Search Documents

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By Kevin O?Callaghan

Applying Legal Concepts - The Crown must consult, and where necessary accommodate, when: - Crown has knowledge, real or constructive, of the potential existence of Aboriginal rights or title and contemplates conduct that might adversely affect it - Duty to consult is triggered at a low threshold - How much consultation necessary? - Proportional to the strength of claim and potential impact - Spectrum: notice to direct involvement in decision making - Not duty to agree or to get consent (no veto) - Reciprocal: Duty requires good faith and sincere engagement on both sides Role of Proponents: Crown may delegate procedural aspects of its legal duty

May 1, 2010

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By Martin Murenbeeld

Outlook: Nine Bullish Arguments 1. Global fiscal and monetary reflation: PIIGS, US, etc. 2. Global imbalances: the dollar must decline 3. Global FX reserves are ?excessive?: diversification 4. Central bank attitudes to gold: now positive 5. Gold is not in a bubble: room to rise 6. Mine supply is flat: ?peak? gold? 7. Investment demand: long-run uptrend 8. Commodity price cycle: many years to run 9. Geopolitical environment: positive

May 1, 2010

By S. Makni, S. Koppalkar, A. Bouajila

ABSTRACT This paper briefly reviews the gravity recovery between conventional and centrifugal gravity separators. The advantages of semicontinuous gravity separators will be discussed, as will techniques for upgrading the gravity concentrates. The research efforts in optimizing semicontinuous gravity separators will be recalled. An innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. Ongoing gold gravity research has revealed that gold particle shape transformation is one of the main factors explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving plant gravity recovery will be discussed.

Jan 1, 2013

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By G. H. McKay

AT the Eagle mine, near Gilman, Colorado, where the Empire Zinc Company have installed an underground mill, transportation problems were comparatively simple. A railway siding on the Denver and Rio Grande railway is equipped with an unloading dock or platform at the portal of their service incline adit to the mill. This 18-degree incline is approximately 600 feet long from the unloading track to the head of the mill skipway. For the Big Missouri mill, upwards of 2,500 tons of material and equipment had to be trucked from tidewater at Stewart, B.C., a distance of 21 miles to the Big Missouri camp at elevation 2,800. From that point, this freight had to be moved either over or through the Big Missouri ridge, rising to elevation 3,450, to its final location 800 feet from the surface between elevations 2,150 and 2,350. Immediately after leaving the government dock at Stewart, the road crosses the International boundary line into Hyder, Alaska, and then follows a water grade for eleven miles along the lower stretches of the Salmon river. leaving the river, the road climbs for two miles before crossing back into British Columbia territory at Silver Heights, and then continues for another mile and a half to where the Big Missouri road branches off from the main road to the Premier mine. For a distance of four miles from the junction of the roads, the Missouri road is very narrow, with many sharp curves and with irregular up and down pitches and grades up to 25 per cent until it reaches the Summit. From there on, a fairly easy grade leads a mile and a half to the end of the road on Joker Plats. In winter, the last stretch of road is subject to heavy snow drifting, especially through a narrow funnel-shaped gulch, known as 'The Gap', where the snow may pile up to a depth of over twenty feet.

Jan 1, 1938

By A. Rajan

"Drawing upon the experiences of a gold extraction plant startup in the Southern Pacific, this paper will describe the importance of the commissioning phases to the project outcomes to achieve early target production despite an overall time compression to attain full plant production. Some of the highlights of the paper include: impact of roles played by the Owner’s construction and operations representatives during project commissioning, the formation of a capable and competent “Mod Squad,” availability of trained operating personnel, control over work priorities and the scope of work needed to bring the plant to safe initial operations. The commissioning team comprised subject matter experts skilled in process technology supported by “generalists” thoroughly conversant in overall plant operations. The merits of a structured team approach to brainstorm and resolve commissioning challenges as opposed to direction from individual subject matter experts is discussed. IntroductionStartup or commissioning is a unique period in the life of a project. Each stage of a project-exploration, feasibility, design, construction, commissioning, initial operations and continuing operations-requires special talents, know-how, and practices. Each stage makes particular demands of the people involved. Initial operations are no exception.Having experienced the 1997 startup phases of oxide and sulfide facilities for a gold extraction plant at a remote island in the Southern Pacific, I can attest to the many challenges and rewards. Commissioning for both facilities was extremely successful and brought the entire project on line well ahead of the targeted completion dates. Using this specific project as an example, this paper will highlight some of the key features of project commissioning. In this paper, the term “pre-commissioning” denotes all activities that lead to mechanical completion; “commissioning” occurs when feed is introduced; and “initial operations” are defined as the duration when operations accepts the system/facility and takes over."

