Search Documents

By Clappison D. J

Since its formation in Papua New Guinea and raising of A$2 million in 1980, Niugini Mining Limited (NML) has grown to a company capitalised on the Australian Stock Exchange at about A$350 million. In 1995 the company produced some 237 000 ounces of gold, 700 000 ounces of silver and nearly 5000 tonnes of copper from its operations at Red Dome, in North Queensland and San Cristobal in The Atacama Desert of Northern Chile. This production contrasts with Niugini Mining's first mining venture at Mt Victor in the Eastern Highlands of PNG which yielded 20 000 ounces of gold and 11 600 of silver between 1987 and 1989. Following the formation of an exploration joint venture in 1982 with Kennecott Explorations (Australia) Ltd, now a subsidiary of RTZ, Niugini Mining's early recognition of the gold potential of volcanic rocks at plate margins led to discovery of the Lihir deposit in July 1982. This deposit containing about 42 million ounces of gold in resources, is one of the largest undeveloped gold deposits in the world. Following raising of equity funds through the float of Lihir Gold Ltd and debt finance in 1995, construction of the mine at a cost of US$673 million is now underway with first full-scale production at approximately 600 000 ounces of gold per year expected in early- 1998.

Jan 1, 1996

By Northcote GG

There are many underground mines with shaft or decline access with limited production capacity or where the mine may become uneconomical as trucking costs escalate with increasing depth of the decline. In such cases a need may exist for a shaft hoisting system which can be constructed more quickly and more economically than a shaft sunk by conventional methods. Relatively cheap small diameter shafts can be constructed by raise boring. This paper describes a simple hoisting system which has been designed to take advantage of the benefits of raise boring. The system uses twin bored raises with a double drum winder hoisting a skip in each hole. The design concept is based on 1. accepting that the raises cannot be truly straight or vertical, 2. using the raise to guide the conveyance, and 3. minimising operating, maintenance, and capital costs. The hoisting system requires a certain degree of accuracy in the alignment of the twin raises. A survey of raise boring practice showed that the required accuracy could probably be achieved with conventional techniques. However it was thought it would be necessary to survey the pilot hole during drilling and to be able to correct the hole if deviation became

Jan 1, 1978

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

Rock formation at shallow depths is generally associated with complex geology consisting of many joints, fractures, bedding planes, etc. Fragmentation results from primary blasts in such strata are therefore significantly influenced by structural discontinuities. To evaluate the role of discontinuities, which is of great use in the design of blasts in such conditions, a two-stage investigation program was taken up. In the first stage, model scale tests were conducted with single and double holes with the strike of discontinuities parallel and perpendicular to the face. Later, field studies were conducted in a limestone mine and a coal mine. Blast patterns were modified based on the results obtained from model scale blasts. Secondary blasting was taken as a measure to assess blast performance in the field, whereas mean fragment size, fine and coarse fragmentation indices were considered as fragmentation measures in model scale tests. Model tests indicated confinement of explosive energy by the discontinuities surrounding blasthole. Crater shape and size were significantly influenced by the orientation of joints with respect to the face. Modified blast designs with decreased burden x spacing patterns resulted in improved fragmentation in the field. A reduction of about 12 per cent in explosive consumption was recorded with modified blast designs. Boulder formation was observed to decrease by about 79 per cent as well.

Jan 1, 1995

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

By Daziel M, Corke P

Unit cycles in mining have not changed for many years. Productivity increases over the past three decades have mainly been achieved by using larger and heavier machines. This investment in size has probably reached the point of diminishing returns and increased productivity in the future will have to be generated by other means. One way of achieving this is through automation of selected unit operations, eg dragline overburden removal, truck haulage, ground support installation and secondary breakage. Although, in the past few years, there has been significant progress in this direction, we are still a long way away from even partial automation - especially in hard rock mines. This paper addresses the technical obstacles facing mining automation; suggests ways by which these obstacles may be overcome and identifies the role of industry groups and research providers in this process.

