Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By M. B. Riordan

A surface indicating pressure, temperature and flow instrument that ernploys variable frequency sensing elements has proved useful in evaluating flow characteristics of wells. Relative productivity of individual oil and gas sands in a given well can be analyzed at several back pressures. The variable frequency sensing elements are an improvement in sensitivity and accuracy and make possible observation of temperature and pressure variations that have not been possible heretofore. The surface indicating featuere results in a more direct approach to solving problems and eliniinate; many assumptions. All three subsurface factors are evaluated, and correlation between them results in a direct means of analyzing reservoir. and well conditions. Surveys have been used to evaluate well performance. locate gas entry In high ratio wells and to investigate gas injection and water flooding conditions. INTRODUCTION In a flowing well that is open to a multiple number of producing sands with varying characteristics. it is valuable to know which sands are producing fluid at a given back pressure and in what relative quantity. Core studies could qualify an interval as productive, and reserves would be computed on this basis. Unless the well is produced so that the interval does contribute. irreparable damage to the interval can occur. It is generally accepted that the optimum condition of pro-

Jan 1, 1951

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper describes the field opeturluns at the Fry in situ combustion project in Crawford County, 111. Field operations may be divided into three phases—-preliminary engineering studies of 1960 and 1961, ignition, and, finally, operation of the test. The Fry combustion project was a pilot test of cocur-rent in situ combustion on a 3.3-acre inverted five-spot. In the summer of 1960, air injection tests were conducted using old wells in the area and a new air injection well drilled especially for the test. In the summer of 1961, four new oil wells were drilled on a 3.3-acre pattern for the pilot test. All old wells in the near vicinity of the pilot test were abandoned to preclude any possibility of gas escaping to adjacent formations. A compressor plant was also installed at the test site in 1961. Air injection tests and other engineering studies were made. At the conclusion of these tests, ignition was accomplished with a 40 kw electrical igniter. Operation of the Fry combustion test was little different from the usual oilfield operation with the exception of the high rate of air injection. No difficulty was found with the openhole completion. There were no unusual corrosion or emulsion problems until bottom-hole temperatures exceeded 150F. Four cores were drilled into the burned-out portion of the reservoir with no mechanical difficulties. INTRODUCTION A cocurrent or conventional in situ combustion test was conducted on the Fry unit of the Marathon Oil Co., in Crawford County, Ill. Besides testing combustion in the Fry type of reservoir, the test was intended to evaluate various operating procedures. This paper presents a discussion of the Fry combustion test field operations. The geology of the reservoir and the test performance are discussed in other papers.'.' HISTORY OF THE FRY UNIT The Fry unit consists of 11 leases totaling 337 acres in an area in which oil was originally discovered in 1906. Production from this reservoir, as from all Robinson sand reservoirs in the area, was very high during the first few years. As the dissolved-gas energy was dissipated, early attempts to retard the decline consisted of vacuum, air, and gas repressuring, and recently, most of the area has been subjected to water flooding. Following early air repressuring, the Fry waterflood unit was formed and water flooding initiated in July, 1952. In the area in which the Fry combustion test was conducted, a peripheral water flood of a 160-acre area was developed as shown in Fig. 1. Between 1956 and 1960, it became apparent that the water flood was unsuccessfd. In looking for a suitable site for an in situ combustion test, the Marathon Oil Co. selected the Fry unit as possessing those features most desirable for such a research project. Field operations associated with the Fry combustion test began in the spring of 1960.

