Search Documents

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

Diffusion in Solid Metals. BY ROBERT F MEHL (Institute of Metals Division Lecture Tech Pub 726 in Metals Tech, Aug , also Trans, vol 122 22,500 words ) Diffusion in solid metals constitutes one of the important fundamental phenomena in metallurgical behavior Apart from its obvious importance in processes such as chromizing, carburizing, nitriding and calorizing, it plays an important part in the processes of homogenization, age-hardening, and transformations in steel, its scientific importance is no less great Diffusion may occur within a grain, along a grain boundary, or upon a surface, though the exact and even the relative values of these separate processes are known for only a very few cases The requirement of solid solution formation presents the possibility of identifying solid solution phases by a study of diffusion layers Some distortion accompanies diffusion, leading to little¬ understood grain-size changes Distortion assists diffusion though usually it dis¬appears before diffusion has become extensive In a binary system the rate of diffusion is the more rapid in the lower melting metal Many of the published data are too qualitative to permit sound scientific conclusions Age-hardening data may be treated as diffusion data and rates of reaction in steel could profitably be studied from this point of view Studies on diffusion are of great importance to the develop-

Jan 1, 1937

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940's it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By S. Oglesby, A. L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are not immediately available at the time the sample is taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily corre-

Jan 1, 1960

By R. C. Philp, Allan Gibb

The term a matte " is applied to smelting-products so extremely diverse in composition and physical properties that it appears impossible to devise any generic formula to represent, chemically, the manner in which the varied proportions of the almost unlimited possible constituents combine with each other. Mattes produced in copper-smelting, in distinction from those produced in smelting-operations in which the recovery of cop per is secondary to that of other metals, cover a narrower range in composition. The copper-content of such mattes vary from 20 to 80 per cent., and even this range is much smaller in general practice since it is found advantageous, when possible, to produce mattes with about 50 per cent. of copper in the first operation. Further, it is unusual that arsenic or antimony occurs in copper-ores in sufficient proportions to form arsenides or antimonides in such quantities that they will separate out from the furnace-products, as is common in lead-smelting. Generally, the mattes produced in copper-smelting are composed mainly of copper (usually greater than 35 per cent.), iron and sulphur, the remaining elements being usually in proportions sufficiently small to allow of their treatment as impuritiee, rather than as essential constituents of the mattes. In modern practice of smelting copper-ores in blast-furnaces the tendency is to approach pyritic smelting as nearly as possible, the furnaces being low and the air supplied being largely in excess of that required for complete combustion of the carbonaceous fuel. Hence, the atmosphere of the blast-furnace thus used is usually oxidizing or nearly neutral, and, as a consequence, the reduction of metallic iron that was a necessary evil of former practice is of unusual occurrence in operations where the main object is the recovery of copper. Hearth-accre-

Jan 1, 1906

By E. B. Ekren, F. C. Frischknecht

Recently released results of surveys employing the slingram and turam methods show the applicability of electrornagnetics in mapping new areas containing both oxidized and unoxidized iron in the Lake Superior region.

Jan 10, 1961

By Mark Malamphy

THE occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltic petroleum first directed attention to the Sao Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a con-siderable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geo-physical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area.

Jan 1, 1936

By J. J. Bailey, R. C. Dean

Dr. Maurer has reviewed the large and confused field of rock mechanics and drilling. We have focused our attention on advance drilling and the disengagement of rock. To understand drilling in greater detail is certainly desirable, but such understanding does not necessarily hold any certain promise of near-term practical advancement. In the longer term, it is probably essential. Present work on drilling and our understanding of drilling falls roughly into three separate classes (and, indeed, these are in no way peculiar to drilling): 1) we have knowledge of certain (scientific) topics which seem to be relevant to the process, 2) we have knowledge of the drilling process in both qualitative and quantitative terms from observation of the actual process, and 3) we have certain modeling procedures, by which we bridge the gap between these two previous areas. The usefulness of our scientific knowledge depends critically upon this last item. In all our following remarks we shall consider only those problems of drilling and the disengagement of rock in which the rock behavior is essentially brittle. Let us start by examining some of the problems of constructing an even moderately detailed theoretical model of the drilling process in the small. The prospects of any near-term success in that direction seem extremely meagre; nor is it clear that any great advancement in the practical art of drilling is even likely to result from the construction of such a detailed model. On the other hand, as we shall suggest later, considera-

