesium in the magnesium-silicate lattice. To be able to recover nickel, the lattice has to be destroyed. This can be achieved by smelting under reducing conditions.Acid leaching is also possible, but in this case, large amounts of MgSO4 or MgCl2 will be produced making it costly to regenerate the acid.2. The high-iron, low-magnesia ores are known as limonite. The nickel is relatively loosely bonded to goethite and hence can be recovered by selective reduction followed by ammonium-ammonium carbonate leaching. In recently developed processes, these ores are also being extracted by acid pressure leaching, with high Ni and Co recoveries.This paper focusses on the production of ferronickel and nickel matte from the highmagnesia ores."

Jan 1, 2003

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By Anand Raman, Steve Dixon

"Industry practice for defining acid consumption is based on column tests. Freeport-McMoRan (FCX) has adopted a practice of leach operation using a defined pH or gpl acid in the raffinate based on the column test program. The acid consumption can be easily calculated using the leach operating parameters of SX-EW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate. The column leach test results and a column to heap efficiency factor are used to define the copper extraction. The maximum acid consumption will occur when zero acid is contained in the raffinate. The term Net Extracted Value (NEV) is to define the maximum extracted value relative to acid consumed.This paper presents the operating logic and method used to calculate acid consumption based on column tests and operating parameters.INTRODUCTIONIndustry practice for defining acid consumption is based on column tests. This may result in lower economic value if the tests are not designed to account for operating variables. A test program is described to assist in defining lift height and the influence of gangue on solution chemistry. A simple spreadsheet is presented that will use the leach operating parameters of SXEW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate to calculate the acid consumption for a proposed operation.A review of current leach operations solution chemistry will help to define acid consumption. This is recommended for all current leach operations.DISCUSSIONThe current practice at Freeport-McMoRan (FCX) is the use of column test results to define operating parameters. The monitoring of operational solution chemistry and copper production addresses any changes needed in operational parameters. This practice maximizes the value extracted from each tonne of ore leached."

Jan 1, 2008

By Martin Stoklossa

Surface mining operations typically require run-of-mine material to be sized for further processing. In-pit crushing facilities serve this need, as stationary, semi-mobile or fully mobile units. Although in particular fully mobile crushing facilities have been in use for over half of a century, other surface mining techniques have typically been implemented. However, with increasing operating costs in truck and shovel operations, and other economic considerations, mobile crushing plants are increasingly a viable option. The operational and economical parameters in relation to the optimal surface mining equipment selection will be reviewed. The role of the mobile crushing technology within the continuous vs. noncontinuous surface mining operation and basis for mine planning are also discussed. Current applications and respective case studies will be reviewed. Key performance indicators will be presented. These performance parameters can be viewed as a tool to aid in the equipment selection process. The future direction for further research and development in mobile crushing facilities will also be presented.

May 1, 2008

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011

By David Evans, David Barnes, Robert Raponi

"The Williams Mine processes, on average, 6,450 t/d of gold bearing ore using two parallel grinding circuits, leaching and C.1.P., carbon stripping, electrowinning and refining. At present, each grinding circuit consists of a SAG mill in closed circuit with a spiral classifier and a ball mill in closed circuit with two stages of cyclones.Since grinding has always constituted the largest portion of milling costs, the Williams Mine has been proactive in trying to reduce such costs through innovative changes. One project under consideration is the replacement of one spiral classifier by a vibrating screen.This paper discusses the testwork performed to evaluate the replacement of one spiral classifier by a vibrating screen, and the preliminary engineering performed to date.IntroductionThe Williams Mine, located in northwestern Ontario, approximately 40 kilometres east of Marathon, is part of the Hernia gold camp. The mine is operated by the Williams Operating Corporation and is owned by the Teck Corporation and Homestake Canada Incorporated. Operation of the mine started in October 1985 at a rate of 3,000 t/d. After a mill expansion in August 1988, throughput increased to 6,000 t/d. Production has increased steadily since the mill expansion and in 1995, an average of 6,450 t/d of ore was processed at a recovery of 95.1 %."

Jan 1, 1997

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By K. D. Mills, R. G. Robins, C. G. Anderson, L. G. Twidwell

Arsenic is a metalloid which has attracted great environmental scrutiny in recent decades. Moreover, its control and deportment is becoming increasingly important in the metallurgical processing of modern complex ores and concentrates. As such the authors of this publication have a combined professional experience of well over 100 years in the study and hydrometallurgical treatment of arsenic. Hence, this paper will cover arsenic fundamentals along with a review of technology for removal, fixation and stabilization. Finally, an application of industrial Alkaline Sulfide Leaching (ASL) of a copper enargite concentrate will be elucidated.

Jan 1, 2014

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985