Jan 1, 1966

By George S. Rice

MANY studies on ground movement and subsidence have been carried on by members of the Institute during the past year, but only a few papers have reached maturity. Two of the mining schools of this country have continued their interest in ground movement research. At Columbia University School of Mines, Philip Bucky has continued his investigations, employing photoelastic methods and the use of his centrifugal apparatus for testing what he termed "the strength and behavior of mining structures." Helmut Landsberg, of The Pennsylvania State College, has developed a convergence recorder similar in principle to that used by the

Jan 1, 1936

By R. J. Wasilewski

The variation of elastic modulus with terrzperature between -150° and 600°C has been investigated. Compounds close to equiatomic cornposition exhibit very low modulus values and very high damping near room temperature. The modulus rises steeply with both decreasing and increasing temperature. The modulus minimum and the high damping are believed to be connected with a martensitic transformation of TiNi. In bulk material this transition takes place slightly above room temperature quite rapidly and reversibly, with a hysteresis of some 30°C, depending on the Ti:Ni ratio. Oxygen impurity affects the reaction time. THE inter metallic compound TiNi has been reported to exist in an ordered CsCl (B2) structure,l-6 the homogeneity range varying rather markedly with temperature.7 Some investigators reported this compound to decompose peritectoidally to Ti2Ni and TiNi, between 650° and 800°C,3 or below,',g the latter workers also suggesting the decomposition to be strain-sensitive. Purdy and Parr were the first to report a structural transformation to a new, possibly hexagonal, structure at 36°C,7 a temperature indubitably too low to allow the significant amount of diffusion necessary for a peritectoid reaction. Mechanical-property investigations of compositions close to TiNi just above room temperature have qualitatively shown remarkable anomalies, particularly with respect to clamping,' and to a "memory" effect, that is, plastically deformed material returning to its original shape on being heated through the "decomposition" temperature.9 The original explanation of this effect—based on the apparent experimental observation of Ti2Ni or TiNi, formation in the material subjected to tensile or compressive stresses, respectivelp—does not appear plausible. It appeared more probable that the change involved may be a martensitic, diffusionless structural transformation, similar to those observed in other B2 structures such as 0 brass,'' AuCd,ll and AuZn.12 The existence of such transformation has been established recently,', although the symmetry of the low-temperature structure is not yet known. The present paper describes the elastic modulus and damping behavior of polycrystalline TiNi in both structures. EXPERIMENTAL METHOD 1) Specimens. All the specimens to be investigated were prepared from premelted electrolytic nickel and iodide titanium by nonconsumable arc melting and casting in a water-cooled copper mold. The cast billets were canned in mild steel, extruded, and swaged to approximately 0.375 in. diam. The cans were then removed by pickling or machining. Preliminary material balance checks indicated no significant weight losses on melting (less than 5 mg on a 50-g button); hence nominal compositions have been used throughout. In agreement with previously reported observations7 no single-phase material was obtained at—or close to—Ti 1.00 Ni1.00 a small amount of finely divided second phase always being present. It was found that most of the oxygen impurity was associated with this minor phase, which was identified as oxygen-bearing Ti2Ni—possibly Ti,Ni,O. The amount of this phase—at any given Ti:Ni composi-

Jan 1, 1965

By Leonard Waldo

PROBABLY some of the views advanced in this paper will appear, from a metallurgical standpoint, little less than revolutionary. It is with considerable hesitancy that I venture to offer a few thoughts concerning what, seems to me to be perhaps the most important development of metallurgy since the introduction of Bessemer steel. Dr. John Percy, with that rare insight which characterizes the epoch-making man, described in a communication to the Royal Society, about 1855, an alloy of duminum and copper which he called aluminum-bronze. The name has "stuck." The term "bronze" has been so variously used that I confess I do not know exactly what constitutes a bronze; but I know that in the great materials of engineering simplicity of composition is a cardinal excellence; and I wish to venture the suggestion that aluminum-bronze is not an alloy of aluminum and copper in any such sense as the compounds of tin and zinc with copper (except the copper-tin compound SnCn3) are alloys. There are several reasons which lead me to this view. In the first place, if a series of bars be prepared containing varying percentages of aluminum and copper, and the electrical conductivity of these bars be carefully determined, a curve of conductivity will be obtained, as shown in Fig. 1, which represents the result of such experiments. While I am not sure, at this time, that the values of conductivity shown in this diagram are wholly dependent upon the percentage of aluminum added, the assumption is a probable one; and the curve indicates that an extremely small percentage of aluminum affects the conductivity in a ratio out of all proportion to the amount of that metal. Another reason is drawn directly from experience in the foundry. If we take from the furnace a crucible containing melted aluminum and one containing melted copper, both at a little more than a red heat, and pour them together, the reaction is so intense that the