Jan 1, 1967

By James Marsh

INTRODUCTION Economists have long expressed suspicion of the economic theory of natural resource exhaustion, even in writing articles which have contributed to it (1). Indeed, the gap which separates the pure theory from practical management seems unusually wide. It is doubtful whether a mine manager could possibly know enough about the relevant parameters of his mine to steer it along the optimal paths described by the theorists (2). Nevertheless, enough faith in the theory remains that mine managers are suspected of being a separate breed whose behavior must be studied in special courses using specialized text-books, collections of readings, and journals (3). The implied hypothesis, that mines and natural resource firms are managed differently than other firms, is the subject of this paper. In the next section the theory is developed and analyzed. In section III, I discuss the implications of the statistical results that have been obtained. Finally, conclusions are reserved for section IV. THE MODEL A key difference between the traditional theory of natural resource production and that of other forms lies in the set of variables which ire assumed to jointly determine the quantity of output the firm will produce. Output, in the non-resource case, is assumed to be a function of k clearly definable and distinguishable inputs or factors of production, viz., y = f(xl, x2, ..., xk), (1) here

Jan 1, 1977

By Alberto J. Terrones L.

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,1 by Barrel1 on Marysville, Mont.,2 and by Goldschmitt on the Oslo district, Norway,3 laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf4 made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control5 ore finding. Some years later Harrison Schmitt6 fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed.

Jan 3, 1958

By Marius R. Campbell

Every mining engineer who has engaged in prospecting for coal in flat-lying rocks understands the importance of constructing geological sections across the territory which he has to prospect. If the area is small and the time and means at his command are unlimited, he can construct such sections with the transit and level; but if the area is great and the examination hurried, as it frequently is, he will doubtless be puzzled how to proceed. Under this pressure of time and means, his work will probably be, to a great extent, devoid of any system, being simply a hap-hazard opening of such seams as show in outcrop at some point on the territory, without any determination of geologic structure or stratigraphic succession. Prospecting carried on in this manner is never satisfactory to the intelligent mining engineer, for he must realize that the information which he is able to furnish to his employer is totally inadequate to determine the economic value of the property. To the owner of the land such a report is no more satisfactory than to the engineer. Unless the latter can show both

Jan 1, 1897

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,' on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By Max W. Ball

An intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies which tend to. confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. Origin of the Law Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb.11, 1897(29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims.' . The immediate cause for the passage of this Act was stated in a brief report in the, House of Representatives (there was no debate in the Senate) to be a decision of the Department rendered Aug. 27, 1896 (Union Oil Co., 23 L. D., 223), directing the cancellation of an oil placer entry on the ground that land containing petroleum cannot be located and entered as a placer mine. The report of the Public Lands Committee of the House contains the following interesting statements Congressional Record, vol. xxix, p. 1409):

Jan 1, 1915

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By Leo Tarasov

MAGNETIC torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade1,2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time 1.5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction, or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements.

Jan 1, 1939

By Eugene A. Stephenson

In most instances the fluids produced from underground reservoirs have been described as they appear at the surface, and usually it has not been necessary to distinguish between surface and reservoir phases. More recently it has become imperative to recognize the fact that changes in phase may occur between the reservoir and the receiving unit. The simple terminology of "wet" and "dry" gases and "crude petroleum oil" served our needs fairly well in the shallow, low-temperature and low-pressure fields. It has been left to the legislatures, regulatory commissions, and courts to decide whether a field is or was a gas field, an oil field, or both. This they have done by direct definition and also by implication. For example, in Texas:' (d) The term "gas well" is any well (a) which produces natural gas not associated or blended with crude petroleum oil at the time of production, or (b) which produces more than one hundred thousand (100,000) cubic feet of natural gas to each barrel of crude petroleum oil from the same producing horizon, or (c) which produces natural gas from a formation or producing horizon productive of gas only encountered in a well bore through which crude petroleum oil is also produced through the inside of another string of casing. (e) The term "oil well" is any well which produces one (1) barrel or more of crude petroleum oil to each one hundred thousand (100,000) cubic feet of natural gas. In the state of Louisiana, the same general result is achieved largely by the following paragraph :* Wells producing both oil and gas shall not waste or blow into the air an amount of gas of more value at three cents per thousand cubic feet, than the market value of the oil recovered. The Commissioner of Conservation shall allow a reasonable time to determine the status of any well. This means that for wells making both oil and gas, if n represents the price of oil in dollars, and x the allowable gas waste expressed in M cu. ft. Per day,

Jan 1, 1938

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher's3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.' In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968

By J. H. Hollomon, L. D. Jaffe, M. R. Norton

In the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermalt‡ decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work.§ Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. Method In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1947