Search Documents

In the process of mining the lower seam in a multi-seam operation, a lot of oblique fract- ures appeared in the upper seam which was in the equilibrium zone. These fractures closed soon after the lower face line passed. Despite the occurrance of some degree of undulations, and and step-like unevenness, the upper seam was subsequently extracted without difficulty. When attempting multi-seam extraction, from the height of the equilibrium zone, the minimum distance between seams in ascending mining should be predicted. By analysing roof con- vergences data and the geometrical configuration of subsidence profile, it was found that the minimum safe distance for ascending multi-seam mining depends on the mining height of the lower seam and the properties and structure of the inter-stratified rocks.

Jan 1, 1986

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Answers to many questions arising in the different phases of exploration, estimation and production of a mineral deposit, can be found in the geostatistical theory of G. Matheron. It is shown that all these questions regarding sample size, number of samples, shape of drilling pattern can be answered as soon as the continuity of the mineralization is quantitatively characterized by means of a variogram. Next a formula which gives the variance of the error associated to any estimation procedure (i.e., any method and any sampling pattern) is given. Applications to the computation of the standard error of the'mean for various sampling patterns are shown, as well as how to use the formula to simulate several possible sampling strategies and choose the best one. Altogether it is shown how to answer the often heard question, "what happens if such and such sampling procedure is used?", rather than giving an hypothetical "optimal" solution.

Jan 1, 1976

By Jagger ND

Pressure filters were found to be necessary to produce Elura silver/lead and zinc concentrates at sufficiently low moisture contents for bulk cargo shipment by sea to smelters.The difficulty in obtaining low moistures was due to the fine primary grind, 80% passing 45 microns, and resultant fine concentrates, 97% passing 45 microns.The filtration system was designed to filter up to 90,000 tonnes/year silver/lead concentrates and up to 130,000 tonnes/year zinc concentrates.This paper details the preliminary test work to select Larox automatic pressure filters, and the commissioning and operation of these filters to achieve design criteria for both concentrates. The design criteria for both concentrates have been bettered due to the concentrates being coarser than the design sizing.

Jan 1, 1985

By Ho E

Analyses of several nickel mattes from around the world show a significant variation in their copper content. Typically, matte contains an alloy, heazlewoodite and a copper sulphide phase. The various commercial methods of processing these mattes are reviewed and some of the fundamental factors which determine the choice of leaching system are discussed. Electrochemical studies on pure heazlewoodite and millerite in sulphate and chloride media are compared which show that nickel sulphides react via a series of nickel deficient sulphides and exhibit passivation as nickel is removed. Differences in the electrochemical behaviour of nickel sulphides in chloride media are attributed to greater crystallinity of sulphur and less formation of'NiS2. The electrochemistry of mattes differs because of the presence of alloy and copper. Copper in the matte modifies the potential for alloy dissolution and the rate of anodic dissolution of nickel. At elevated temperatures, Cu(II) in solution exchanges with NiS and completes the leaching of nickel at relatively low potentials without significant oxidation of sulphur to sulphate. It is concluded that there are fundamental advantages to leaching nickel matte in chloride media using Cu(II)/Clz as the oxidant.

Jan 1, 1996

A blast is designed to completely break competent rock such that it can be economically extracted, and efficiently handled or processed. Efficient breakage of the rock is critical to the success of an operation, and in many operations blast design is optimised to achieve fragmentation, muckpile profiles, and material that is easily excavated. There are inevitably other issues, such as damage to adjacent rock, that should be taken into account when designing a blast to achieve overall optimisation. Some of the key issues with respect to the integrity of the in situ materials adjacent to a blast are identified and briefly discussed in this paper. The potential for damage and the effects of a blast will be strongly influenced by the rock mass properties. This makes it important that site specific conditions and their response to blasting are known. Practical techniques that allow the disturbance adjacent to a blast to be measured with minimum disturbance to operations are described in the paper. Experience shows that, during the blasting process, there is considerable potential to disturb the in situ rock mass adjacent to the blast. In some circumstances a very important objective must be to minimise disturbance outside of the immediate blast area. Measured and observed disturbances caused by blasting to adjacent rock, for various common types of blasting, are discussed in this paper. Blast induced disturbances to the rock mass have been observed in both the near and far fields. These disturbances have the potential to impact on geotechnical design. The geotechnical significance of blast disturbance on a rock mass that is to remain in situ is explored and suggestions with respect to design are given.