Jan 1, 1895

By O. D. Gonzalez, H. A. Wriedt

Alloys ranging from pure iron to pure nickel were saturated with nitrogen gas at 918°, 999°, and 1217°C and analyzed. The solubility of nitrogen at 1-atm pressure was obtained as a function of nickel content for the whole range of iron-nickel alloys and the temperature dependence of solubility is shown for the experimental alloy compositions. The heat of solution and the entropy of solution of nitrogen in the alloys as func-tiom of composition up to 41 pct Ni are given. 1 HE acquisition of more exact thermodynamic information for systems composed of iron with various alloying elements continues to interest ferrous metallurgists. The interstitial alloying elements, especially carbon, hydrogen, and nitrogen, comprise a field of particularly intense study. A recent investigation of carbon solubility in Fe-Ni alloys held at 1000°C in gases of fixed carbon activity showed an unpredicted minimum in the solubility near 72 pct Ni.1 The present investigation was undertaken to see if a similar anomaly in solubility existed for nitrogen in Fe-Ni alloys. The solubility of nitrogen in ? iron at known nitrogen activities has been measured several times.&apos;-&apos; Corresponding information for the solubility of nitrogen in solid Ni and Fe-Ni alloys is not available. Juza and sachsze9 reported that metallic nickel dissolved 0.07 pct N in equilibrium with Ni3N at 445°C. This result was regarded as dubious by Turkdogan and Ignatowicz10 who found less than 0.0004 pct N in nickel specimens equilibrated at 600°C with ammonia-hydrogen mixtures having fugacities of N2 gas up to 35,000 atm. Such fragmentary reports indicate only that nitrogen gas has a very much lower solubility in nickel than in iron. MATERIALS A purified iron from Battelle Memorial Institute was used for solubility measurements. This grade contained more than 99.95 pct Fe, the highest content of any measured individual impurity being 50 ppm for each of As, C, Cu, and Pb. The nickel and iron-nickel alloys, supplied by the International Nickel Co., contained 0.02 to 0.04 pct C, 0.17 to 0.19 pct Mn, 0.04 to 0.08 pct Si, < 0.01 pct P, <0.03 pct S, and <0.20 pct Co as principal impurities. The Fe-0.59 pct Mn alloy was of zone-melted quality, the highest concentration of any individual impurity being 15 ppm Al. The "prepurified" grade of nitrogen gas from Matheson Co. had a nominal nitrogen content of 99.996 pct. An "electrolytic" grade of hydrogen gas from National Cylinder Gas. CO. in which the principal impurity is water vapor was admixed with the nitrogen to prevent oxidation of these specimens. This grade was preferred to a purer grade because the presence of some oxygen helps in suppressing contamination of the specimens, for instance, by silicon from the porcelain furnace tube. EXPERIMENTAL PROCEDURE The specimens were equilibrated in vertical tube furnaces through which a 99 pct N2-1 pct H2 gas was passed at ambient pressure. For the 915", 918", and 999°C runs, a wound-resistance furnace was used, and for the 1217°C runs, a furnace with a tubular silicon carbide element was used. The temperature control system on both furnaces was similar: a Weston "Celectray" controller with a modulator, responding to the electromotive force of a thermocouple with its hot junction in the furnace, switched the furnace current between high and low settings. The temperature distributions in the working zones of the furnaces were determined with calibrated Pt/Pt-10 pct Rh thermocouples. The overall uncertainty in temperature was estimated to be ±3° at 915° to 999°C and ±5° at 1217°C . Consideration of the small temperature coefficients of the equilibria studied, together with the error limits in the method of analyzing for nitrogen, showed that further refinement in temperature uniformity would give no improvement in resultant accuracy. The reactive gas was generated by mixing together "prepurified" nitrogen and "electrolytic" hydrogen directly from cylinders commercially supplied. The flow rates of nitrogen and of hydrogen were fixed by setting with bleeders the pressure drops across the individual calibrated flow meters of constant resistance. For any given alloy, the solubility of nitrogen at 1-atm pressure (% N) was obtained from the analyzed nitrogen content of equilibrated specimens (% Na)according to Sieverts&apos; law, thus

