Search Documents

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S D. Dessureault

In one of North AmericaÆs largest mines, which contains more than six active coal-producing faces, mine controllers must meet the complex challenge of adhering to the mine plan while also ensuring customer quality. Fleet management systems (FMS) provide many different avenues to control production flows, from the faces to the various pit crushers. Nonetheless, mine controllers must balance a variety of factors such as unplanned downs, differing customer demands, their own daily key performance indicators (KPIs) related to equipment utilisation, among others. Deviating from the short-term mine plan is the most common means of balancing the other factors, since adherence to the plan is traditionally only measured during the weekly variance meeting with engineering staff. However, such deviation may be one of the most costly responses, as long-term scheduling issues may arise such as multi-face dead-heading or insufficient stripping. This paper focuses on the development of a system for real-time adherence to mine plan within a control room environment. This system is part of a larger blending-focused, multi-million dollar project with elements of a centralised remote control room, developed at the University of ArizonaÆs Mining Information Systems and Operations Management (MISOM) Mine Control Center (MC2). The mine plan (MPL) component of the overall blending system integrates both historical and real-time FMS data with mine plan requirements directly sourced from original systems (no additional input required). The measures, displayed largely as graphs, have tools to help controllers manage the production to facilitate adherence to the plan. Some measures are designed to motivate crews to perform by inciting competition between crews, softened through a study of the controller culture. The MPL component was deployed at the mine, and the before and after deployment adherence was measured. This paper discusses the technical development of the new tool, its deployment, and an ethnography (study of culture) to understand controller motivation.

Sep 26, 2011

By J Wood

Steady depletion of the world’s primary copper reserves coupled with a meteoric rise in electronic waste (e-waste) generation has led to secondary copper processing assuming an ever-increasing importance within the global copper industry. Treatment of secondary copper feeds at existing smelting operations has traditionally been performed in the Blast furnace, Peirce-Smith converter and/or anode furnace. In the past decade or more, bath smelting technologies have been preferred for the processing of these materials due to their superior environmental performance and flexibility to operate under a wide range of conditions. This paper focuses on the pyrometallurgical processing of copper secondaries in the Outotec Ausmelt TSL Furnace and some of the unique issues facing secondary copper smelters and downstream gas handling/cleaning equipment.

Aug 8, 2011

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

By testing rotary-drag bits in granodiorite it was found that an increase in bit clearance angle from 241 0 to 33° decreased insert wear. Severe wear has precluded economic application of rotary-drag drilling in abrasive rock even though fast penetration rates have been achieved.From a limited number of tests and from theoretical considerations, the insert wear was inversely proportional to the thrust on the bit This effect follows the marked reduction in the linear distance traversed by the inserts, for a given depth of penetration, as thrust increases...

Jan 1, 1969

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

Construction of Western Mining Corporation's nickel refinery at Kwinana, Western Australia, commenced in July, 1968. Production of 15,000 tons per annum of refined nickel metal will commence early in 1970, The plant will also produce approx- imately 150,000 tons of ammonium sulphate0 The ammonia leach process which was developed by Sherritt Gordon Mines Ltd., and has been in operation at their plant at Fort Saskatchewan, Alberta, Canada, for the past 15 years, will be used at Kwinana. The refinery will cost approximately 435 million, and will employ upwards of 250 people.

Jan 1, 1969

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By M Ziemski

The provision and management of energy in both fuel and electricity forms is an increasingly important consideration for mines. Pressures from communities, governments and markets are increasing towards more transparent and improved energy management. Combined with the energy-water nexus, where water and energy are closely related in the operation of a mine, this emerging business climate means a more thorough and responsible approach is required for the acquisition and use of energy, as well as the release of emissions. Many of the complexities in potential new ore bodies are borne in remote locations, high altitudes, low grades, arid climates and deep deposits. Each of these challenges affects the successful provision of energy. In combination, such challenges can leave an operation seemingly unviable from an energy perspective, especially when approached from a traditional mining energy feasibility lens. This paper discusses some of the energy alternatives currently available and emerging in the mining industry. Both energy supply and demand options are considered, which can provide a very different energy footprint with the flexibility to address, and potentially overcome, major energy challenges for a mine. CITATION: Ziemski, M, 2018. Energy complexities in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 106–111 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Raczej I, Defant M

