Search Documents

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By G. B. Misra

Though resistance to flow offered by mine airways supported with timber sets has been an object of study over the last half century, no accurate relation has yet been established from which prediction of the resistance coefficient of a projected timbered airway can be made. Zenofontowa et al. developed an empirical relation, but this relation has not been found to satisfactorily correlate experimental data obtained by Sales and Hinsley. This led the author to develop a set of simple theoretical relations between the resistance coefficient of timbered airways and the various parameters affecting it, such as the type and spacing of sets as well as the shape and size of members forming the set. Experiments were designed with the help of a laboratory model airway to verify the validity of the relations developed. With the experiments conducted so far with 4, 3 and 1-piece sets of 3.4 x 3.4, 2..5 x 2.5, and 4.5 X 4.5-cm square-section timbers in a 45.8 x 38-cm model airway, the theoretical relations have been shown to hold.

Jan 1, 1972

By Harlowe Hardinqe

ABOUT three years ago a distinctive new type of crushing and grinding equipment, known as the Hadsel mill, was announced. A description appeared in the November, 1932, issue of this magazine. Any machine that would take run-of-mine ore and reduce it, in one operation, and at a reasonable cost, to a size suitable for metallurgical treatment was bound to attract much interest, as the original Hadsel mill did. The first commercial sizes were built with the drum supported by an overhung shaft and partly immersed in a tank. The drum carried inside and outside buckets to lift the ore, which was dropped as the drum revolved onto stationary breaker plates projecting into the drum from the opposite tank wall. The coarser material settled back into the inside buckets. Intermediate sizes were carried into the tank, and this material was scooped out by the outside buckets and deposited hack in the drum for further grinding. The fines were carried out of the mill with the wash water over an adjustable weir at one side of the tank.

Jan 1, 1935

By Walter A. Backofen, Donald H. Avery

Intense primary and cross-slip traces were observed in easy glide on Cu: 6 pct-A1 single crystals deformed in tension. A mechanism of cooperative source operation is developed which recognizes that both the applied stress and that resolved from dislocation arrays contribute to the stress on a source. By considering the stress from arrays, the activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals are explained. Furthermore the cross-slip system is predicted to be second favored during easy glide for a large range of orientations. FROM many studies of easy glide in fcc metal crystals, a pattern of observations has developed which still requires full explanation. In pure copper, aluminum, and silver, the easy-glide, slip traces are fine and uniform with steps 50 to 100A on the primary* system.1-4 Yet it has not been at all clear why slip in the pure materials should occur in this way. On the contrary, one might expect, with simple slip and a low hardening rate, that the weakest sources on the primary system would operate extensively to produce strong slip traces. In a brass, however, intense slip steps up to 0.5 are found on both primary and cross-slip system4,6-9 seeger10 has pointed out that in a material of low stacking-fault energy such as a brass, extensive easy-glide cross-slip could not be thermally activated, but rather must originate on the cross-slip plane. In further explanation, the wilsdorfs4 and seeger10 noted that only the cross-slip system would not harden differently than the primary, whatever the latent hardening tendencies of other systems; therefore, in brass, which exhibits high latent hardening, the cross-slip is the only secondary system which could be expected to operate extensively, once it became active. The explanation of how the cross-slip system, on which the applied stress is low, becomes activated has been related, in a nonspecific way, to pileups by Hirsch11 and Honeycombe.l2 In the work to be described, deformation traces on solid-solution Cu: 6 pct A1 single crvstals were studied with conventional light microscopy and a mechanism proposed to explain both the observed activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals. EXPERIMENTAL In preparing the Cu-A1 single crystals, rectangular bars approximately 0.4 in. by 0.4 in. by 6 in. were first machined from ingots made by vacuum melting copper of 99.999 pct and aluminum of 99.99 pct purity. They were then packed in powdered graphite and the crystals grown in a modified Bridgman apparatus at a rate of 5 mm per hr under an atmosphere of purified nitrogen. Crystal perfection as indicated by Laue back-reflection spots was good except for the last inch to freeze, which was discarded. Orientations so determined are shown in Fig. 1. Tensile specimens with a reduced gage section were obtained by masking the ends with electrical tape and chemically polishing in a solution of 20 pct HNO3, 24 pct HAc, 52 pct H3PO4, 2 pct Hcl, and 2 pct H20 at room temperature.13 Finally, the specimens were electropolished in a 30 pct ortho-phosphoric acid bath at 12 v. Tensile deformation was performed in an Instron testing machine at a strain rate of approximately 1 pct per min. During easy glide, extensive cross-slip was observed with all crystals, in spite of the low Schmid factor on this system, and in no case was any other secondary trace encountered. A certain sequence of slip-line development was associated with the extension. At yielding, intense primary traces passing completely through the crystal developed at some point on the gage section, generally near the grips; weak cross-slip traces also appeared, extending from the primary traces into the adjacent undeformed crystal, Fig. 2. Further extension led to primary traces adjacent to the first-formed and connecting with those of the cross-