Jan 1, 1962

By R. J. Charles

PREVIOUS study&apos; of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the wack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object. In the case of a low velocity impact, at an energy level equal to that of a high velocity impact that causes fracture, loading rate would be relatively

Jan 1, 1957

By N. J. Grant, D. Carne, J. B. Seabrook

IT is unnecessary to review much of the literature on hydrogen embrittlement of steel since several excellent reviews and bibliographies exist.1-3 Hot acid pickling and cathodic charging have been known to cause hydrogen embrittlement of steel and have been used as laboratory methods to charge steels with hydrogen.4-8 Experimental Procedure The problem of prime concern in all instances, except in the work of Sims and coworkers,10 is that at no time was there a definite known hydrogen value reported which could be related to a particular value of the degree of embrittlement. It was the purpose of this research to determine the relationship between hydrogen content and degree of em-brittlement quantitatively. The 1020 stock used for the specimens was hot-rolled 7/16 in. diam rod of the following analysis: 0.19 pct C, 0.40 pct Mn, 0.012 pct P, 0.036 pct S&apos; Vacuum-fusion analyses for nitrogen and oxygen gave 0.014 pct O2 and 0.0011 pct N2. Cathodic charging was used to cause embrittle-ment. The advantages of this method were that no quenching was necessary, the impregnation was reasonably controllable, and representative samples for analysis could be prepared simultaneously with the charging of the tensile bars. Analyses for hydrogen were made in a vacuum-fusion type of apparatus which extracted gas from the samples by fusion in a molten tin-iron bath&apos; This apparatus, which has recently been described in detail elsewhere, will not be discussed here.". " Consecutive samples can be analyzed every 15 min with an accuracy of 0&apos;03 ppm. A A from an electrolytic or pickling bath can be charged for analysis in about 3 min, and analysis completed in 15 min. Samples of as-received 1020 stock were analyzed and found to contain a negligible amount of hydrogen (0.06 ppm). Preliminary pickling and electrolytic charging gave highly variable results. Cold-worked samples showed higher values but ranged from 0.6 to 6.0 ppm of hydrogen. Charging at 90°C gave higher values of charged hydrogen, but troublesome films on many of the specimens resulted. It was not until a few drops of a catalytic poison, prepared from 2 g of yellow phosphorus dissolved in 40 ml of carbon disulphide,8 was added to the electrolytic cell that fairly consistent high values of hydrogen could be charged into the as-received 1020 steel at room temperature. The cell used is sketched in fig. 1. The anode and fixture for the tensile specimens were fastened to the cell cover as shown, and the specimen was screwed in place, centrally located with respect to the anode. At first, anodes of lead and graphite were tried, but they contaminated the electrolyte and gave a slight deposit on the specimen. Later, a platinum wire was used in the form of a uniform helix. A current of 2 amp, corresponding to about 0.5 amp per sq in. of cathode, was used for most specimens. The electrolyte was 4 pct H2SO4 solution. Fig. 1 shows the form of the special tensile bar, the main portion of which was an ordinary 1/4 in. diam, 1 in. gauge length test bar, except that two to four small cylinders of stock were left attached by small links to the bottom end of the tensile bar for the purpose of providing samples for hydrogen analysis. Thus the bars and samples were charged with hydrogen simultaneously and an analysis could be made while the bar was being tested mechanically. Experiments were performed to determine how representative the test cylinders were of the middle of the test bar proper. While the bar center was being analyzed, the small cylinder was stored in dry ice, since it had been shown that such storage prevents loss of hydrogen for many hours.12 The results of these checks are shown in table 1. The checks are very good (0.3 ppm) and indicate that it is permissible to use the small end cylinders to establish the hydrogen content of the tensile test bar proper-

