Search Documents

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By J L. Merritt

Contour banks and waterways are standard soil conservation measures to assist farmers reduce the impact of gully erosion on sloping cropping land by reducing the slope length to the interval between the banks. The Universal Soil Loss Equation (USLE) developed by the USA Department of Agriculture Soil Conservation Service in 1930s predicts the long-term average annual soil loss (A).The equation is the product of the rainfall erosivity factor (R), the soil erodibility factor (K), the topographic factors of slope length and angle (L and S) and the cropping management factors (C and P). Contour banks reduce the slope length (L) only.Contour banks are a constructed earth embankment, incorporating a channel on the upslope side, typically traversing a slope on or close to the contour to control and/or prevent the erosion of that slope. The banks are also referred to as graded banks, terraces, or bunds (DSITI 2015). Contour banks are either broad based or narrow based. Broad based banks allow the passage of the machinery over the banks whilst narrow based bank batters are too steep preventing the passage of machinery. Waterways are a stable, longitudinally sloping water disposal area of sufficient capacity used to discharge surplus runoff from the contour bank and to allow it to flow to a lower level without causing erosion (DSITI 2015).The mining industry must decide what the role for contour banks and waterways is in each operation’s rehabilitation and closure plan.CITATION:Merritt, J L, 2018. Contour banks in spoil rehabilitation – a matter of timing, in Proceedings Life-of-Mine 2018, pp 147–149 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By G McLeay, T Moran

Long Shaft has traditionally been seen as one of the most challenging mines in the Kambalda area with operations having been suspended by the previous owners in 1999. When mining recommenced in October 2002, the current owners (Lightning Nickel) decided that a different approach was required for mining operations in such an aggressive geotechnical environment. This paper describes how Lightning Nickel has successfully and safely operated the Long Shaft complex on a traditional mining approach, which encompasses the key learnings of the previous owners.

Jan 1, 2005

By A Tsoy

This abstract describes long-term mining schedule optimisation approach that may be suitable for complex marginal projects and is based on modern scheduling techniques. CITATION: Tsoy, A, 2018. Strategic mine schedule optimisation, in Proceedings Complex Orebodies Conference 2018, pp 91–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Y S. M Tabatabaei, R Hosseini Tabata

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulfide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A ferrooxidans was used to change the surface chemistry of pyrite and copper sulfide ores and consequently, their flotation behaviour. In the presence of A ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulfide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria could be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50 per cent lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By S DeKruijff

The Mount Isa Mines Copper Mine in Mount Isa started producing copper in 1966. The Copper Mine gradually increased production rates to nearly six million tonnes per year. Over the last three years the mine has been in a gradual ramp down due to the reduction of primary ore sources and head grade. The majority of ore sources are predominantly in pillar retreat sequences bounded by multiple fill masses. There also a substantial lower grade resource delineated to the south of the main orebody. These remaining ore sources present significant engineering challenges to obtain a safe and cost-effective extraction. Stope designs have become increasingly complex and require additional engineering and operations input and analysis. This paper describes the major planning and operational challenges and issues associated with the stope design and extraction of an orebody in the later stages of mine life.

Jan 1, 2000

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

By B Yang, L Wang, C Y. Ng

Flotation process intensification is often achieved through changing chemical reagent scheme or flotation machine or both, which likely brings a hefty burden to the flotation plants in terms of capital or operating expenditure. A novel approach to flotation process intensification is the use of acoustic sound, which has been demonstrated to be effective in improving the flotation of various mineral systems with different type of flotation cells. This approach was based on the dynamic stabilisation effect of acoustic sound on the flotation froth. The present work aims to understand the influence of various experimental conditions on the effectiveness of the approach. First, the effects of sound frequency and amplitude were studied with column flotation of silica particles. Results showed that the flotation performance was improved only within a certain range of frequencies and above certain amplitude. The study was then extended to the mechanical flotation of quartz particles with various size ranges and at two solids concentrations. With sound, the recoveries of different size fractions within the range of 20–212 μm were all increased. In particular, the recovery of 150–212 µm particles was increased from 0 per cent to approximately 25 per cent, demonstrating the potential for extending the upper limit of particle size in flotation by using acoustic sound. Furthermore, mechanical flotation of chalcopyrite particles at various collector dosages (50–150 g/t) was carried out with and without sound. Results showed that the increment of the final flotation recovery was increased with sound at different collector dosages. Overall, acoustic sound has the potential to be used as an effective and versatile method for flotation process intensification.

