Search Documents

By AUIMM AUIMM

Continuous Improvement The Council of the AusIMM should expedite the introduction of a continuous professional education policy along the lines of that to be proposed to you by David Pollard today. The Education and Accreditation Committee must continually review the training needs of the next generations of mining industry professionals. It should continue to demand and encourage the creation of the schools for the training of such people. The AusIMM could even put greater onus upon university researchers to accredit university post graduate degrees.

Jan 1, 1994

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By R Burgess-Limerick, J Haight

A review of mining automation experiences was undertaken on behalf of the National Institute for Occupational Safety and Health (NIOSH). The research included a review of literature and guidance materials; analysis of automation related incidents and visits to surface and underground mines in Australia, Brazil, Chile, South Africa, Sweden and the USA.

Apr 16, 2024

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By M Alston

Many organisations struggle to yield meaningful outcomes from incident investigations. This paper will demonstrate that we can discover systemic issues by rethinking the ‘Why’ and ‘How’ of investigations, fostering genuine risk reduction. Key points: 1. Shift from ‘prevent recurrence’ to ‘learn and reduce risk’: conventional investigations focus narrowly on recurrence prevention, resulting in narrowly focused investigations with limited ability to identify and reduce organisational risk. Redirecting our objective to learning and improvement opens avenues for broader risk mitigation. 2. Understanding daily work for risk insights: recognise that work is not always completed in full compliance with procedures. Workers will adapt how they complete tasks influenced by the conditions and management systems that exist every day. Understanding the conditions and systems affecting everyday work is vital for uncovering systemic risks. 3. Unearth systemic issues through in-depth exploration: many investigations address surface concerns such as lack of training, incorrect procedures, equipment not being maintained, and missing overarching organisational risks. Systemic, organisation-wide risks are not identified. To discover these systemic issues and create shared learnings, investigators must question management systems, including resourcing, planning and risk management. 4. Design actions for safe failure: common actions like discipline and training fall short and do not reduce risk. Resilience emerges from well-designed controls. Incorporate planning, better resources, interlocks, and guarding to bridge the gap between task execution and risk. 5. Investigation Reports as a Business Case: Investigation reports should not simply state historical information regarding an incident. They are to facilitate decision-making and be presented as a business case to drive change. Organisations can move beyond localised risk and ineffective administrative actions by changing investigation objectives and methods. They can facilitate learning, understand daily work intricacies, identify systemic issues, and enhance the capacity for safety, driving lasting risk reduction.

Apr 16, 2024

By Jin C, Shi X

The electrochemistry of leaching gold with thiosulphate has been studied systematically by using electrochemical techniques. Results show that the current peak of anodic dissolution of gold occurs at about 50 mV(SCE) and there is passivation in the polarisation curve in the thiosulphate solution in the absence of ammonia. Ammonia markedly improves the anodic dissolution rate of gold and reduces the passivation as well as making the current peak shift negatively. Results also show that there is no current peak for a cathodic process in the range of 0 -900 mV(SCE) in the thiosulphate solution in the presence of oxygen but absence of cupric ions and ammonia. In the solution containing 0. 1 mol/L cupric-ammonia ions, the peak occurs at about -400 mV (SCE) and the cathodic process is characteristic of a catalytic reaction. Oxygen presents a predominate effect on the cathodic process. Based on the electrochemical investigation, the following mechanism of leaching gold with ammoniacal thiosulphate has been proposed. Ammonia reacts primarily with gold ions on th anodic surface of gold and the formed A (NH3)2+ rea~s then with S2O 3 in solution to form the stabler Au(S203) 2 . Cu (NHS) 4 gains electrons on the cathodic surface and is reduced to CU(N) ? which is then oxidised by oxygen and regenerated into Cu(NH3) 4 after entering the solution.

Jan 1, 1993

Fluid inclusions and sulfur isotopic compositions were studied in a possible extension of the Toyoha polymetallic vein deposit. The objective of this work was to gain a better understanding of the ore depositional conditions, sources of ore constituents, and distribution of mineralizing fluid in the region. Fluid inclusions in sphalerite and quartz show that most homogenization temperatures range between 190¦ and 290¦C. Most salinities range from 0.0 to 3.4 wt per cent NaCl equiv. Sulfur isotopic compositions of ore minerals (pyrite, sphalerite and galena), determined by a conventional technique, range between 1.3 and 7.7 per mil. The mineralizing fluids were characterized by relatively low and various temperatures and low to moderate salinities compared to those at the southeast region of the main ore bodies (Izumo and Shinano veins) where rare elements such as tin, tungsten and indium occurred. Obtained temperatures and salinities were attributed to the mixing of hydrothermal fluids with groundwater. Sulfur isotopic data suggest sulfide sulfur was of magmatic origin. Isotopic temperatures, estimated from the isotopic fractionation factor between sphalerite and coexisting galena, are between 195¦ and 322¦C. The temperatures are only consistent with fluid inclusion homogenization temperatures in sphalerite or coexisting quartz when sphalerite was a honey-yellow coarse crystal lacking conspicuous colored growth bands. This suggests the detailed classification of mineral pairs growth textures will be necessary for precise in situ measurements to obtain reasonable eothermometric results.