Jan 1, 1963

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART 1.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust.

Jan 1, 1929

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By Erwin L. Zodrow

A geological model of the modes of formation of magnetite and its distribution in the Smallwood iron-ore mine, Labrador, Newfoundland, is given, based on observation and geological mapping. This is called the conceptual model. If mathematical expressions plus probabilistic uncertainty are used to represent the conceptual model, then this is termed a mathematical model. The purpose of this paper is to test if there exists a correspondence between the conceptual model and two related mathematical models (called factor analysis). Details of the statistical technique are given. The results of factor analyses in relation to the magnetite formations in the Smallwood mine are discussed. Several practical mine applications are presented. The difficulty of maintaining quality control over ore mined from any deposit naturally depends on geological conditions; these are usually imperfectly known to concerned mining geologists. One geological condition that would greatly facilitate ore predictions is if a relationship between the observed ore particle distribution* and its mode of origin could be demonstrated. Such a casual interrelationship is normally sought through the application of well-defined geochemical principles of primary mineralization in given geological environments. However, the application of conventional tools of geological research, including geochemistry, to areas that have undergone repeated periods of geological deformation and metamorphism subsequent to primary mineralization becomes rather difficult. More important, the interpretation of such research results are nearly impossible on an objective basis. Mineral assemblages may have been reworked and changed due to tectonic influences to the extent that the present-day observable mineralogy and ore-particle distribution can effectively obscure the mode of origin of the ore. Quantitative measurements, based on petrological investigation of mineral assemblages, reflect the sum-total of all geological influences. Which of several influences had the most effect on existing ore particle distribution is difficult to assess, for these influences can neither be measured directly nor quantified by petro-logical logical or geochemical means. The present study is concerned with the magnetite distribution and its modes of origin within the Small- wood mine,' located in the southern extension of the Labrador geosyncline; see Fig. 1. This geosyncline is thought to have undergone at least two periods of geo-tonic tectonic deformation, separated in time, since the fer-rugenous rugenous sediments were deposited." Detailed geological observations and mappings (1 in. to 40 ft) have highlighted subtle, distinctive features of the magnetite distribution in the Smallwood mine: (1) The magnetite is generally concentrated in bands or layers within this ore body; these bands alternate with specularite-rich bands and quartz bands. The banded or layered nature is common in Precambrian iron-ore deposits, and this has been interpreted as a result of changes in depositional environments. (2) The grain size of the magnetite varies; near the contacts between the iron and quartz-carbonate formations, the magnetite occurs as well-crystallized octa-hedra. In areas of intense folding, magnetite is extremely fine grained and concentrated in bands and occurs in association with earthy manganese minerals. (3) Magnetite tends to be more highly concentrated near the geological contacts of the iron and quartz-carbonate formation in the northeast part of this mine, Figs. 2, 3, and 4. (4) Magnetite is also fine grained and tends to higher concentration near and parallel to fold axes; however, in this case, the ore is much softer than given in item 2. (5) Magnetite mineralization decreases along strike and away from the areas of intense folding, i.e., towards the approximate center of the mine, Fig. 3. How can these variations of magnetite be explained on a geological basis? We can postulate a conceptual model that the distribution of magnetite appears to be related to three basic geological influences: (1) geo-tectonics, i.e., concentrations of magnetite near geological contacts of the iron and quartz-carbonate formations, the fine-grained nature of magnetite and its higher concentrations near fold axes, and decrease of magnetite towards the approximate center of the mine; (2) secondary alterations, i.e., variation of grain size of magnetite near the iron and quartz-carbonate contacts, and in areas of intense folding where magnetite occurs together with earthy manganese minerals: (3) original