Jan 1, 1951

By R. Adair, W. R. Hudspeth, W. T. McDaniel

A NEW method for concentrating the flake mica either from present washing plant tailings or from new feed has been developed. In this paper, flake mica refers to that which occurs in weathered granites, alaskites, pegmatites, and schists in a form too fine to be considered sheet mica. It ranges in size from 1 in. or more down to 200-mesh or finer and occurs with kaolin, quartz, and partially kaolinized feldspar. Scrap mica, a term often used indiscriminately to describe everything other than sheet mica, will be used to denote the waste product from sheet mica mines and fabricating plants. Both flake and scrap mica are used in the mica grinding plants to produce wet-ground or dry-ground mica, although some flake mica recovered from clay mining operations is fine enough to be marketed without grinding.

Jan 3, 1951

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

By C. D. Hunter, J. B. Browning

During the year 1934, Kentucky oil and gas operators have partly overcome their past depression fears and in the oil industry, with possibly more abandonments of old oil producers than the completion of new oil wells, produced 4,814,904 bbl. of oil in 1934 against 4,501,511 bbl. in 1933. In the gas industry of eastern Kentucky, 115 gas wells were completed during 1934. This production is delivered through two 20-in., one 16-in., one 12-in., one 10-in., and two 8-in. pipe lines to supply both domestic and industrial markets in Cincinnati, Ohio; Louisville, Lexington, Frankfort, Winchester, Ashland, Covington and other Kentucky towns; Washington, D.C., and other eastern cities. The largest percentage of these gas wells and production are from the Devonian black shale area of Floyd, Pike, Knott, Martin and Magoffin counties, Kentucky. In this area the largest percentage of 1889 wells, developing 421,-215 acres, has been completed in the past 10 years, of which 55.3 per cent produce from the 400 to 550 ft. of Carbonaceous Devonian black shales. The successful results obtained from these Devonian shales are due to the physical effects of the 5000 to 6000 lb. of gelatinated nitroglycerin with which the entire 400 to 550 ft. of shale is shot. A very small number of the shale wells are natural producers and do not require shooting. Other than the Devonian shale gas production, the remaining 44.5 per cent of the gas in this field is encountered throughout the entire strati-graphic section above this horizon; namely, salt sands of Pennsylvanian age and Maxon, Big Lime and Weir of Mississippian Age. A very small percentage is encountered in the Corniferous Devonian lime and the Silurian Big 6 below the black shales. In western Kentucky, in the counties of Henderson, Webster, Hopkins, McLean, Christian, Muhlenburg, Ohio, Daviess, Hancock, Brecken-ridge, Hart, Barren and Warren, many gas wells have been completed, but, because of insufficient market, activity has been somewhat desultory. The area is served by the pipe lilies of the Kentucky Natural Gas Corporation, with headquarters at Owensboro. Their market is increasing and the gas is delivered to Owensboro, Henderson, Madisonville, and many

Jan 1, 1935

By Heath B. Fowler

The surface mining operations of the Simplot Fertilizer Co. are on the Fort Hall Indian Reservation approximately 16 miles east of Fort Hall, Idaho (Fig 1). The Phosphoria formation outcrops in sec. 2, 3, 11, 14, 15, 22 and 27, T 4 S, R 37 E, Boise Meridian. The ownership of these phosphate-bearing lands is divided between individual Indians and the Bannock-Shoshone Tribe, and the royalties are paid to the respective owners on a tonnage basis, as the rock is mined. The geology and mineral resources of the Fort Hall Reservation were studied by the U. S. Geological Survey in 1913 and reported on in 1920. † However, it was not until the winter of 1945 that exploratory work was undertaken by private enterprise. Diamond drilling was begun by the Simplot Fertilizer Co. in April 1946, and stripping operations were started in June. A camp was established near