Pre-Miocene igneous rocks from the Phili pine island arc are characterised by 87Sr/86Sr and 143Nd/144Nd ratios typical for intra-oceanic island arcs where sediment involvement in the magma genesis was minor. Lead isotopic ratios are similar to Indian Ocean MORB (Mukasa et al., 1986a,b). Pliocene to recent volcanics, however, have more radiogenic Sr and Pb and less radiogenic Nd, except for the volcanics of the Bicol Arc, which have similar isotopic signatures as the Pre-Miocene rocks. We suggest that Pre-Miocene magmas and Bicol-Arc magmas have been generated in response to the subduction of the Philippine Sea Plate, their isotopic characteristics reflecting the composition of Philippine Sea crust. The Bataan arc magmas may reflect the larger amounts of sediments available for subduction in the South China Sea, while magmas of the Mindoro Arc, which are characterised by the most radiogenic Sr and least radiogenic Nd, may have been contaminated by slivers of the Mindoro-North Palawan terrane, which have been carried down to mantle depths after the collision of this terrane and the Philippine arc in Miocene (McCabe et al., 1982). This interpretation implies that Nd (and by inference other REE) can migrate from the subducted slab to the mantle wedge. Thus, variable Nd-isotopic ratios in island arc magmas (e.g. Sunda, Lesser Antillas) may not he a primary feature of the mantle wedge but a consequence of the release of Nd from the subducted slab.

Jan 1, 1987

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

By M Creech

During the 1990s, wider and more productive longwall panels were being introduced into the Newcastle Coalfield. The strata of the Newcastle Coalfield incorporate numerous massive sandstones and conglomerates, some of which formed the immediate roof of the coal seams being mined. The unexpected implications of introducing wider panels into this geological environment included more variable and increased subsidence, severe periodic weighting (with associated mid-face falls) as well as windblast.Subsidence prediction at the time was based on empirically derived data essentially relating subsidence to the width/depth ratio of the panel without accounting for actual widths, nor the impacts of variable geology. This approach required modification as locally derived data was gathered and reinterpreted.The interaction of massive strata located close to the roof of the mined seam resulted in dramatic implications for some of the operations. When associated with longwall goaf geomechanics severe periodic weighting events and crippling mid-face roof falls were the consequence. When associated with narrower panels and shortwall goaf geomechanics, mines in the region experienced aggressive windblast events. The relationships between the overlying massive strata, longwall panel geometry and the various risks encountered during this period is in the author’s opinion, the most concise still documented.As the extensive coalfields of Queensland turn to underground mining operations the relevance of these experiences cannot be underestimated. This paper will discuss recent developments as well as incorporating diverse subjects such as microseismic monitoring, low frequency radio emissions and ‘electrophonics’ as they relate also to the topic.Like Moriarty, massive strata can be disguised and can offend when you least expect. This paper documents a trail of crimes committed by conglomerate in the Newcastle Coalfield that were inflicted on the general public, miners and mining equipment. Although this paper concentrates on the criminal behaviour of conglomerate, this story is also relevant to other massive units such as coarse sandstones that may be more difficult to identify and apprehend. Currently Moriarty remains at large and able to reoffend at any time, once again taking advantage of the unwary.CITATION:Creech, M, 2014. Moriarty was a conglomerate – experiences and implications of coal mining under massive strata in the Newcastle Coalfield, in Proceedings Ninth International Mining Geology Conference 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By K M. Cook, D Clark

Fatality prevention and zero harm are key focus areas for resource companies. However, they remain an ongoing challenge for high hazard industries, including the mining sector. As one example the latest International Council on Mining and Metals (ICMM) Safety Performance Report shows that, while there is generally a declining fatality trend since the organisation commenced publishing data in 2012, there were still 33 fatalities across member companies in 2022 (ICMM, 2023b). Every fatal incident brings significant pain and suffering to the colleagues, friends and family of those involved, however the failures and causal factors leading to each incident are frequently very familiar to people working in the industry, particularly those tasked with managing risk and safety. In the words of Dame Judith Hackitt, Grenfell Tower Fire Investigator, ‘there are no new accidents – just different people making the same mistakes because they haven’t learned’ (Hackitt, 2022). The recurring themes in terms of the nature of fatal hazards and their associated causes across the mining sector show that, despite improvements evidenced by the favourable declining fatality trends over the long-term (in general and outside of catastrophic multiple fatality events), changes are required to achieve fatality elimination and the aspiration of zero harm. This extended abstract and the accompanying presentation apply a mining frame of reference to the idea that there are no new accidents, examining how this applies within the industry and why the lessons from past failures are not always well understood or applied to prevent the reoccurrence of material unwanted events. Many contemporary mining and resources organisations have extensive internal incident history data and a wide variety of information on fatality incidents is publicly available, including the annual ICMM Safety Performance Report. This extended abstract and the accompanying presentation explore how this existing data can be used effectively to learn from the past and proposes practical ideas regarding strategies for successful knowledge transfer to the workforce as a key component of preventing history repeating and improving safety performance across the industry. As noted by ICMM, ‘sharing lessons from failure is vital to improving health and safety, but it’s not enough’ (ICMM, 2023a).