Jan 1, 1971

By Goldye Leeds, Marian Balicki

A SURVEY of literature reveals the scarcity of experimental evidence relating to work hardening and reannealing of silver.'-'" With the exception of the well-known X-ray investigation of silver and other metals by W. A. Wood? the effect of progressive cold working has not been studied. The determination of thermal stability of silver in the work-hardened state by means of isochronal or isothermal annealing has been confined apparently to very high reductions only. In the survey made, no study was encountered which endeavored to produce a complete picture of the changes in various properties due to cold working and subsequent reannealing. To fill these gaps and to assemble data that could be used for the determination of activation energies and of frequency coefficients of primary recrystallization, a systematic experimental approach, which was developed by one of the authors, has been applied to pure silver. Material and Processing The silver used was Handy and Harman fine silver, with a spectroscopic analysis at the testing stage of Cu, 0.0001 to 0.001 pct; Te, 0.0001; Pb, Si, Ca, Mg, and Mn, traces. The material was supplied in the form of a rod 0.406 in. diam and was converted into test samples according to the procedure condensed in Table I. It should be mentioned that air annealing was adopted to simulate industrial practice, though it was realized that annealing in a neutral gas or in a vacuum would be preferred. The usual precautions have been taken to eliminate any structural changes and property changes resulting from the storage of the samples prior to annealing or testing. Thus the wires were kept at the fully annealed stage, and the final wire drawing, which produced the desired degree of work hardening, was done just prior to the final annealing or testing. During the short waiting period, the samples were kept in a thermosflask filled with ice. Even with these precautions some strain-age-hardening or self-annealing could occur. To test such a possibility, wires of different reductions were prepared in the manner adopted and portions of them were immediately tested. The remaining portions were similiarly tested after different periods of storage, both at room and melting-ice temperature. Within experimental error, all samples obtained from a wire of a given percentage of reduction yielded identical values. This result qualified the material for further tests and interpretations, because it showed that either strain-age-hardening and self-annealing were absent, or that these effects fully balanced each other. The final annealing was carried out in an electric resistance furnace automatically controlled to within a 10°F. It was realized that the temperature fluctuations were greater than desired for this type of work. TO diminish the errors due to fluctuations of temperature, the hot junction of the thermocouple was placed as close to the samples as possible; the time of soaking was reduced to 15 min; and the number of samples annealed at different temperatures was increased. It will be seen from Table I that some tests were performed on the same material at rising temperature. These will be discussed elsewhere. Room temperature testing was limited to the determination of some of the mechanical properties that are known to be additive in a degree sufficient to be used for indirect study of the kinetics of the reannealing process, Tensile tests, carried out on a manually operated J. Camillon machine, accurate to within permitted the determination of the ultimate stress (U.S.1 and of the 2 in. elongation, (A,). The proof stress (d,e) has been determined from a series of bend tests carried out on a Tinius Olsen Stiffness Tester by using the offset method. This involved accurate determination for each sample of load-angular deflection curves, finding a

Jan 1, 1952

By D. L. Passmore, J. D. Bennett

The degree of injury and days lost from work due to an injury are examined for selected electrical sources, occurring in conjunction with falls of the injured miner or with selected machinery, that could have been eliminated by use of diesel equipment. Although the number of preventable electrical source injuries is small relative to the total number of injuries during the period examined, many lost-time injuries could have been precluded and thousands of days lost from work could have been avoided.

