Search Documents

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By Peter Dunn

London Mining Plc. is developing an iron ore project in Sierra Leone. The Marampa mine is a brownfield development effort, having been operated by others since the 1930?s until low iron ore prices forced closure. Peak production of the prior operations was approximately 2.5 Mt/a in the 1960?s. Following civil war In Sierra Leone, London Mining obtained the mining license in 2006 and commenced activity to redevelop the Marampa mining and processing operations. There are two ore deposits of interest for development as well as a resource comprised of tailings from previous operations. Phase 1 will be the mining of the tailings resource with a 1.8 Mt/a plant producing 66 per cent Fe sinter feed, expandable to 3.6 Mtpa. The first phase is currently under construction with start-up expected in the third quarter of 2011. Phase 2 will include development of the two ore deposits. These deposits are weathered secondary ore and the main primary ore resource. Phase 2 is currently under prefeasibility study and targets a final 16 Mt/a concentrate production in 2016. Outotec partnered with London Mining on testing efforts to develop the magnetic separation flowsheet using SLon VPHGMS machines to process the Marampa material. This paper explains the flowsheet development process for the weathered and primary ores commencing with sample characterization and detailed parametric investigations to evaluate SLon performance. The final flowsheet configuration is explained, including expected circuit recoveries and concentrate quality, clearly demonstrating the performance of the SLon VPHGMS circuit in iron ore tailings treatment applications.

May 1, 2011

By Ken Norris

"Campbell Mine which has been in continuous operation since 1949 has undergone numerous operational changes in the past 3 years. This paper describes the process changes which have occurred at the Campbell Mill since 1991. The paper discusses the engineering, construction and startup of the effluent treatment circuit, the new oxide filtering and merrill-crowe precipitation circuit, and the changes to the pressure oxidation circuit. Particular attention is paid to startup problems and solutions to these problems. A review of the benefits and results of these process changes is also discussed. Future changes are also briefly reviewed with anticipated goals and expectations.IntroductionCampbell Mine is a gold mine 100% owned and operated by Placer Dome Canada. It is located in Balmertown, Ontario which is located 300 kilometres northeast of Winnipeg, Manitoba. The Campbell Mine has been in continuous operation since 1949, producing nearly 8,000,000 ounces. In 1993 Campbell Mine is budgeted to produce 289, 750 ounces of gold at a cash cost of $157 US/ounce. Daily mill tonnage is budgeted for 1,430 tons/day but has milled as high as 1,600 tons/day on a consistent basis. Recovery in 1993 is 93.4% and is budgeted to average 94.5% in 1994.In the 1992 edition of the proceedings of the Canadian Mineral Processors conference I described the changes that were made at Campbell starting in 1989. This paper continues where the 1992 paper ended and discusses the changes to the Campbell mill since that lime. The changes to Campbell since January 1992 have been numerous with capital expenditure in the mill exceeding $14.1 million. This paper describes three primary projects since that lime: the effluent treatment project ($5.5 million), the oxide leach/filtering and merrill-crowe project ($4.6 million) and the pretreatment project ($2.81 million). The focus of this paper is to highlight the justification of each project, the design and engineering, and some of the initial operational problems and solutions applied to those problems."

Jan 1, 1994

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By P. West-Sells, B. Wassink, N. Fisher

Gold leaching from a commercial cyanide-amenable gold ore was studied at 25°C using sodium bisulfide-hydrogen sulfide solutions containing elemental sulfur. Gold extraction from the ore using 0.55 M NaSH, 4.1 atm (60 PSI) H2S, 1 g/L S8 and 26% solids by weight was about as good as the best extraction obtained by cyanidation. Maximum extraction was achieved in roughly 48 hours. Sulfur dissolves in the bisulfide solutions to form a mixture of polysulfides. Simple speciation calculations indicate that gold solubility as bisulfide complexes should be roughly ten times higher than in the absence of added zerovalent sulfur. The principal bisulfide complex is believed to be [Au(HS)2]-. Gold dissolution is favoured by increasing HS- concentration and by increasing H25 pressure. Polysulfide complexes of gold are also likely to be formed, and may contribute substantially to gold leaching. Two experiments using pure gold were also performed. Up to 100 mg/L gold was dissolved in 140 hours using 0.55 M NaSH, 1 g/L added elemental sulfur and 6.2 atm H2S.

Jan 1, 2005

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2010