Apr 16, 2024

By P J. Bangerter, G D. Corder

With the societal desire and drive towards low carbon energy sources, there is a growing awareness of the important role that minerals and metals will play with renewable energy technologies. Copper is an essential metal for technologies that generate energy from renewable sources, in particular for wind and solar photovoltaic energy systems. A recent report (Arrobas et al., 2017) estimated that the median increase in copper demand through to 2050 for wind technologies and for solar photovoltaics would need to be 250% and 300% respectively to meet the goal of a 2°C global temperature increase scenario compared with a 6°C global increase, which is largely an extension of current trends (IEA, 2018). The aim of this extended abstract is to demonstrate with the necessary increase in copper production for renewable energy technologies that sound sustainability performance across the global copper value chain is to the benefit of government, society and industry.CITATION:Corder, G D and Bangerter, P J, 2018. Balancing the benefits and impacts of future copper demand – climate change and arsenic, in Proceedings Life-of-Mine 2018, pp 17–19 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0·01 per cent) and cobalt (less than 0·002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

Models of the genesis of existing ore oodles and targetting of exploration for new mines are greatly enhanced by an-understanding of the plate tectonic environment existing at the time of mineral emplacement. In areas of recent or active tectonism, a study of the present-day crustal and upper mantle structure is an obvious starting point in unravelling the evolution of the accessible upper crust. Bougainville is the northern-most island in the Solomon Islands arc. A 7km deep trench almost 100km off its western coast marks the commencement of subduction of the Solomon Sea plate beneath the Pacific plate. As outlined by the seismicity, the subducted crustal slab under the southern half of Bougainville reaches the axis of the island at about 100km depth, from which point it dips near vertically another 300km into the upper mantle. Large surface blasts at the Bougainville Copper Mine at Panguna, Bougainville, Papua New Guinea were used to derive an unreversed upper crustal profile of the island. The crust appears to be relatively simple, being comprised of a 5km deep layer with a P-wave velocity of 4.5km/sec, overlying a l0km thick layer with a P-wave velocity of 7.2km/sec. Constraints on the 15km mantle depth were provided by the identification of both P to and S to P phase conversions of seismic waves from local shallow earthquakes at the Moho boundary. An upper mantle velocity of 7.95(¦ 0.15) km/sec was measured from travel times of selected shallow earthquakes along the strike of the island arc.

Jan 1, 1987

By V Lickfold, A J. Crawford, A J. Wilson

A total of 12 alkalic porphyry centres of Late Ordovician age have been discovered in two mineral districts within NSW. The alkalic porphyry deposits are hosted within shoshonitic volcanic centres that formed where a major cross-arc basement structure (the Lachlan Transverse Zone) cut the Ordovician Macquarie Arc. The Macquarie Arc was amalgamated with the back-arc basin sediments of the Wagga Marginal Basin and with the proto-Pacific margin of Gondwanaland to form the Lachlan Fold Belt after the cessation of arc magmatism in the Late Ordovician. Within the Ordovician volcanic belts of NSW, the alkalic porphyries are the most significant mineral deposits economically. The combined resource of the Cadia district porphyries (729 Mt @ 0.79 g/t Au and 0.30 per cent Cu) makes Cadia the worldÆs seventh largest known porphyry gold system and the largest known gold resource in an alkalic porphyry system (574 t Au). Hydrothermal alteration in the alkalic porphyries comprises a complex sequence of potassic, calc-potassic, sodic, calc-sodic, propylitic and late-stage, typically fault-controlled phyllic assemblages. Hematite dusting is common in many of these alteration assemblages, giving the intrusions and the altered volcano-sedimentary host sequences a distinctive pink-orange colouration. Intensely developed hydrothermal alteration assemblages are localised to within a few hundred metres of the composite intrusions that sourced the mineralising fluids, making these deposits difficult exploration targets. Sulfides are typically zoned, with several of the deposits having bornite-rich cores, chalcopyrite-dominant annuluses and pyritic outer haloes. Gold is well correlated with bornite in most of the deposits, and with chalcopyrite at Cadia Hill.

Jan 1, 2002

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

By B P. Voutharoj, R A. Dutch, M Paknezhad, T Ostersen

With the proliferation of new sensor technologies, acquiring multiple data sets over the same ground is becoming cheaper and easier than ever. This new, higher resolution multivariate data provides a significant resource for exploration and resource geologists but comes with the added complexity of effectively integrating the various data sets in useful and meaningful ways to elucidate new geological understanding. Both geophysical data sets and hyperspectral data are extensively used for exploration targeting, providing different information at different resolutions and crustal scales. One of the biggest challenges comes from trying to effectively integrate data sets that record very different physical properties, across the different scales these data are captured at, in a way which can allow for a data-driven analysis of these combined data sets.

Sep 1, 2024