Search Documents

A brief review of the problems in ventilating and cooling deep and hot Australian mines is presented. An overview is given on the development of the controlled partial recirculation concept. The main part of this paper describes the first majo

Jan 1, 1994

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

Mine site restoration, involving the re-establishment of original ecosystems, is a far greater challenge than revegetation, which simply aims to stabilise the site and to give it a green appearance. One of the challenges is to establish a simple yet effective measure of restoration success. A potentially useful approach is to focus on particular groups of plants or animals which are likely to provide a general indication of the state of the ecosystem in which they occur. Ants have been used extensively by the mining industry in this context, particularly in northern Australia. Ants are likely to be useful bioindicators because of their general importance in the Australian environment, and because of the many linkages they have with other parts of the ecosystem. Moreover, ant community structure responds to stress and disturbance in predictable ways, and therefore provides an interpretable measure of ecosystem change. This is illustrated by a study of ant recolonisation at Ranger uranium mine. However, the extent to which ants reflect the responses of other ecosystem components is poorly documented. This is currently the subject of a collaborative project between OSS and CSIRO.

Jan 1, 1994

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

By Taylor MN

The influx of an industrial environment into or adjacent to the indigenous society has in the past frequently caused the breakdown of traditional be- haviour and culture, and the generation of social and psychological impacts on the local population. Successful programmes developed by government agencies and private industry have been implemented in many areas to maintain the cultural environment and still afford the needs for industrial development. The ultimate goal of such programmes should be directed toward eventual operation and management of the established industry by the local population.

Jan 1, 1978

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

The equity market is now very much within a global village environ- ment, with various exchanges acting as agencies for the big casino. In this predicament, mining companies, who provide the most extensive, but relevant risk assessment information, will be best placed for favoured treatment by potential international investors: But what risk assessment information in summary form can be provided to support a resource/reserve statement? Even more importantly, does "objective" data exist, whose trends will support a resource/reserve state- ment? A prime need of the informed mining investor is to determine whether or not the resource/reserve statement is believable? But more importantly will it be realised? While the implications within the text of the majority of reports on resource/reserves suggests that the estimates are conservative, the record indicates that very few estimates are. In fact, to date, reports claiming to be conservative in respect of the overall grade estimate at a specfic cutoff have not reflected the realised grade at the stated cutoff; it has been more common for the realised grade to be lower than implied by the resource/reserve statement. Further, it is not uncommon for penalty elements to be understated and these components are rarely incorporated within resource/reserve statements.

Jan 1, 1988

By Taylor R. N

Flow simulations have been performed on the flash-smelting burners currently used at KNS. This paper presents studies of the heat transfer between gas and particles at the burner exit. Gas and particle temperatures, velocity and concentration profiles of the two-phase flow are calculated by the mathematical model. The predicted gas temperatures have been favourably compared against values measured by thermocouples placed near the burners in the flash furnace. The predicted particle temperatures are also reasonable when compared with the measured temperatures.

Jan 1, 1992

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

The purpose of this paper is to discuss briefly the problems encountered in designing and sinking No 7 shaft, and to present the methods employed in the operation.The illustrations accompanying the paper show the details of the construction of the equipment used in completing No 7 shaft, consequently the descriptions appearing in the text are brief outlines only. Mineral leases Nos 7 and 8, held by the Broken Hill South Limited, comprise an area of 69.5 acres. The length of the holding is approximately 2500 ft.The western orebodies, which are the main producing masses, enter the property at the northern bonndary. Generally, the dip of the orebody is to the west, and the pitch to the south, but local variations occur and even a reversal of pitch has been noticed. The angle of dip is approximately 70 degrees and the angle of pitch 45 degrees.

Jan 1, 1932

By Laing W. P

Sedimentary structures are described from the WiIlyama Complex, New South Wales. Their presence confirms lithological layering within the metasediments as bedding. These primary structures occur not only in low grade rocks as previously reported by other workers, but also in areas of medium and high grade metamorphism.Sedimentary structures include graded beds, cross beds, ripple marks, and ball and pillow structures.The observed parallelism of the early schistosity and bedding in the Broken Hill area has previously led to the idea of transposition by isoclinal folding.In the areas mapped, small scale transposition is precluded on the basis of1. uniform facing of sedimentary structures over wide areas, and2. the existence of large areas in which the early schistosity is oblique to bedding.

Jan 1, 1975

By Mutton B. K

Hilton Mine is being developed as an integrated component of the Mount Isa operation, to achieve continuity of silver/lead/zinc production well into the next century. The mine has a chequered history from its discovery in 1947 through several periods of intense development activity, each of which has been curtailed due to the further development of the Isa Mine operation. This era has now passed; to sustain increased production rates at Mount Isa, there is a requirement for Hilton ore in 1989. The decision was made in 1983 to accelerate the programme of Hilton development by installing skip hoisting facilities in the main service shaft (P49), to facilitate the development of the mine to pre-production status. The Hilton development plan provides for the mining of selected orebodies, a broadening of the underground exploration drilling programme, and the establishment of significant mine infrastructure. Several technical challenges have been identified as important. The Hilton orebodies, although occurring in the same rock type as Isa Mine, are more faulted, jointed and intersected by intrusive dykes. The ore is more variable in terms of ore continuity, boundaries, grade and metal distribution and the mineralogy more complex. As a consequence the development of this project consists of a co-ordinated programme of mine exploration and development, rock mechanics investigations and metallurgical research and development work. Production will commence in 1986 at a rate of 1000 t/day using mechanized cut and fill techniques. It is planned to introduce sublevel open stoping and by 1996/97 the production rate will be 2.5 million t/yr.

Jan 1, 1986

It is a privilege for me to participate in this vitally important discussion of The Role of Governments in the Management of Resources. The distinction of my fellow participants is evidence that this event is a matter of extreme importance and attracts international attention. In the management of natural resources, government and private enterprise share awesome responsibilities for the economic well-being of nations. Mining and its relation to the prosperity of nations is almost as old as recorded history. Copper was being mined and extractive metal- lurgy practised at Timna in Israel's southern desert as far back as 4000 B.C., and the rich mines of Laurium not only saved the Greeks from Persian domination 2500 years ago, but also provided Athens with a monopoly of silver in the Mediterranean world. This bolstered the economic power of Athens and led to the golden age of Greek commerce and culture.

Jan 1, 1978

By Mack JF

A metallurgical evaluation of the Argyle Kimberlite No. 1 (AKl) orebody has been carried out using a 40 tonnes per hour pilot plant. Pilot plant results, together with laboratory investigations provided a basis for the determination of process design criteria for a major treatment plant. Various sampling programmes were carried out to determine specific aspects in the evaluation of diamond liberation. Treatment parameters such as the top crush size, recrush size and the bottom cut-off size were investigated. A description of the pilot plant is given together with the design criteria for a 3 million tonne per annum treatment plant

Jan 1, 1984

Most text books on rock blasting claim that the relationship between burden and borehole diameter is linear. The statistical calculation presented here with real values from one hundred open pit and underground mines indicates that the relationship is exponential. For underground mines the burdens are consistently lower than those for open pit mines because of higher ore densities, greater confinement in blasting, and finally greater demand for well fragmented rock. The results shown in this paper are recommended to be considered in basic teaching of rock blasting technique. The formulas can be used for a first rough estimation of practical burden and spacing. The formulas do not however give any information about the fragmentation. For that purpose it is necessary to use other formulas not described in this paper.

Jan 1, 1990

By P Griffin

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway OperationsÆ 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007