Search Documents

By Bruce N. McIver, Leo Casagrande

Similarities are noted in the practices and problems of constructing dams to impound mine tailings, fly ash, and chemical wastes. The comparison of a typical tailings dam with a conventional water-retaining earth dam shows that the former is inherently less stable and can be susceptible to cracking, liquefaction, erosion, and frost action, as illustrated by examples. Several methods are presented for building safe tailings dams using either the coarse fraction of the tailings or local soils, the important factor in each method being proper compaction of the material. The safety of existing tailings dams can be improved by flattening the overall slope, preferably by adding berms, or by decreasing the height. Where neither remedy is possible, the installation of electro-osmotic tie-backs is suggested. Dumps of mine spoil can be stabilized economically by compacting the material in layers along the toe to form a dam.

Jan 1, 1971

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

Improved safety, economy, and flexibility-which translate into increased productivity-promote the case for greater utilization of diesel-powered equipment in underground coal mines. On the other hand, opponents of diesel use say that the alleged health hazards are not worth it. Who's right? The continuing debate was the focus of a special "Diesels in Underground Coal Mining" session held during the SME-AIME Fall Meeting in Lake Buena Vista, Fla., last September. Looking at the record to date, there are more than 20,000 diesel-powered units operating in underground mines throughout the world; more than 1000 are in Western European coal mines and 10,000 such units are in North American mines. Surprisingly, of the 10,000 North American units, only 200 are utilized in US underground coal mines.

Jan 4, 1979

By W. M. Peirce

ON May 16, 1871, twenty-two men met in Wilkes-Barre, Pennsylvania, and founded the American Institute of Mining Engineers.* If we could transport ourselves back to that year and survey the state of science and technology in general, and, in particular, the field of our immediate interest-nonferrous metals-we would feel a justifiable pride in what had been accomplished up to that time. These accomplishments in the metal field were at the moment in the process of documentation by an Englishman, J. A. Phillips, in a new 700-page edition of his book to be published in 1874 under the title of "Elements of Metallurgy." True, looking over his shoulder, we would smile to read that "all metals are capable of assuming a crystalline form under favorable conditions," and that tensile testing is done "by adding weights to a firmly suspended wire until it fractures," and we would find only three pages on aluminum and none on magnesium. We would, however, find an astonishing wealth of detailed knowledge on iron and steel and the then common nonferrous metals and alloys such as brass and bronze. But if we possessed a little prophetic vision as we directed our attention to the short period that had elapsed since the close of the Civil War, we

Jan 1, 1947

By Thomas H. Sheldon

In the zeal for opening up new ore-bodies, or for extracting the ore from attractive bodies already opened up, we very often lose sight of the fact, that, after all, the operation of a mine is a business proposition, pure and simple, and, for the best working-results, should be treated upon a strict business basis. Of course, in every mine of consequence, a record is kept of expenditures and receipts, and such glittering generalities as " gross receipts," " net receipts," " mining expenses," and a per cent. profit," can be told to the cent; but does this record show economy of management, as compared either with the same record of other months, or with the record of other mines of the same class ? Moreover, if such a record shows that the cost of mining is high, does it in any way enable the manager to put his finger on the leakage ? Does it necessarily follow that a mine which makes a profit of, say, 40 per cent. on 25-dollar ore, is doing less economical mining than one which saves 60 per cent. on 80-dollar ore ? Of course the figures in the latter case look the more attractive; yet when it comes to the point of saving everything which can be saved, and of cutting down expenses to the lowest possible cost of operation, the former mine is doubtless on the firmer and more economical financial basis. But as to the relative merits of the system of mining in the two cases, nothing could be decided without a basis of detailed comparison ; if one system is more economical than the other, why is it so, and wherein does the advantage lie ? This can be shown only by keeping accurately the cost of each mining operation. And no matter how dissimilar two mines may be in character and operation, yet there are a few general heads common to all mining operations. In the first place, it is necessary to break the ore from the solid ground;

Jan 1, 1907

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By H. A. Buehler

The Ozark region occupies a large part of the southern half of Missouri, the northern portion of Arkansas and comparatively smalll areas in northeast Oklahoma, southwest Kansas, and southern Illinois. It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The Boston Mountains extending for a distance of some 200 miles (321 km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Frangois Mountains in St. Frangois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.). The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. Stratigraphy The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Frangois Mountain district. Although located geographically near the eastern edge of the Osarks, the St. Frangois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Gene-vievg County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous action, since the first sedimentary beds were deposited.

Jan 1, 1918

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By D. L. McCain

Slurry transportation of coarse coal from the mining face to the preparation plant has proved successful in a West Virginia underground mine. Coal has been pumped from the mining section for several months. The system is currently being provided with the flexible link to the face to allow for continuous transportation. Some future plans for coal mines and projections for broader applications of the transportation method are given.

Jan 1, 1976

By A. H. Jones

(San Francisco Meeting, September, 1915). THE Belmont mill at Tonopah, Nev., was designed and constructed by the Belmont staff. Ground was broken in August, 1911, and milling operation started July 25, 1912. The metallurgical flow sheet, and the machinery adapted to carrying out operations in accordance with this plan, were decided upon from experience gained in the treatment of Belmont mine ores at the old Belmont mill at Millers, Nev. The detail drawings were made by the-engineering staff of the Tonopah-Belmont Development Co., under the supervision of Otto Wartenweiler, who also .had direct charge of the construction, consulting with the General Superintendent of the company, Frederick Bradshaw, and the writer.

Jan 8, 1915

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Walter Harvey Weed

introduction,.............715 "WHY ORE-DEPOSITS ARE Common about Igneous Contacts,. ..716 Outline of a Genetic Classification OF Ore-Deposits,.. .. 717 Ores of Igneous Origin.. .. .. .. .. 717 Igneous-Emanation Deposits........ 719 Fumarolic Deposits..........719 Gas-Aqueous Deposits.........719 Deposited by Meteoric Waters ........720 Contact Metamorphic Deposits.........720 Classes of Deposits......... 731 Contact Zones..........722 Character of Gangue..........722 Character of Ore-Deposit.........723 Literature...........724 Geographic Distribution.........724 Copper-Deposits—Cananea Type......725 British Columbia—Boundary District....725 Mexico..........727 Germany.......... 729 Gold.Deposits,...........731 Bannack Type.........732 Elkhorn..........733 Similkameen.........734 Changes in Rocks due to Contact Metamorphism....735 Changes in Mass. Volume. and Mineral Composition... 736 Genesis of Contact Metamorphic Deposits..738 Cause of Contact Metamorphism..738 Permanence in Depth............744 Mineral Veins near Igneous Contacts........745 Conclusions..............746 Introduction. This paper deals with certain ore-deposits whose structural features or mineral contents (or both) result. directly or indirectly. from igneous intrusions and their afier-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1903

By M. T. Halbouty

The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.

Jan 1, 1938

By Wilson Lundy

THE history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur Co. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico.

Jan 1, 1934