Jan 1, 1950

By P. K. Foh, C. G. Dunn

IN an investigation of the rolling and recrystalliz-ing textures obtained from single crystals of Si-Fe, Koh and Dunn included specimens in the (111) [lie] orientation.1,2 This note reports some additional results obtained on samples of this orientation set aside for further study. After, primary recrystallization longer annealing treatments at 980°C produced only normal grain growth; after 16 hr at 980°C the largest grains were approximately 0.010 to 0.020 in. in diam. The orientations of 13 of the larger grains were found by the transmission Laue method. The unidentified (110) poles of these grains have been added to the (110) pole figure obtained after primary recrystallization2 to give the plot shown in Fig. 1. When grain identifications are also included, such a plot reveals the following. Two orientations agree almost exactly with the peak pole ,density positions of component B of the primary recrystallization texture, one with component A, and one with component C. All the remaining orientations except one have (110) poles near weaker and unidentified pole density peaks. In fact, the correlation is good enough for an identification of eight components. Previously only components A, B, and C were certain. The results are perhaps even more informative when combined with the (110) pole figure of the cold-rolled crystal to give the plot shown in Fig. 2. Each of the 13 orientations is identified and uniquely determined by selecting two (110) poles per crystal, which are 90" apart. The plot shows that every grain of the 13, except grain 6, has a (110) pole in common with a (110) pole concentration of the cold-rolled crystal. The orientation relationship with the cold-rolled orientation may be expressed as approximately 25" rotations about <110> axes, which is in agreement with the results found for coarse-grained primary recrystallization.2 If primary recrystallization had occurred according to the <110> rule without preference, there would have been 12 components. Actually our limited data reveals nine of the possible 12. The integrated pole figure also shows preferences among them, since three are considerably stronger than the rest. In addition to the above direct information, the following conclusions may be drawn. Primary recrystallization of the (111) [110] cold-rolled crystal produces a limited number of weak and strong components with the larger than average primary grains from these components related to the cold-rolled crystal by 25° <110> relationships. In arriving at this conclusion of limited orientations the (111) [110] orientation has to be ruled out as a source of large primaries for two reasons. First, growth in this orientation was not observed, despite an expected high grain boundary mobility (due to its 25" <110> relationship with every component of the texture). Secondly, primary recrystallization usually produces grains in new orientations, particularly in a single orientation matrix; but (111) [110] is not new. Other orientations besides those of the <110> type may be considered unlikely, of course, because the <110> relationship holds quite well for primary recrystallization2 and should produce the large primaries. There are exceptions to this rule, but probably not enough to provide large

Jan 1, 1958

By R. G. Robins

The processing of gold bearing sulphide minerals which contain arsenopyrite and various complex arsenic sulphides results in arsenic containing emissions and effluents which are suspect in relation to clean air and clean water standards. Removal of arsenic from gaseous emissions is briefly reviewed. The use of lime to stabilise aqueous residues as either calcium arsenate or calcium arsenite is shown to be inadequate for long term disposal since both compounds are converted into calcium carbonate due to the influence of carbon dioxide in the atmosphere. Mixed calcium arsenate-phosphate residues are similarly unstable, but present better stability than the straight calcium compounds. Alternative disposal methods are reviewed whereby the arsenic is converted to more stable compounds, such as barium arsenate, titanium (IV) arsenate, and arsenic sulphide.