Jan 1, 1986

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By P. G. Shewman, T. L. Wilson

Using published surface-diffusion (D,) data and published sintering equations, it is shouln that surface difusion should dominate the neck-growth stage of intering for all materials in which D, has been measured (six metals and A1as). Also, grain boundary diffusion can be expected to contribute appreciably to shrinkage and possibly to neck growth below some critical temperature of the order of 70 pct 01- the absolute melting temperatuve. In view of the widespread conclusion in previous sintering work that volume diffusion dowzinates neck gvowth, experiments were conducted using spherical copper powders to test this conclusion. Scaling studies on neck growth at 950°and 1020°C clearly demonstrated that suyface diffusion dorninates. Kinetic studies on shrinkage gave more equivocal results that indicated an increasing role of' grain boundary transport at lower temperatures. Five diarszeters from 100 to 300 u were used in the scaling sludy and a temperature range of -650' 10 950 C was covered in the shrinkage studies. All experiments were conducted in dvy hydrogen. In 1949, Kuczynski published his now classic paper on the determination of the transport mechanism in sintering from the time laws of neck growth. In the interim, these laws have been applied to many systems and slightly modified by several authors. Essentially all these authors concluded that, for crystal- line materials, the dominant transport mechanism in neck growth is volume diffusion. This stems from the observation that the neck radius increases about as t"5 and that the activation energy approximates that for lattice diffusion. A related but independent series of studies stems from Mullins' rigorous analysis of the growth of the groove formed where a grain boundary meets a free surface." xperimental work stemming from this analysis has shown that for each crystalline material studied (Au, Ag, Cu, Ni, Fe, Pt, Al2O3) surface diffusion was clearly the dominant transport mechanism for groove widths up to the order 10 to 20 p. The ratio of the quantity of material being carried by lattice diffusion to that carried by surface diffusion increases linearly with the groove width, so surface diffusion is dominant for all widths under 10 to 20 u. The analysis of the relative contributions of surface and volume diffusion to grain boundary grooving, and to neck growth in sintering, shows that they are quite similar. Thus, using the available surface-diffusion data and the approximate equations of Kuczynski, or the more rigorous recent equations of Nichols and Mullins, 3 it can be shown that the small necks between particles must grow almost entirely by surface diffusion. The purpose of this study was to re-examine the basis for the conclusion that the neck-growth stage of sintering proceeds by volume diffusion. Using spherical copper powders, of several different diameters, precise experimental measurements were made of both neck growth and shrinkage. Application of Herring's scaling laws to the neck-growth data clearly indicated that neck growth occurred by surface transport, even though the neck radius increased as or Using the recent analysis of Mullins and Nichols as well as published data on surface diffusion, it is shown that the observed time law, as well as actual rate of neck growth, can be satisfactorily explained by a surface-diffusion mechanism.

Jan 1, 1967

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.' Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By Clarence P. Linville

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By T. D. McKinley

Theory, operational characteristics, and indicated precision and accuracy of analytical methods based on vacuum extraction, equilibrium pressure, and combustion approaches are reviewed. At the present time vacuum extraction at 1400°C and the equilibrium pressure method are recommended for determination of hydrogen in titanium and titanium-rich alloys. UNTIL a few years ago the role of hydrogen in titanium was an unknown factor with regard to its effect on the physical and mechanical properties of the metal. However, following the work of Jaffee and othersa-" it is now generally acknowledged that hydrogen has a degrading effect on titanium and its alloys. The chief manifestations are a decrease in impact strength in -systems and delayed cracking in a-ß systems. Since hydrogen does have a de- grading effect on titanium it is essential to control it within tolerable limits. It then follows that procedures for quantitative estimation of hydrogen are a primary requirement for the industry. For greatest benefit these methods should be simple, rapid, and precise. In addition to having these virtues, methods must be easy to duplicate in both equipment and technique to gain widespread use. After inherent accuracy has been established, the, required precision to make a method acceptable is dependent largely on the nature of the work at hand. Ability to obtain a representative sample has a pro-

Jan 1, 1959

By Fred C. Bond

THEM is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determinations of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.' Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.' For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969