Jan 1, 2002

By Bulters J, Sheppard I

Two blasthole density logging programmes have been conducted on the Mt Whaleback iron ore mine to evaluate the use of this type of logging as an aid to blast pattern design. The first programme also involved the setting up of a Density Test facility with which to calibrate the density probe. The programmes indicated that about 22-23 blastholes can be consistently logged per day at a cost of $1.30 per metre. Even though this is only half the rate required to log the average number of blastholes drilled daily on Mt Whaleback, testwork indicated that no significant loss of accuracy results if only half the holes in a pattern are logged. The major results of the programmes were: 1. The density range for black pyritic Shale is 2.2-2,9 g/cc. 2. The density range for soft to medium hard BIF is 2.1-3.0 g/cc. 3. The density range for hard BIF is 3.0-3.6 g/cc. 4. The front row blastholes show consistently lower densities than the main body holes due to blast damage. 5. A low density zone extending to a maximum depth of 6 m occurs at the top of most blastholes and results from blast damage from the bench above. These density results have been used to implement savings in drilling and blasting via pattern expansion and charge optimisation of blastholes. Eight ore

Jan 1, 1986

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C Hall, P Hazell, C Wilson

Every mine is situated within a water catchment – a catchment with potentially many other land uses. A mine may take up a relatively small area in that catchment, but its operations have the potential to affect the whole catchment and long after that mine has ceased to operate. Therefore, the residents of any given catchment have the right to feel secure in the knowledge that their catchment, and indeed the wider environment, will not be degraded by mining activities. Much conflict can arise when this confidence does not exist.But, imagine if a community not only felt confident that their catchment would not be degraded by mining activities, but was also confident that their catchment would be left in a better and continuously improving condition – with improving water quality, biodiversity and soil - and a strengthening, more resilient economy. CITATION:Hazell, P, Wilson, C and Hall, C, 2018. Landscape regeneration lessons learned from Mulloon Creek, in Proceedings Life-of-Mine 2018, pp 125–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

Detailed underground mine design and optimisation studies undertaken by the author over the past few years have clearly demonstrated that additional value can be created by varying the cut-off grade (COG) spatially throughout a deposit as well as over time. This additional value can be particularly significant for marginal operations. This paper, by way of worked examples, illustrates the conceptual and practical considerations of applying a differential cut-off policy for an underground mine to both maximise value and manage risks associated with production and metal price volatility. Consideration is given to both the design stage of a new mine and to the strategic and practical application of a differential cut-off policy in an operating mine.

Jan 1, 2005

By M Tayebi-Khorami

There is an increasing trend in the extraction and development of copper resources from complex deposits. The complex deposits pose mineral processing challenges, as they often contain low grade copper ore, relatively large quantity of clay minerals, complex texture, very fine disseminated ore, high amount of pyrite, and high level of impurity elements such as arsenic. With the amount of arsenic in concentrates increasing and with environment, occupational health and safety regulations becoming more restrict, there is a need for a processing method that results in no arsenic emissions and captures all arsenic while immobilizing it in a compound that is stable under a wide range of conditions, so it is suitable for long-term disposal. Some development work has been undertaken to examine the most effective arsenic treatment option for complex orebodies that contain arsenic, but a technically robust and economically viable option has not yet been developed. Previous research has demonstrated the possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp in the single mineral systems. The selective flotation of enargite from copper sulphides in a real complex ore system was studied by Tayebi-Khorami (2016), which is summarised in this paper. CITATION: Tayebi-Khorami, M, 2018. Arsenic in complex orebodies, in Proceedings Complex Orebodies Conference 2018, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Taylor L. M

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry. Some of the computer programs previously used to predict rock motion employed polygonal elements with comers and sides to model the rock (Cundall, 1971; Walton, 1982; Taylor, 1983). This approach allows the elements to bulk because of the corners and the aspect ratio. However, tracking the many interactions of the comers and sides of the elements is a computationally intensive process. Several other rock motion computer programs were developed that employed spherical elements, (Schamaun, 1984; Gorham-Bergeron et al, 1987) but they lacked correct bulking mechanisms or could not be vectorized for efficient execution on vector processing machines. A new spherical element code called DMC (Distinct Motion Code) (Taylor and Preece, 1989a, 1989b) has been developed this past year. DMC was designed and written to take advantage of super-computer vector processing capabilities. The efficiency has also been increased through the use of spherical elements, explicit time integration and a new contact search algorithm. When spherical elements were chosen for efficiency, some physically correct mechanisms for capturing the bulking behavior of the rock mass also had to he developed. This paper will treat several mechanisms that were developed to allow spherical elements to exhibit correct hulking behavior.