Jan 1, 1984

By L. E. Porter

El Segundo field is about 14 miles southwest of the central portion of the city of Los Angeles, immediately adjacent to the town of El Segundo and the Standard Oil Company&apos;s El Segundo refinery site. The field is served and bisected by several major highways connecting the beach cities on the west side of the Los Angeles Basin. The exact location of the field and its position with respect to other producing areas is shown on the map covering this portion of the Basin (Fig. I). The Republic Petroleum Co. discovered the first commercial production in the area when it completed its El Segundo No. 1 (sec. 18, T. 3 S. R. 14 W.) at a depth of 7402 ft. on Aug. 24, 1935, flowing at the rate of about 400 bbl. per day, 28" gravity oil. The producing horizon in this well consists of about 72 ft. of conglomerate and schist conglomerate situated below the nodular shale (Miocene). The true (or solid) schist (Franciscan) was encountered and penetrated some 20 ft. in the bottom of the hole. This paper gives a report on the history of development and oil production to date, and also submits the writer&apos;s interpretation of structural conditions as determined from such development. The limited development, together with the complex and variable nature of the producing horizon, makes any interpretation of the structure at present only tentative, and any forecast for a given well extremely hazardous. History of Oil and Gas Production The El Segundo field has produced approximately 1,920,000 bbl. of oil. It has 27 producing wells and 14 drilling wells or locations. The present daily rate of production is about 13,400 bbl. The production history of the field to date is shown in Table 1. The principal companies operating or owning leases in this field are: Caminol Company, Geo. F. Getty, Inc., Ohio Oil Co., Republic Petroleum Co., Pacific Western Oil Corporation, Royalty Service Corporation, Richfield Oil Corporation, Standard Oil Company of California, The Texas Company, Union Oil Company.

Jan 1, 1938

By Charles Burrows

THE burden a man can endure depends on its magnitude and the number of tunes it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude f the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary stresses. While we are unable to formulate the law between the magnitude f repeated stresses necessary to produce rupture and the length of time during which these alternating stress may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which, to a first approximation, is exponential. In other words, F = Ce-t where F = magnitude f alternating stresses; = time for which stresses are continued; C = constant, which&apos; depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics f any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 6, 1921

By John M. Bostwick

Bitumen is a general term for a group of materials composed of mixtures of hydrocarbons that are fusible and soluble in carbon disulfide. Included in the group are petroleum, asphalts, asphaltites, and mineral waxes. Asphalt is a dark-colored, cementitious solid or semisolid, which generally softens on heating and resumes a more viscous or solid state when cooled (personal communication). It is found in native form in fissures and pore spaces in rocks and as lakes. It is also obtained from the residues produced in petroleum refining. Asphaltites are black, naturally occurring solid bitumens. They are generally shiny and break with a conchoidal fracture. Common asphaltites are gilsonite (uintahite), grahamite, and glance pitch. Mineral waxes are solid or semisolid, relatively nonvolatile bitumens of various colors, having an unctuous feel and waxy luster. Of the native waxes, ozokerite is the best known. Montan wax is also classed as a natural wax, although it never occurs in the pure state and must be extracted from lignite or cannel coal (Ladoo, 1920). Mineral waxes may also be obtained by pyroprocessing of petroleum, lignite, and peat. Pyrobitumens are dark-colored, solid hydro- carbons that are infusible and relatively insoluble in carbon disulfide. They are so-called because they will yield liquid and gaseous hydrocarbons only when heated. Asphaltic pyrobitumens are defined as "substantially free of oxygenated bodies" and include wurtzilite (elaterite), albertite, and impsonite (Thrush, 1968). Nonasphaltic pyrobitumens contain oxygenated bodies; examples are coal and peat. The nonasphaltic type will not be discussed further. Petroleum Asphalts Asphalts refined from crude petroleum have almost completely replaced the native types. Refineries can produce asphalts in every desirable grade more economically and in greater quantity than the native types and with a variety of properties that meet the requirements of the various manufacturers using them. For all practical purposes, it is estimated that more than 95% of the asphalts consumed in the United States are refined from crude petroleum (private communication).

Jan 1, 1975