Jan 1, 2000

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

By T. G. Phillips

"This paper gives an inside look at a bulk terminal and describes the preparations that must be made by a company in developing such a terminal and its position in today's traffic pattern. The following headings cover the subject material: (a) Traffic pressures, their detection and measurement, (b) position in the traffic flow -selection of site, (c) transportation connections -present and possible future routes, (d) engineering studies and costs, (e) contracts, the basic material for insured traffic, (f) financing, (g) budgetary control, (h) development of new techniques, (i) growth into new cargoes or cargo-handling methods and (j) consolidation."

Jan 1, 1968

By S. W. Marcuson, P. J. Mackey

The Canadian non-ferrous mining and metallurgical industry has made great strides in environmental protection during the past half century. The path taken by the copper-nickel smelting industry in reaching today’s level is traced in this paper. Following the practice at early copper smelters in Wales and in the US, Canadian smelters originally used tall stacks to disperse furnace of-gases. This was the normal mode of operation and was accepted by society and by Government. Gradually, Government regulations required fixation of sulphur dioxide emissions and Canadian companies responded with significant technical developments to achieve this result. The initial development in Canada of the first new technologies such as the Cominco Flash Suspension Roaster and the Freeman Flash Smelting Process - both representing early versions of the modern established flash smelting technologies - and then later technologies such as the Inco Flash Smelting Process and the Noranda Process, both of which continue to this day, are discussed in this paper in terms of their contributions to the development of environmentally friendly plants. The evolution of these and other technologies is also discussed. Some comments regarding how the industry will face the future are also included.

Jan 1, 2015

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By D. W. Tully

Sedimentary and volcanic rocks of the Timiskaming series trend west-ward across the property of the Upper Canada mine, forming part of the north limb of a regional syncline which is truncated on the south by the Larder Lake fault zone. A wide zone of schistosity strikes east-west through the sediments and volcanics. The central portion of this zone is occupied by a system of narrow gouge-filled fractures in highly altered rocks, mainly tuff, trachyte, trachyte porphyry and syenite porphyry. The alteration zones have developed through repeated stages of deformation and accompanying metamorphism. The initial stages were marked by carbonatization and sericitization, followed by silicification and the introduction of minor amounts of sulphide minerals. Gold was finally de-posited in relatively late fractures within silicified zones and pyrite. Repeated movements along the Up-per Canada break have offset post-ore dykes of minette and diabase, and have resulted in minor displacements within the orebodies.

Jan 1, 1963

By Andrew Abraham

Continual improvement is the key to success in today?s competitive global arena. You require tools that promote dynamic quality management, deliver cost savings to your bottom line and provide the foundation for process improvement. ISO 9000 and ISO 14001 management systems and OHSAS 18001 are those tools. Since their inception, the benefits of ISO management systems and registration have been touted as the way to achieve better bottom line results. This spurred many companies to embark upon the road to registration with high expectations. The potential benefits of ISO management system implementation and third party registration that are commonly provided by Registrars and consultants are compelling adverts for success. ISO 9001:2000 is promoted as an essential tool for systematic efficient and affective management controls that provide a framework for analyzing errors and improving a company?s internal operational processes. It also allows companies to comply with internal and external customer and regulatory requirements thus continually improving the quality of their products and services and thus enhancing customer satisfaction. This, in turn, leads to greater customer recognition and increased market share. ISO 14001 implementation and registration may assist your company in reducing its litigation risk, raw material and energy consumption, waste disposal costs and possibly non tariff trade barriers. It should also provide continuity of operations, enhanced operational efficiency and consequently a competitive advantage in the market place. Registration of your ISO 14001 management system should also improve your company?s profile and credibility leading to regulatory flexibility and improved community goodwill. All of this will be a catalyst for improved morale and pride by employees and management alike. Likewise, OHSAS 18001, the latest certification specification for Occupational Health and Safety Management Systems supports Occupational Health and Safety legal and regulatory obligations and compliance, manages & controls Occupational Health and Safety risks and improves performance, safety culture and efficiency. OHSAS 18001 is an audit certification, and not a legislative requirement. Suggested benefits of implementation include reduction in accidents, lost time and associated liability and insurance costs and improving reputation and credibility through demonstrated commitment to health and safety. The foregoing increases access to new customers, joint venture partners and financing The skeptics say these are motherhood statements and lack corroborative evidence, i.e., ?Show me the money!?

May 1, 2003

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974