Search Documents

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By T G. Vizcarra, T J. Napier-Munn, A T. Karbowiak, M G. Hart

Squeezing extra performance from existing equipment (‘sweating the assets’) is key to continuous improvement initiatives, particularly during times of cost cutting where the option of spending additional capital to facilitate circuit upgrades can be severely constrained. A common challenge, however, is identifying the best combination of settings for different process variables, as their effects can be camouflaged by interactions with other process variables and, of course, noise in historical data.This paper describes a recent investigation at Boyne Smelters Limited to identify strategies to coarsen the product of its dry, fixed-speed, open-circuit AG mill, without the need for installing pre-screens prior to the mill. The product is used as insulation material for the reduction of alumina to aluminium, and an excessively fine product was inhibiting the ability of the cover material to dissipate heat from the underlying anodes. The approach was to undertake a series of experiments, designed according to statistical criteria, to elucidate the effect of key process variables (feed blend and power draw) upon the product sizing. The results provided clarity about what strategies would encourage the production of a more desirable mill product (with some surprises). The study is a good example of how properly designed experiments can identify hidden potential in processing circuits, thereby mitigating the need for capital-intensive upgrades.CITATION:Vizcarra, T G, Hart, M G, Karbowiak, A T and Napier-Munn, T J, 2018. Getting the most from existing processes: using cleverly designed experiments to optimise the line 3 AG mill at Boyne Smelters Limited, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 207–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Safe, efficient production is a common objective for all large open pit mines. Despite comprehensive policies, procedures and regulations aimed at protecting workers, several people die each year in mining equipment-related collisions. The limited sightlines of heavy equipment operators coupled with difficult operating conditions are major contributing factors to the majority of mining equipment collisions. Off road haul trucks are the most common type of machinery involved in surface accidents. These vehicles represent the primary target for improving safety performance by mine operators. Although several commercial products have been introduced to address these issues, none have achieved significant market acceptance. The current collision avoidance solutions lack integration with onboard fleet management and equipment health systems. To achieve acceptance in industry, any collision avoidance system must offer high reliability, minimal false alarms, and value for money. With these criteria in mind, this paper will examine the pros and cons of the various technological approaches to collision avoidance in an open pit mining environment. The unique global positioning systems (GPS) and camera-based proximity detection solution on offer from Modular Mining Systems will be described. This solution uses intelligent filters to minimise false alarms. Tight integration with fleet management provides context information to enhance warnings and enable back-office near-miss analysis. Available today, this combination creates a practical solution to improve the situational awareness of heavy equipment operators, at a compelling price point. Future directions for maximising heavy equipment operator situational awareness will also be examined.

May 1, 2010

By A N. Kusnanto, D Sims, L Henim, S Crispin, J Hertrijana

The high sulfidation Purnama Au-Ag deposit located on the Indonesian island of Sumatra entered production in mid-2012 following a two-year program of construction and development. Discovered in 1997 following a regional stream sediment geochemical sampling program by the Normandy Anglo Asia joint venture, it is the first and largest deposit in G-Resource’s Martabe Project to enter production and is the centrepiece of a series of six deposits totalling 8.1 Moz Au and 73.8 Moz Ag in Mineral Resources (G-Resources, 2013a).In 2011 investigation into the controls of high-grade mineralisation in isolated parts of the deposit identified a potentially significant mineralisation style which had not been previously recognised or accommodated in the resource model. An extensive investigation of core and logging data followed to confirm the distribution of the somewhat unusual mineralisation style – a sedimentary-like cavity infill of very high-grade auriferous pyrite within the steep hydrothermal breccia feeders to the system. With the bulk of mineralisation located within the adjacent volcanic sequence and sandy-matrix phreatomagmatic breccia surrounding the feeders, the lack of constraint for high-grade intersections in the hydrothermal breccia zones had potential to significantly impact the mine plan in the lower sections of the planned pit through overestimation of local gold grade. Combined with new data emerging from grade control drilling and infill resource drilling in the pit, a program of reinterpretation of the deposit was initiated to update the geological and alteration framework underpinning the resource model. The result has improved the economics of the project and added metal to the Ore Reserve for Purnama.CITATION:Sims, D, Henim, L, Hertrijana, J, Kusnanto, A N and Crispin, S, 2014. Remodelling the Purnama deposit – an interpretation case study from G-Resources Martabe Project, Indonesia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C Paoletti

