Search Documents

By G. R. Speich, R. A. Oriani

The rate of coarsening (Ostwald ripening) of copper precipitate Particles in an a-iron matrix has been studied in three Fe-Cu alloys containing 2.3, 4.0, and 5.4 wt pct Cu in the temperature range 730° to 830°C. The kinetics of Ostwald ripening ohevs the law as deduced by Lifshitz and Wagner so that matrix diffusion controls the process. The equilibrium shape of the particles is that of rods with hemispherical caps, and is due to the BOTH Lifshitz and slyozov and wagner3 have recently solved the complex problem of determining the rate of coarsening of an assembly of precipitate particles. Both workers, although using somewhat different mathematical approaches, arrive at the same equation for the relation between the mean radius 7 of a distribution of spherical particles and the bulk solubility co, diffusivity D in the matrix, large anisotropy in the copper/a iron interfacial free energy (y,/y, = 4). A Lifshitz -Wagner equation, modified for both the nonsphericity of the diffusion field and the reformulation of the Gibbs-Thomson equation for the case of nonsphencal particles, is derived. Using the modified equation, the calculated values of the mean radius are smaller than those observed by a factor of about one -half. absolute temperature T, gas constant R, surface free energy y of the precipitate/matrix interface, and the time t of aging: where V, is the molar volume of the precipitate and v is a stoichiometric factor. Wagner's treatment is restricted to the case of spherical particles growing in a liquid matrix where strain energy is not a factor. Lifshitz and slyozov have discussed the effect of anisotropic particle shapes and internal strains on the rate of coarsening. Oriani4

Jan 1, 1965

By AIME AIME

Council.* PRESIDENT O. THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1909.) VICE-PRESIDENTS OF THE COUNCIL. SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N. Y. PEPSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909.) J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, INCH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.)

Jan 5, 1908

By J. T. Eash, W. S. Crowell, E. M. Wise

The practice of dentistry, particularly the construction of artificial dentures and "bridges," involves a unique and difficult application of the precious-metal alloys. Appliances used in the mouth are continuously exposed to corrosive agencies which can hardly be described as mild, and must remain free from tarnish and be substantially immune to corrosion. Limitations with respect to space and weight demand high physical properties, while complexity of form requires ease of working. The high corrosion resistance required necessitates the use of alloys of high precious metal content. The usual expedient of resorting to mechanical working to produce the requisite strength and stiffness cannot be utilized because of the frequency of annealing and soldering operations. To meet these difficult conditions manufacturers of dental goods were early led, unknowingly perhaps, to the production of precipitation-hardening or temperable alloys. The excellent properties of iridium-platinum may have suggested the addition of platinum metals to the conventional gold-silver-copper alloys to produce greater strength and hardness. It was found that such quarternary alloys retained their high physical properties after passing through the usual soldering process; i. e., heating to 750° to 800" C. and cooling naturally in the air. Later it was discovered that they could be softened and rendered more ductile by heating to the same temperature and quenching in water. These early examples of precipitation hardening, for years the common knowledge of dental practitioners and laboratory technicians, escaped the attention of the scientific world and discovery of the transformation which was responsible for this hardening was disclosed by the Russian investigators of the system Au-Cu, Kurnakow, Schemtschushny and Zasedatelev~,(~)$ although the optimum conditions for securing good properties in aged alloys were not given attention.

Jan 1, 1932

By C. H. Mathewson, M. R. Pickus

The study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans, who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakaoj4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers16 were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1939

By M. R. Pickus, C. H. Mathewson

The study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centered cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans, who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakaoj4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers16 were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1939

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By Joseph F. Oesterele, Richard S. McCaffery

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By Richard S. McCaffery, Joseph F. Oesterele

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

Jan 1, 1901

By P. V. Roundy

PUBLIC lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934,' it contained 66,796 acres, of which only a small part had been defi-nitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not he done on any considerable scale under the Survey's usual appropriations; it gave employment to unem-ployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration.

Jan 1, 1937

By John T. Norton

In recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general interpretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystallization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hardness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By John T. Norton

In recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general interpretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystallization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hardness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By Robley D. Evans, Gerald L. Schroeder

Advanced techniques for control of radon (Rn) daughter product concenrrations (working levels, WL) in the uranium mines are discussed. Understanding the physical laws which govern the flux of radon into a mine, the growth and decay of the radon daughters, and the particulate nature of the daughters when suspended in air allows ventilation personnel to improve the quality of mine air with no increase in ventilation rate. The task of controlling, in a mine atmosphere, the short-lived nuclides produced in the decay chain of radon is a unique problem and as such should be approached with ventilation techniques specific to the problem. For most mines this has not been the case. Rather, procedures for removing these airborne radioactive nuclides have been borrowed directly from ventilation experience in mines where dilution ventilation was the traditionally accepted approach for air purification. With radon daughter products, this has often led to frustrating difficulties and expense. Primary origin of the airborne radioactivity is the a-ray-emitting noble gas, radon (222Rn, Rn), a nuclide formed by the decay of radium (226Ra, Ra). Radon, being a gas, may escape from its parent crystal and diffuse through the parent mineral into the interstices of the rock body. In a sandstone structure, about 20% of all the radon formed may find its way into the interstices of the rock. If a cavity such as a mine is nearby, the radon may diffuse through the rock interstices into the mine. While radium is usually highly concentrated in uranium ores, it is also found in varying concentrations in all minerals. Radon is therefore present in all minerals. In normal glacial till, the equilibrium interstitial radon concentration often equals 5000 pCi (picocurie, also uuCi) Rn per liter of pore volume.' In normal granitic rocks, the interstitial radon concentration often approaches 30,000 pCi per 1. Considering these typical, high-radon concentrations, radioactivity from airborne of daughter products is a potential problem unique not only to the uranium mining industry and should be considered as a potential hazard in all underground environments.

Jan 1, 1970

By W. S. Keyes

The State of Nevada, known par excellence as " the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the westcrn rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese Ever, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1879

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By E. F. La Vigne

ON Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Co. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about ½ mile south of the original shaft and plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-lined shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erected. This new plant began opera-tions on Dec. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours.

Jan 1, 1936

By Norman B. Pilling

The technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost' exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105' C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys. The reagent consists of a dilute solution of nitric acid and methyl alcohol in nitrobenzol. It is a great advantage to secure an anhydrous solution, as a tendency toward acidic etching has been traced to small amounts of water. A convenient method of preparation is to make an anhydrous stock solution of nitric acid in methyl alcohol in the proportion 20 per cent. acid by weight (12.5 per cent. by volume). The alcohol can

Jan 1, 1924

By John Johnston

WHEN I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in 1916-that is, about 25 years ago-in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father ¬Dr. Samuel Gridley Howe, his mother-Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature. is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-carbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable, tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass . . . by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes-and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. It tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works "f the watch was the best butter. If the reader learns no more than to beware of attempts to decipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942