Search Documents

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

MR. L. C. BALL, chief government geologist, Queensland, wrote: This paper is intended as a severely mechanical exposition of the means adopted to deal with tremendous inflows of water concurrently with development and exploitation; but incidentally it serves as a splendid exposition of close co-operation maintained between the geological and engineering branches of this large organization.I have been impressed by the completeness of the mine plans of 'Mount Isa Mines Ltd.; but only such a paper as this has brought fully to my understanding the difficulty and complexity of the solid geometry involved in the detection and plotting of the orebodies and their stratigraphic control, including faults and large-scale brecciations, and the managerial foresight that set going the initial investigations.The company's geological branch of course must be given full credit for the results attained, but it gives me pleasure that the Geological Survey of Queensland has been closely associated in much of the study.It is noted that complete drainage was affected, but it would be interesting to learn whether the brecciated zone will again become waterlogged and whether from above or from below, and whether there has been any change in the dissolved mineral content of the water as the work progressed.

Jan 1, 1939

By Bradley AJ

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By S Van Duin, I Porter

This paper discusses how advanced manufacturing technology (AMT), which is fundamentally reliant on and developed via multi-disciplinary skills, has benefitted non-mining industries, and what lessons can be derived from this experience to benefit the mining industry, particularly underground coal mining. Examples of AMT use in æconventionalÆ industry, some drawn from the more than 25 years experience in many different industries of the Automation and Robotics team at the University of Wollongong, are described to show typical benefits, risks and opportunities expected in using AMT. Applying AMT to mining brings many unique challenges and this paper expands on these and then provides practical examples of how a multi-disciplinary team can develop new processes and systems leading to productivity, safety and other benefits for underground coal mining.

Sep 26, 2011

The Department of Mineral Resources is the lead agency in mine site environment management and control in New South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.

Jan 1, 1995

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

By L J. Strachan, O J. Hawes, S W. Crossen, R C. Roberts

The Albany Conglomerate is a widespread geological unit found in northern areas of Auckland, New Zealand. It has previously been described as part of the early Miocene Waitemata Group which underlies most of Auckland. Much of the Waitemata Group comprises weak interbedded sandstones and mudstones, but also includes conspicuous conglomeratic units such as the Albany Conglomerate. The Albany Conglomerate comprises a well-cemented mixture of hard pebbles, cobbles and boulders of igneous and metamorphic derivation in lenticular beds. A number of tunnelling projects are planned for the near future in Auckland. Recent experience has shown that the variable features associated with the Albany Conglomerate can make selecting appropriate construction methods very challenging. This paper explores the engineering geological and sedimentological features of the Albany Conglomerate with respect to other conglomerates within the Waitemata Group and the potential implications on tunnelling projects in Auckland. Consideration is given to the extent of proposed geotechnical investigations and the production of geotechnical baseline reports.CITATION:Roberts, R C, Hawes, O J, Crossen, S W and Strachan, L J, 2014. Underground construction challenges associated with the Albany Conglomerate in Auckland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 195–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By X Ma

Kaolinite is of very fine particle size in nature and thus its dispersion plays a key role in the successful removal of kaolinite in iron ore flotation and selective flocculation processes. As the most widely used dispersant in the world, sodium silicate has been used as a standard dispersant for kaolinite in the iron ore industry. However, the actual effect of sodium silicate on the colloid stability of kaolinite particles and its dispersion mechanism remain unknown in the literature. In this work, the dispersion effect and dispersion mechanisms of some common inorganic and organic dispersants, including sodium silicate, polyphosphate and a low molecular weight polyacrylic acid, on kaolinite particles were systematically investigated through electrophoretic mobility and colloidal stability studies over a wide pH range. It was found that sodium silicate-kaolinite interactions only take place in the neutral and acidic pH range, while polyacrylic acid and polyphosphate interact with kaolinite from pH 3 to 10.5. Consequently, sodium silicate only disperses kaolinite at neutral and acidic pH. In contrast, polyacrylic acid and polyphosphate disperse kaolinite from pH 3 to 10.5, with strong dispersion effect observed at neutral and acidic pH. In the iron ore industry, selective fl occulation and reverse cationic fl otation, the most widely used flotation route, are both conducted at pH 10 to 10.5. The results of the present study show that, at such high pH, polyacrylic acid and polyphosphate are more effective dispersants of kaolinite, in comparison with sodium silicate.

Jul 11, 2011

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Boshoff, D Reid

It has been recognised worldwide that the liquefaction risk of unconstrained tailings stacks or cyclone underflow embankments requires careful consideration. The stability of a tailings deposit where the perimeter embankments are made up of hydraulic fill is often governed by post-liquefaction stability.Cyclones are frequently used around the world to classify tailings into a coarse underflow for building a tailings impoundment wall and a finer fraction that is disposed of into the basin. The shear strength of the tailings that form the outer embankment of a tailings storage facility (TSF) and the location of the phreatic surface are the two most significant factors influencing the structural integrity of the facility. The coarse underflow is placed in such a way as to contain the overflow, which is finer, has low strength and is often poorly consolidated.A cyclone field trial was undertaken at a gold mine in Western Australia to assess the feasibility of using the cyclone deposition method to optimise and increase the capacity of an existing tailings cell. The aim of the cyclone trial was to collect information to demonstrate to the client and the regulators that cyclone deposition was a feasible option for raising TSF embankments. The cyclone trial provided an opportunity to assess the cyclone under field conditions and the quantity and quality of the underflow fraction produced on-site. A variety of methods were used to assess the flow liquefaction susceptibility of the tailings underflow sample produced during the cyclone field trial.The field trial, laboratory testing and analysis will be discussed in this paper.CITATION:Boshoff, J and Reid, D, 2015. The resistance of cyclone underflow material to flow liquefaction, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015