Aug 24, 2022

By A Gibbs

Culture and leadership go hand in hand, especially when it comes to investing in safety. But the reality is that most safety leaders haven’t been taught the fundamental soft skills needed to lead effectively. In fact, only one in four safety leaders demonstrate effective skills and behaviours. Furthermore, when compared to its peers in other high-risk industries, our research indicates mining has the most room for improvement when it comes to effective safety leadership. In this presentation safety culture, climate and leadership will be outlined. Additionally, research data collected from our clients, across a variety of industries, will be shared to inspire reflection on the value of safety leadership. Finally, strategies to empower leaders and increase safety leadership behaviours will be described.

May 5, 2022

In the last several years we have seen the demise of the Department of Mining and Metallurgy at the University of Melbourne, the removal of extraction metallurgy from the Department of Metallurgy and incorporation of it within a School of Mines at the University of New South Wales, and the joining of a small Department of Metallurgy with a Department of Chemical Engineering to form a Department of Chemical and Materials Engineering at the University of Newcastle. Most of these changes have been forced by the logical application of the principles of accounting, the currency for such accounting being the Whole Student Unit (WSU). It is not my intent to address the problem of attracting young people into courses in metallurgy (including extraction metallurgy) which, at present, is the only way to introduce black ink into the WSU accounting ledger. Rather, I wish to express my disquiet over the trends, illustrated by some of the above occurrences, of separating out extractive metallurgy from METALLURGY by suggesting in broad terms how a course in metallurgy should be structured. I firmly believe that the mechanical metallurgist and materials engineer need an exposure to chemical and extractive metallurgy; similarly, the extractive and process metallurgist should, in my view, have a good grounding in the interrelationships between composition, structure, and properties, this topic being the core of the basic subject physical metallurgy.

Jan 1, 1987

By Q Zhou, H Nordberg, W Wang-Geissler

Efficiently controlling foam/froth within mineral processing continues to pose a challenge to the mining sector. The foaming characteristics of aqueous solutions for two-phase systems of air/liquid are well-studied with theories and mechanisms proposed to describe and predict foam formation and stability. The types and structures of reagents that either promote or prevent foaming/froth formation and stability are well-defined in these studies and practiced across various applications. Three-phase systems of air/liquid/solid, such as froth from mineral slurries, however, pose a challenge with the presence of a large quantity of relatively fine mineral particles. Theories and mechanisms that rationalise the effects of chemical additives as a defoamer or foaming agent in aqueous can be applied as a general rule, but do not provide the most effective solution for mineral slurry systems. Silicone-based defoamers, particularly their O/W emulsions, have been widely and successfully used at various stages of mineral processing to efficiently control the mineral slurry foaming properties. However, their foaming control ability could be significantly impacted by different processing aids used during the upstream process. In a zinc-rich mineral system, a silicone-based defoamer starts losing the properties necessary to effectively control foaming in the leaching circuit when throughput is increased. In this study, the synergistic defoaming/anti-foaming effects from surfactants and silicone-based defoamers are discussed to effectively control foaming/froth in the zinc leaching circuit, even with lower total defoamer dosage. Improvements during mineral processing can also lead to a cleaner mineral grade by reducing waste.

Aug 24, 2022

By Propser M, Szekely J

Flow maldistribution in the iron blast furnace has been studied analytically by the use of the vectorial form of the Ergun equation and experimentally via packed columns and a cold model of a blast furnace. Experimental results are presented showing the effect on fluid flow patterns of the following types of nonuniformities in a packed bed: the increased voidage at the wall ("wall effect"), the decreased voidage at the interface between layers of materials with different sizes and shapes, and the differences in resistance to flow of bulk regions of a column with different sizes and shapes. The proposed theory is applied to the calculation of fluid flow patterns for these nonuniformities. Velocity profiles, as calculated from these flow patterns, were found to agree reasonably well with experimental measurements obtained via hot wire anemometry techniques for laboratory scale packed columns. Calculated fluid flow patterns are presented for blast furnace burdens which show how flow patterns are affected by (a) coke segregation and (b) the relative differences in resistance to flow between coke and oxide pellet layers. For the cold model study, calculated flow patterns are presented based on photographs of a given burden distribution. The velocity profiles calculated from these flow patterns were found to agree reasonably well with the velocity profiles measured from the cold Model.