About 15 years ago the debate on the reliability of sampling procedures for agricultural food and feed commodities was initiated by a few brave scientists who questioned the representativeness of what, at the time, were routine sampling procedures established exclusively on the basis of tradition and practical feasibility. Over time several national and international organisations contributed to the discussion, developing standards and publishing papers either to underline the fact that sampling is always a source of error, in itself, which cannot be overlooked, or to minimise the relevance of sampling on the basis of argumentations linked to time and money limitations. The latter dominated, but is nevertheless impossible to accept from both a scientific and a responsible management perspective. Here the author presents an historical overview of these past 15 years, illustrating the most controversial issues, reporting major achievements in food/feed sampling, highlighting milestones, as well as unresolved problems that still need the attention and contribution from the sampling community. The need to incorporate Theory of Sampling (TOS) into food/feed safety assessment (pre-market), as well as into food/feed safety monitoring (post-market) has recently been highlighted, and the practical applicability of TOS to base food/feed safety decisions on representative sampling, has been explored and documented via concrete examples of risk analysis in different areas of food/feed industrial production chains. Now it is time to move forward and ensure that TOS is fully integrated into the well-established Food and Agriculture Organization (FAO) / World Health Organization (WHO) risk assessment approach, in order to guarantee a transparent and correct universal frame for risk assessment and the subsequent management decision-making process. WCSB8 offers the ideal platform to explore the best way to do so, switching from a theoretical discussion of correct sampling principles for food and feed agricultural commodities to practical recommendations in the interest of consumers, worldwide. These 15 years have also been a personal journey of interesting dimensions, indeed a veritable roller-coaster ride in-and-out of the scientific, technological, industrial and (last but not least) regulatory worlds. The start was WCSB2 in 2004, when I flew to Australia to discover if in other areas sampling had been identified as an unavoidable issue and, if so, what the solution was. There, I found a good travel companion who today is still on my side, to assemble the puzzle and explore how to shape the future, to concretely answer to the 15 years’ quest for proper sampling in the assessment and monitoring of food/feed safety.CITATION:Paoletti, C, 2017. Assessing and monitoring food and feed safety – a 15 year quest for proper sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 39–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By A M. Lechner, V Glenn, M Edraki, D R. Mulligan, C Unger

With more than 50 000 recorded abandoned mines in Australia, effective management strategies are needed to prioritise and manage health, safety, environmental and socio-economic risks and opportunities. This paper reviews international leading practices for abandoned mine management and identifies key issues that need to be addressed in the Australian context. As well as the academic literature, this review draws on a 2008 global legacy site survey and forum in 2008, a Churchill Fellowship study of abandoned mines and the recently released æStrategic Framework for Management of Abandoned Mines in the Minerals IndustryÆ (MCMPR/MCA, 2010).A conceptual model was developed to identify the relationship between key issues affecting the management of abandoned mines in Australia. The conceptual model is then used in the development of a maturity chart which draws on risk management principles to provide leading practice guidance for abandoned mine managers, jurisdictions and stakeholders. The maturity chart approach for risk management has been successfully used elsewhere to evaluate safety, environmental and socio-economic maturity.CITATION:Unger, C, Lechner, A M, Glenn, V, Edraki, M and Mulligan, D R, 2012. Mapping and prioritising rehabilitation of abandoned mines in Australia, in Proceedings Life-of-Mine 2012 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Monaghan, B S. Gregory

The Geita Gold Mine is located 80 km southwest of the town of Mwanza in the north-west of Tanzania and is 100 per cent owned by AngloGold Ashanti Limited. Open pit mining commenced at Geita in 2000. In 2011, the operation produced 494 000 oz at a cash cost of US$536/oz. This is a significant improvement from 2008, when 264 000 oz were produced at a cash cost of US$742/oz.A period of relatively poor operating performance at Geita was recorded over the period from 2006 to 2009. A period known at Geita as æthe turnaroundÆ commenced in 2009, and has been remarkable to say the least. Over the last couple of years the mine has embarked on a journey, which saw various interventions and initiatives. Among the key initiatives were Project ONE (which focuses on business process framework, systems for people and safety transformation), asset integrity, fatigue management and contract mining of satellite pits.Since the commencement of the turnaround at Geita, gold production has matched market guidance. The mine has returned to positive cash flow on the basis of strong performance on cash management, improved production and increased gold price.This paper explains some of the details of the mine operationsÆ improvements, how they were implemented, their relative contributions to improved mining performance and the path ahead to best practice. Observations will be made about some improvement rules that can be applied generally in open pit mining.CITATION:Gregory, B S and Monaghan, M, 2012. The path to best practice at Geita Gold Mine, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By A R. Bye, T R. Stacey

Anglo PlatinumÆs Potgietersrust Platinums (PPRust) operates three open pits and plans to excavate 90 Mt of rock in 2007. With pit slopes expected to reach a height of 400 m, the geotechnical department has a key role to play. Over the last four years PPRust has successfully implemented new geotechnical strategies and tactics to reduce risk, improve safety and maximise profitability. A large database of core logging, face mapping and rock testing data has been assembled and used for failure analysis, geotechnical zoning and rock mass ratings. The data has also been used for optimising blast designs on a daily basis through the use of a geotechnical block model. This greatly improves blast fragmentation and therefore loading and milling efficiencies. The slope design process involves limit equilibrium analysis, numerical modelling, rock fall analysis and block modelling. Slope management includes comprehensive limit blasting and visual inspections, and state-of-the-art slope monitoring equipment, namely the GroundProbe radar, Riegl lasers and GeoMoS automated prism monitoring. The risk-consequence approach has been used in slope optimisation, where all the slope analyses, operational controls, costs of failure, economic analyses of various slope designs and fault tree analyses are used to determine the ideal slope designs. These activities added over $25 million of value to the operation and also ensured compliance with Anglo AmericanÆs acceptable risk level. The successful mining of the optimised slopes is to due to the greatly improved geotechnical knowledge and slope management. PPRustÆs geotechnical work is used as a benchmark for Anglo American open pit operations. The focus of the paper will be on the value added to the operation by all aspects associated with slope management.

Jan 1, 2007