Search Documents

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By E. I. Larsen, E. F. Swazy, F. R. Hensel

EXPERIENCE has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. TEST MATERIALS Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It was found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended on the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as one eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from. 900°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal composition was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical properties and certain bearing properties of this alloy are described in the present paper. PREPARATION OF COMPACTS Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition: 25 per cent nickel; 7 silicon; 3 phosphorus; 64 copper. This alloy is brittle in. the cast condition and can be readily powdered. SINTERING PROCEDURE The blended powders were pressed at 25 to 40 tons per sq. in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By K. S. Lane

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse. VAIONT RESERVOIR SLIDE Fig. 1 shows Vaiont Dam in Italy which is a double curvature arch, 875 ft high, located on a tributary of the Piave River, north and west of Venice. When completed in 1960 it was the highest arch dam in the world. In 1960 a sizable landslide (some 700,000 cu yd) occurred on the left abutment a short distance above the dam. Following this, the reservoir was held down for construction of a by-pass tunnel through the right valley wall to insure connection with the upper end of the reservoir in event of further slides. In October 1963 a giant landslide occurred on the left valley wall, over a width of some 14 miles (see Fig. 2). Over 300 million cu yd slid into the reservoir, displacing the water and forming a hige wave 700 ft above the top of the dam as it hit the opposite, or right, wall of the valley. The wave then passed some 500 ft over top of the dam, followed down the tortuous winding canyon and debouched into the

Jan 1, 1967

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

There were two official representatives of Foreign Governments as guests at the Chicago Meeting. One was Frederick Goransson, managing director of the Saudvikens Steel Works, who represented the Jernkonteret, the Iron and Steel In-stitute of Sweden, and who came to this country especially for our meeting. The other distinguished guest was Commander Toublet, who repre-sented the French Embassy. Commander Toublet delivered a most polished address at the Banquet, dealing with the felicitous relations existing between this country and France for the last 150 years. Com-mander Toublet was accompanied by Mrs. Toublet, who won the hearts of all the ladies present, whose guest she was.

Jan 11, 1919

By Hermann Bach, Walther Hänig, Willi Gehrhardt, Ernst Theurich, Walter Langner

With the construction of the Magdeburg zinc works, the Georg von Giesche's Erben Mining Co. of Breslau has to a certain extent completed the program of reconstruction which it set as its goal after the boundaries of Upper Silesia were drawn by the Treaty of Versailles. During its history, covering.more than two centuries, zinc and lead mining has been its chief activity. Through the new boundaries established, it lost to Poland all its mines and smelters, including five distillation smelters. Of its extensive properties, there remained only an apparently unimportant and unexplored portion of the old Bleischarley ore field which, however, happily made possible the resumption of its old business. In 1925 the Deutsch-Bleischarley shaft-only a few kilometers from the old Bleischarley shaft—was sunk and developed, and in May 1926 production of lead and zinc ore was resumed. As facilities for smelting were lacking, the ore was at first delivered to the neighboring smelters, which had now become Polish. Realization of the plan to build its own zinc works had to be postponed at first for lack of capital. In the meantime, however, plans for the new works were worked out in all details. After extensive experimentation in a semicommercial pilot plant it was decided, at the end of 1928 and the beginning of 1929, to use the electrolytic process and, for economic reasons, to place the works at Magdeburg. With zinc at the approximate price level that had ruled since the Deutsch-Bleischarley mine had begun working, it was hoped that the plan could be completed in 1930 with the company's own resources. However, falling metal prices, already noticeable in 1929, made this impossible, and further postponement for a time became necessary. Finally, at the end of July 1933, the funds for building the works became available, in the form of a loan granted under the first employment

Jan 1, 1937

By L. C. Glenn

IN the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. OIL IN TENNESSEE A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about. 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were producers. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that

Jan 1, 1920

By V. F. Zackay, J. F. Carlson

CURRENT experimental work on the development of gas turbine engines in the automobile industry has emphasized the need for a relatively low cost nonstrategic castable alloy for service in the 1200" to 1400°F temperature range. Ferritic steels

Jan 1, 1956

By C. K. McArthur

THE subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years passed have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1937

By O. U. Bradley

The methods of handling the oil output of the Mid-Continent fields are not unlike those practised in other oil fields of the United States, and it is not expected that this paper will present any entirely novel ideas. Some features of the practice of handling this oil may be of interest, however. Wooden Gaging Tanks Practically all of the oil sold to pipe line? and other purchasing agencies throughout the Mid-Continent field is gaged from wooden tanks. Steel gaging tanks are slowly coming into use, and are preferable in many ways—leakage and evaporation are reduced, and the strapping and recalculation of capacities are unnecessary. The wooden tanks are slightly coned to facilitate tightening the hoops. The sizes in common use are 250, 500, 800 and 1600 bbl. The number and the capacity of the gaging tanks upon any producing oil property depend upon its production, and the facilities for disposing of the output. The 1600-bbl. size was the most common in the Cushing field, particularly during the period of flush production. The tanks are distributed over the leased premises in groups of two, three, and four tanks each, and these are filled from flow tanks, or through direct pipe connections with the heads of the wells. Flow tanks are merely temporary reservoirs to facilitate the transfer of oil from the wells to the gaging tanks. They diminish fire risk, and are considered indispensable on small producing properties where water is pumped with the oil, as they permit the refuse and water to 'settle out before the production is run to the gaging tanks. strapping and Calculations After a gaging tank has been strapped (measured) and its contents computed, a deduction of 3 per cent. is made from its computed volume. The strapping of a tank requires four steps: (1) The outer circumferences

Jan 1, 1920

By F. M. Lewis, J. F. Myers

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By J. F. Myers, F. M. Lewis

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969