Search Documents

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By H. V. Winchell

An examination of the Pachucal and El Oro districts in July, 1920, although cursory and incomplete, disclosed facts of more than passing interest to the student of ore deposits; and inasmuch as the literature on these districts is limited and some of their features are little understood, a brief account may prove valuable as reconnaissance observations to be amplified by more thorough and competent observers in the future. Where no complete monograph of important mining camps has been published a partial presentation of the data is often useful, as it sometimes leads to fuller and more accurate descriptions, by stimulating discussion. The following notes are presented with the consent of A. F. Main, managing director of the El Oro Mining and Railway Co., whose fund of information and wide acquaintance with both districts alone made it possible to cover so much ground in a short time. I have also to acknowledge gratefully the aid of C. A. Lantz and D. S. Calland of the Santa Gertrudis and Real del Monte companies, respectively, in connection with permission to inspect geological features of interest in their mines. Pachuca, Hidalgo, Mex. This mining camp has been described by Ezequiel Ordonez2 and by A. F. J. Bordeaux.3 Reported to have been discovered in 1522, it has produced silver valued at between $250,000,000 and $375,000,000. Subsequent to the discovery here, by B. de Medina, of the patio process. in 1557, its production was increased, and now, using cyanidation, the output of the camp is nearly one-sixth of the production of the world. Topography and Climate The Pachuca district consists of a series of mountains and valleys, the minor features of which extend in an easterly and westerly direction and reach elevations of 8000 to 10,000 ft. (2438 to 3048 m.) above the

Jan 1, 1922

By V. T. BERNER

THIS apparatus was designed primarily to meet the demand for a quick, efficient stopping to seal off the burning area temporarily during a mine fire, but it can be used in any circumstance where an immediate brattice is required for ventilation control. In using the old style brattice, mine-rescue workers have found it difficult, in smoke-laden drifts and stopes, to erect an effective stopping with wooden frame and canvas. Stulls must first be cut to the proper length, the canvas tacked in place, and the numerous irregularities of the walls and back must be caulked. This operation requires the employment of axes, saws, and hammers, which cannot easily and safely be handled in dense smoke. The fire fighters have often been forced to abandon their brattice, unfinished, because of the rapid approach of the fire, or because of the exhausted sup- ply of oxygen in their breathing apparatus. It is neces-

Jan 1, 1930

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz&apos;s theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty&apos;s work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz&apos;s theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty&apos;s work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

By William Mikulas

LITTLE work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn, and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallo-graphic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic com-pounds, and three of the structures were partly determined. No attempt was made to determine the range of homogeneity of the inter-metallic compounds.

Jan 1, 1937

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter&apos;s property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson&apos; observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter&apos;s property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By Charles M. Rolker

The Mariposa estate, a grant made by the Mexican Government to Juan 13. Alvarado, during the time when California was still under the dominion of Mexico, was purchased in 1847 by J. C. Fremont, and the United States patent issued to him in 1856. By sale, or its equivalent, money advanced, the property came into the hands of the Mariposa Company, June 25th, 1863, and through a varied existence of work and temporary inactivity, has as yet been kept as an undivided property, and rests at present with the Mariposa Land and Mining Company of California. I pass over this period of 15 years without giving the history of the ups and downs of the estate, partly because it is familiar to many, and also because I think in such a case this paper would assume too much the character of a narrative. The estate is situated in Mariposa County, California, about 170 miles southeast of San Francisco. It begins in lat. 37&apos; 26&apos; 38&apos;&apos; north, and long. 119&apos; 55&apos; west, and runs 6 miles north; thence 69 miles west; thence 5 miles northwesterly towards the Merced River; thence 84 miles southerly; thence 3 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 2 miles southerly; thence 2 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 1 mile northerly, and thence 2 miles easterly to the place of the beginning; embracing 44,387 acres (70 sq. miles) more or less. To describe this vast estate in detail as to its full geology, its numerous quartz veins, its many facilities to exploit them and work them by cheap methods, would lead me further than I intend to go at present, and I will content myself to describe the latest workings of the company and its immediate field of operations. As long ago as 1860 the late Dr. Adelberg advised the running of an adit from the northwestern edge of the estate at Benton Mills 011 the Mereed River. His object was to undercut the deepest workings of the then paying mines on the estate—the Pine Tree and Josephine. Following this advice, the tunnel known as "River Tunnel " was commenced. Its entrance is in S. 5, T. 4, s. R. 17 E. It is run in