Jan 1, 1990

A review of publicly available coronial inquiries into fatalities that have occurred within the resources sector since the year 2000 reveals that a loss of corporate memory has been a contributing factor in 40 per cent of these accidents (National Coroners Information Service, 2010, Appendix B). With the highest levels of employee turnover within the Australian economy, increasingly complex operations and an ageing workforce, the management of corporate memory within the Australian resources industry poses a significant and often unrecognised safety risk.    The North Parks airblast of 1999 is used as a case study to highlight how corporate memory loss poses a significant hazard to resources projects and how such incidents will continue to occur if corporate memory is not effectively managed. Best practice from other industries is discussed to demonstrate how knowledge management systems can effectively work. This paper discusses how systems can be put in place within the geographically diverse resources sector, and how at the heart of any knowledge management system a culture of knowledge management needs to exist within an organisation.   The paper then discusses the importance of retaining key personnel and utilises findings from primary survey data collated in 2009 to show the size of the retention problem within the industry. From the data possible solutions to retaining key staff are proposed.   Finally the large and increasing role of contractors and consultants within the industry is discussed and methods of managing their knowledge are proposed.

Jun 1, 2010

By F Mwijage

"The benefits of measuring blast movement to reduce ore loss and dilution have been recognised by many people for many years and various methods have been used with limited success. Geita Gold Mine is running the pilot study on the blast movement monitoring (BMM) system which is a revolutionary method developed and patented by the University of Queensland and Blast Movement Technology (BMT). The system consists of directional transmitters placed within the shot prior to blasting, which are then located after the blast with a special detector and then the data is processed with purpose-designed software.As part of continuous improvement on grade control, Geita Gold Mine is running a research project in all operating pits with the objective of: quantifying the three-dimensional blast muck pile movement and finally utilise the movement data to define post-blast ore polygons and incorporate the movement dynamics during block modelling,quantify the potential savings for ore loss and dilution,improve mine geologists knowledge of blast dynamics, andstimulate greater co-operation between drill and blast engineers and geologists to achieve optimum blast designs.To any operation with selective mining, it is critical to the economics of an operation to control ore loss and dilution; getting it wrong will result in significant lost revenue. Implementation of ongoing pilot study on electronic balls as determinant on blast movement dynamics on ore would be of longer term solution and big investment pay back.CITATION:Mwijage, F, 2012. Pilot study on blast movement monitoring at Geita gold mine, in Proceedings Narrow Vein Mining 2012 , pp 49-58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By S Tierney, D Cumming-Potvin, I Thin, Y Potvin, D Grant

The preliminary modifying factors for future stope design in the Southern Mine Area of Olympic Dam consisted of only a single, arbitrary value of Equivalent Linear Overbreak/Sloughing (ELOS). In order to improve this, a study was conducted which developed a more comprehensive methodology for assigning ELOS, Equivalent Linear Lost Ore (ELLO) and Equivalent Linear Fill Overbreak (ELFO) to individual stope faces based on geotechnical and mining parameters. The approach used was to look at the simple cases, which were classed as vertical stope walls in good ground (RQD 80-100%), divided into wall orientations (North, South, East, West). The stope walls were also split based on the blasting practice used (toeing, parallel or a combination of the two). The expected ELOS and ELLO from these ‘base cases’ are then modified by parameters which have historically been found to affect stope performance (Hydraulic Radius and Q’). The size of the effect found in the historical data determines the ELOS / ELLO applied. The methodology was summarised in an easy to use flow chart and was applied to all of the proposed stope shapes for the Southern Mine Area and summarised per mining block. This allowed each iteration of the mine plan to be assessed in terms of overbreak (both rock and vertical fill exposures) and underbreak.

Mar 15, 2021

By G J. Zhang

The shape and particle size distribution of caved ore mass in sublevel caving were investigated in this study. The paper first reviews the main factors affecting the shape and characteristic of caved ore mass in sublevel caving and then through the experimental blast testing with cement-sand concrete models, the shape and particle size distribution of caved ore mass were found out. The experimental results indicated that the shape and particle size distribution of caved ore mass was similar to that of the drawn loose body. This finding presented a new perspective for the future study on the ore drawing theory and on the optimisation of structural parameters of sublevel caving. The structural parameters must meet the principle that the shape of the drawn body is in consistency to the shape of caved ore mass.

Jul 11, 2011