Jan 1, 2004

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

By Nott M. C

The oxidation of xanthate collectors to xanthate/dixanthogen results in a higher hydrophobicity of sulphide minerals surfaces due to the action of dixanthogen. This higher hydrophobicity can be proved on a fundamental level by examining the st

Jan 1, 1994

Establishing the link between the solid, cold rock of dikes, sills, plutons, and lavas and hot, active magma chambers is the quest of igneous petrology. Differentiation of Earth, the diversity of the igneous rocks, and the spectacle of volcanism are ample evidence that magmatic processes are fundamental to our understanding of planet formation and evolution. Single gabbroic plutons, on the other hand, often show intricate and abundant evidence of the effects of crystal growth and sorting. It has not proven simple, however, to establish the basic principles of magmatic behavior leading to this crucial evidence. Because of their abundance, exposure, simple geometry, large range in size, and often straight-forward petrology, sills are excellent examples of the magma chambers. Physical and chemical processes operating in sills can be recognized that also routinely operate in many other bodies. Understanding the dynamics of sill solidification is essential to understanding the genetic links between lavas and plutons.

Jan 1, 1990

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

By Christie A. B, Swain A, Brathwaite R. L

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension. It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures, tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

The grinding of ore to a size that is conducive to the extraction of minerals by leaching or flotation is an essential and expensive component of most mineral-processing operations. Overgrinding results in reduced flotability of the minerals, as well as problems in the filtration and thickening processes, while undergrinding leads to a product in which the minerals have not been exposed, and cannot be leached or floated effectively. Furthermore, coarse material causes settling in thickeners and agitator tanks. It is therefore essential, from the perspective of both operational and extraction efficiency, to grind the ore to an optimum size fraction. A well-run milling circuit will yield a product within a narrow size band and at a high throughput. Although the effective operation and control of milling circuits with their many operating parameters is widely acknowledged as a complex as well as a critically important operation, the benefits of such control are difficult to quantify. This is due to the difficulties in relating more stable operation to increased recovery of the valuable components in downstream processes.

Jan 1, 1993

By Leung L, Downey M

This paper presents an overview of a technology package developed by BHP for locating discontinuities in coal seams using an in-seam seismic (ISS) exploration technique. The technology package includes instrumentation, data processing software, field procedures, numerical modelling and interpretation know-how. The technology developed has proved to be highly successful; features such as faults and dykes, not detected by other methods, have been delineated. Using equipment specifically designed for underground use, surveys are carried out quickly and at low cost. More than 30 ISS surveys have been conducted by BHP in Australia. Substantial savings in production revenue have been realised in situations where ISS has identified mining conditions which would have impeded longwall operations. Case studies of several ISS surveys are described in the Paper.

Jan 1, 1987

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrthotite/arsenopyrite concentrate, in order to describe the mineral- ogy, composition and surface area of the calcines. Sulfides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second, pyrite predominantly roasted via a pyrrhotite intermediate. Sulfur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, whilst having the greatest surface area, were the most refractory with respect to gold solubilization, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-micro- scopic gold in the second stage.

Jan 1, 1991

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

By Baczynski NR, Fagan MJ

A 3050m long section of a 1.65m internal diameter tunnel is presently under construction in the Brisbane area by means of the pipe-jacking method. The soils along the alignment had been deposited in a deltaic/estaurine environment and rapid changes in soil type occur. The tunnel passes beneath several extensive bodies of surface water. Groundwater problems have been experienced with tunnelling through alluvial sands and gravels. Details of the ground conditions, the pipe-jacking method used and tunnelling experience are discussed in this Paper.

Jan 1, 1987