Jan 1, 1879

Adams, Bernard, Student, South Dakota School of Mines. Rapid City, S. D. &apos;30 Ahlskog, Harold A., Student, Washington State College Pullman, Wash. &apos;30 Aldridge, John, Student, New Mexico School of Mines Socorro, N M. &apos;30 Almstrom, Adne A., Student, Met. Engrg., Washington State College Pullman, Wash. &apos;29 Ancell, Virgil F., Student, Missouri School of Mines Rolla, Mo. &apos;30 Ankudinoff, N., Mill Draftsman, Arthur G McKee & (:o., 2422 Euclid Ave., Cleveland, Ohio. &apos;30 Apablasa, Salvador C., Student, Univ. of California Los Angeles, Cal. &apos;31 Armstrong, Robert H., Student, Lafayette College Easton, Pa. &apos;31 Armstrong, Thomas E., Student, Univ. of California Los Angeles, Cal &apos;31 Aud, Robert A., Student, Lafayette College Easton, Pa. &apos;30 Backus, Robert Small, Student, Mass.- Inst. of Tech . Cambridge, Mass. &apos;30 Bailey, William C., Student, Univ. of California Los Angeles, Cal &apos;30 Banning, Lloyd H., Student, South Dakota State School of Mines Rapid City, S D. &apos;81 Barclay, M. G., Student, Colorado School of Mines Golden, Colo. &apos;30 Barger, Thomas, Student, Univ. of North Dakota Grand Forks, N. D. &apos;29 Barker, C. L., Student, Colorado School of Mines Golden, Colo. &apos;30 Barker, Edgar Morgan. Student, Univ. of Utah Salt Lake City, Utah. &apos;31 Barnwell, Earl E., Student, Oregon State College. Corvallis, Ore. &apos;30 Bartholomees, Geo. C Box 304, Bonne Terre, Mo. &apos;29 Bartholomees, Louis P., Student, Colorado School of Mines Golden, Colo. &apos;30 Bary, Robert L., Student, Univ. of Kansas Lawrence, Kans. &apos;30 Basham, Lester G., Student, South Dakota School of Mines Rapid City, S D. &apos;31 Bates, Walter H., Student, School of Mines, Univ. of Utah .. Salt Lake City, Utah. &apos;30 Beardshear, George T., Student, South Dakota State School of Mines.Rapid City, S D. &apos;31

Jan 1, 1923

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

By Cyril Stanley Smith

BeTa brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, hut at low temperature< an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shock1ey.l All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching&apos; With most ordered alloys, cold-working induces disorder and

Jan 1, 1943

Present indications are that the Fourth National Exposition of Chemical Industries, to be held in Grand Central Palace, New York, Sept. 23 to 28, will be the greatest exhibition of its kind ever held. Preparations are well under way and the advisory committee is working hard to make, every department of the affair a success. Men prominent in the chemical and allied industries will speak on subjects vital to present conditions and needs. Dr. C. H. Herty, and Dr. G. W. Thompson, President of the American Institute of Chemical Engineers, are to make opening addresses. F. J. Tone, President of the American Electrochemical Society; Dr. W. H. Nichols, President of the American Chemical Society, and several others, are expected to make addresses also. Prof. Joseph W. Richards will speak on : ?Ferro-alloys of silicon, tungsten, uranium, vanadium, molybdenum, and titanium." Theodore Swann, President of the Southern Manganese Corporation will speak on "Ferro-manganese." The program for the exposition is in active preparation. There will be a series of symposiums on the "Development of Chemical Industries in the United States, notably since July, 1914." Among other topics for consideration is that of potash development; C. A. Higgins, of the Hercules Powder Company, will speak of the operations of that company in the recovery of potash from kelp; Linn Bradley, of the Research Corporation, on its recovery from cement dust, and other sources, by electrical precipitation. Other symposiums will be devoted to chemical engineering, acids, industrial organic chemistry, the ceramic industries, and the metal industries. Among the speakers are: A. Hough.-" Chemical Engineering in Explosives: TNT; TNA; Picric Acid; and Nitrobenzol." E. J. Pranke.-" Development of Nitric Acid Manufacture." S. P. Sadtler.-"Development of Industrial Organic Chemistry." Geo. H. Tomlinson.-" Wood as a Source of Ethyl Alcohol." C. A. Higgins.-"Kelp as a, Source of Organic Solvents." Alcan Hirsch.-" Pyrophoric Alloys."

Jan 9, 1918

By L. S. Panyity

The inception of this paper may be traced directly to the various discussions of another paper by the writer1 wherein certain indefinite beliefs and opinions were emphasized as to the relative importance of total sand porosity and the actual size of the openings between the grains. Since publication of that paper it has been possible to study various methods of sand analyses and results that have been obtained under different conditions and actual operations in the field. The purpose of this paper is to indicate the value of screen analysis, especially in areas where repressuring by means of water-flood, air or gas is being used in the partly depleted fields. Sand samples have been analyzed for porosity, saturation and grain size. They are mainly from the Bradford water-flood area, where a great reliance has been put upon such analyses, and where many data are available, A few sand studies are included from fields other than the water-flood area, in order to indicate the possibilities of screen analysis in any field. Examples of various conditions are given in Figs. 1 to 7, which show the porosity, saturation and grain-size analyses of submitted cores or drill cuttings. The generally accepted methods of delineating such sand studies on cross-section paper, known as "core charts" has been employed; with the exception that a method of representing grain size has been evolved which is believed to be the best adapted for this purpose. It differs from the block diagrams generally used, in the employment of a linear section. Percentage of grain-size is represented by the subdivision of a given distance, where the total length represents the whole sample of rock chunk, while the subdivisions indicate the percentages of grains of the different sizes that will pass through the various sieves, through which the samples of crushed sand are sorted to determine the size and amount of the components that make up the aggregate. Thus, on Fig. 1, under the heading of Grain Size, the first samples are composed of grains of the following sizes: 16 per cent. through 120-mesh sieve; 33 per cent. through 150-mesh; 25 per cent. through 180-mesh; 26 per cent, through 200 mesh; a total of 100 per cent. A minus sign is placed before

Jan 1, 1931

By Cyril Stanley Smith

BETA brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, but at low temperatures [ ] an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An [ ] excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shockley.1 All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching. With most ordered alloys, cold-working induces disorder and

Jan 1, 1942

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.&apos;&apos; Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.&apos;&apos; Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.&apos; The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963