Jan 1, 1975

By Donchak PJ, Lang SC, Hammond RL, Bultitude RJ

The Hodgkinson and Broken River Provinces form the northern part of the Tasman Orogen. They are separated by a broad belt of Late Palaeozoic igneous rocks, but were probably originally continuous. They are bounded to the west by a system of major faults (Fig. 1) which separate them from the Georgetown Province. Although largely Precambrian, the Georgetown Province includes probable Siluro- Devonian granitoids, and in the south adjacent to the Broken River Province, metamorphosed Early Palaeozoic(?) volcanics and sediments of the Greenvale Subprovince. South of the Broken River Province, the Lolworth-Ravenswood Province includes probable Precambrian rocks, Cambro-Ordovician volcanics and sediments, and voluminous Ordovician to Early Devonian granitoids. The first systematic studies of the provinces were the 1:250 000 scale mapping programs by the Bureau of Mineral Resources and Geological Survey of Queensland (White, 1965; de Keyser and Lucas, 1968). These and subsequent regional studies were reviewed by Arnold and Fawckner (1980). Remapping by the Geological Survey of Queensland since 1982, and a concurrent regional study of the deformation by Hammond (1986) have provided much new data. We acknowledge the contribution of other members of the GSQ field parties - L. Cranfield, J. Domagala, B.G. Fordham, P. Green, R. Halfpenny, R. Hegarty, L. Hutton, S. Law, D. Macansh, T. McLennan and M. Scott.

Jan 1, 1987

Early in 1930 William S. Robinson, Managing Director of Zinc Corporation Ltd., anticipated a rise in the price of gold and a devaluation of the Australian currency. 'WS', as Robinson was known, formed a.syndicate in London, which later became incor- porated as Gold Mines of Australia Limited (GMA) to invest in gold mining properties in Australia. GMA examined many prospects and subsequently undertook the development of several mines in eastern Australia. The syndicate also held a number of options and several large reservations for gold exploration in Western Australia over which it was proposed to carry out an aerial survey and thorough scien- tific assessment. To do this Western Mining Corporation Limited (WMC) was incorporated in Melbourne on the 2nd March 1933. The founding chairman of WMC and GMA was the highly respected `Collins House' figure, Sir Colin Fraser. The aerial survey was carried out, and a group of eminent geol- ogists from Harvard University examined many prospects and identified several which warranted development. To finance these activities `WS' formed Gold Exploration and Finance Co. of Aus- tralia Ltd. (GEFCA), in London in July 1934. GEFCA ultimately held 95% of WMC and 62% of GMA. The finance came mostly from London based South African mining companies which had been subscribers to his earlier syndicate plus some American inves- tors. (The Group Structure in 1936 is shown in Appendix `B").

Jan 1, 1988

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By N Akizawa, A Tamura, S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Reaction products between high-temperature hydrothermal solution/uppermost mantle peridotite or lowermost crustal gabbro have been reported along Wadi Fizh of the northern Oman ophiolite; they are named as ‘mantle diopsidite’ and ‘crustal diopsidite’ respectively (Figure 1).The mantle diopsidite contains Cr-rich minerals like chromite, Cr-rich diopside (<2.5 wt per cent Cr2O3) and Cr-bearing grossular (<7.0 wt per cent Cr2O3). The chromites are varied in shape in the mantle diopsidite, euhedral to anhedral chromite grains contain globular inclusions of grossular and chlorite, and film-like chromite veinlets branch off from partially dissolved coarse chromite grains. In the crustal diopsidite, fine chromite grains are included in oscillatory-zoned skeletal uvarovite, especially in its high-Cr zones. The uvarovites are rich in rare earth elements (REEs). Direct laser ablation – inductively coupled plasma – mass spectrometer (LA-ICP-MS) analysis of the primary fluid inclusions detected Na, but not K.Our detailed studies of Wadi Fizh diopsidites clarify that the high-temperature hydrothermal solution dissolves chromite grains at the uppermost mantle section and precipitates hydrothermal chromite at the lowermost crust section. In addition, REEs were mobilised in the hydrothermal solution together with Cr. The hydrothermal solution involved in the diopsidite formation is assumed to have been rich in NaCl, and could mobilise appreciable amounts of Cr and REE.CITATION:Akizawa, N, Arai, S and Tamura, A, 2015. Chromium and rare earth elements mobility by sodium-bearing high-temperature hydrothermal solution – an example from mantle diopsidite and crustal diopsidite, in Proceedings PACRIM 2015 Congress, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E Hondros

Innovation and Business Skills Australia (IBSA) commissioned The Boston Consulting Group (BCG) to undertake a study into how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. This report builds on a previous study prepared by BCG in the early 1990s for the Industry Taskforce on Leadership and Management Skills (Karpin Committee), which provided a snapshot of the Senior Manager in 2010. The following powerpoint slides summarise the 2020 Vision û The Manager of the 21st Century û outlining how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. The presentation is summed up in the following quote from Jon Nicholson û Senior Vice President of BCG: We believe that to succeed in the years up to 2020, executives will need to master a range of hard and soft skills. Amongst other things, they will require to manage multi-generaional teams, the creativity to measure staff performance on outputs rather than inputs, and a high degree of technical and functional expertise in addition to their general management credentials. This paper is available as a PowerPoint presentation only.

Jan 1, 2006