Jan 1, 1997

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

Kidston Gold Mines Limited (70 per cent Placer Pacific and 30 per cent Public Shareholders) has been mining the Wises Hill Pit since late-1984. The Wises Hill Deposit is a large low grade gold deposit and as such is highly sensitive to economic parameters. The uniformity of the orebody has allowed a bulk mining method to be used, with minimal dilution. Total reserves defined to-date are 64 160 OOOT at a grade of 1.60 g/t gold. Mineable reserves remaining as of January 1992 are 36 357 OOOT at a grade of 1.28 g/t gold.Mining investigations to reduce the impact of lower gold prices, the effect of decreasing headgrade and increasing mining costs have focused on wall steepening.

Jan 1, 1992

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

DR. WARK, said: I have not come to Broken Hill to tell you how to conduct flotation operations; indeed, during my short stay here I have already learned much concerning the process, of the many difficulties which have been overcome, and of those still awaiting solution. My purpose to-night is rather different. All who have been concerned with the operation...

Jan 1, 1933

By M D. Raine, J K. Bartlett, S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of fields that make up the Central Victorian Goldfield. Since 1993, Bendigo Mining NL has been carrying out an extensive re-evaluation of the goldfield and is currently well advanced in developing an underground mine. The sediment-hosted auriferous quartz reefs are structurally complex and closely associated with anticlinal axes and reverse faulting. The gold within the quartz reefs is characterised by both its coarse nature (100 up to >5000 ¦m) and its erratic distribution; as a result, the Bendigo Goldfield is classed as an extreme nugget effect system. This characteristic ensures that the Bendigo mineralisation is very challenging to sample and evaluate. In this case, diamond drilling is a good measure of structure and geological continuity, but a poor measure of grade and grade distribution. Drilling, combined with on-reef development, bulk sampling and detailed geological studies are required for resource evaluation. For grade control a balance has to be sought between sample representativness, cost, turn around time and practicality. Extreme nugget effect deposits like Bendigo, require the use of bulk samples in order to be representative. However, the cost and turn around time is significant. As a result, a micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can define ore from waste. Bulk sampling and on-vein development are still necessary for resource and reserve estimation.

Jan 1, 2003

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

By Grinenko VA

Mineralogical, chemical, and isotopic data have been obtained for samples from 11 volcanoes and 4 kortlandite intrusives on Kamchatka.Similarities and differences in ore-bearing and barren intrusives are discussed. Differences in sulphide mineralization and sulphur isotope compositions of intrusives are explained in terms of the "auto-sulphurization" hypothesis which involves the redox conditions of the host rocks. possible role for carbon in nickle sulphide ore formation is also considered.

Jan 1, 1990

In line with the recommendations of The AusIMM/AMIC Joint Committee Report in 1981 Isa Mine ore reserves are quoted in proven and probable categories (recoverable ore reserves). Internal reporting considers geological mining and extraction reserves in terms of proven and probable categories. Proven reserves are subdivided into detailed and confirmed ore. External reporting includes a possible ore category (not a reserve). The basis for these divisions is the spatial distribution of sampling data. Proven ore is defined by data 80m apart or less and probable ore by data 80m to 150m apart. Within the proven ore category detailed ore is defined by data 40m apart or less and confirmed ore by data 40m to 80m apart. Kriging is used to provide tonnage and grade information for the currently producing 1100 and 1900 orebodies. Kriged cross sections are initially produced to coincide with existing geological sections and are used for stope design. Stope ore reserves calculations are ideally performed at three discrete design stages, which in order of increasing accuracy are: preliminary design (PD), final design (FD) and ring design (RD). At each of these stages Kriged meshes incorporating the most recent sampling information are produced for reserve calculations. Historically derived mining and extraction factors are applied both to global reserves and individual stope reserves to reflect changes in geological and mining conditions as well as the sequencing of extraction. These factorised reserves are then inserted into the computerised reserves inventory system (RIN). Monitoring of individual stope performance continues into the production stage with input from planning, research, survey and production personnel. This allows actual extraction factors to be derived for comparison with predicted factors, providing some measure of stope performance.

Jan 1, 1987