Search Documents

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960

By R. W. Raymond

(Reprinted With some additions and changes from the Engineering and Mining Journal)] THE death of Prof. Samuel Benedict Christy on the 30th of November,. at the age of 61 years, cuts short a brilliant and influential professional career. He was born in San Francisco, Aug. 8, 1853, and was graduated as Bachelor of Philosophy at the University of California in 1874. For the five years that followed, he studied mining and metallurgy as a post-graduate in the same institution, serving also as instructor in analytical chemistry, and becoming in 1879 instructor in mining and metallurgy¬a position which he held until 1885. During this period he became known also by his contributions to technical literature, the earliest of which, perhaps, was his report on the Monte Diablo coals (in 1875); but the first which drew my attention to him was an exceedingly able discussion (in 1879) of the genesis of the quicksilver deposits of California, in which he followed with much acuteness and originality the lead of Professor Becker, who had been teaching at the University of California. The notion of the thermo-aqueous formation of such deposits was then new; and the laborers in a field now familiar to every student deserve the credit due to pioneers. For some years the subject of quicksilver seems to have occupied much of Christy's attention. In 1877, he described the mines and works at Almaden, Spain; in 1884, the Imperial quicksilver works at Idria, Austria; in 1889, the New Almaden mines of California. But his great work was the creation of the school, of mining and metallurgy at the University of California, which may be said to have begun with his occupancy of a full professorship of these branches. It is not necessary here to recount the early difficulties and perils of the University, and its long struggle for academic independence of political control or interference. The battle is over, and the institution is now upheld by the intelligent loyalty of the citizens of California, without regard to party. But while the issue was uncertain, the development of special schools of applied science was scarcely practicable. Doctor Becker and William Ashburner had given up the school of mines as a hopeless task when Christy, younger and less experienced, took it up. As he wrote me in February, 1901-

Jan 4, 1915

By J. A. Singmaster

A REPORT that it did not pay to use present-day galvanized iron on account of the short life of the material, accompanied by proofs of the state-ment in the form of a tabulated history of the first costs of various kinds of building materials and their main-tenance expense, started an investigation of modern galvanized products. At the very outset it was apparent that our experience with galvanized products was by no means unique. Correspondence with the State Agricultural Depart-ments, the Agricultural Experiment Stations, the County Agents and State Granges all over the United States brought a mass of complaint on this same score. Visits to large buyers of galvanized sheet and wire revealed the same condition coupled with an ever-increasing use of substitutes for galvanized iron. We believe, therefore, that the title of this article is fully warranted by the experience of the consuming public. A study of the proceedings of the various societies having to do with the testing and use of sheet iron and steel products revealed a tremendous amount of work on the life of the base metal itself. Great stress was laid on differences in life of various types of iron and steel, the difference amounting at best to months rather than years. Very little recent attention has been paid to a study of the life of the zinc coating and the causes of its present-day lack of durability. There have been some real exposure studies published, how-ever, which show that the weight of the zinc coating determines the protection afforded by the galvanizing, which is of far greater influence on the life than the base-metal composition. An interesting paper was published by the Phillipine Journal of Science in 1916, entitled: "Galvanized Roofing in the Phillipines," a contribution from the Bureau of Science of the Phillipine Island Government. The author, Mr. Arguelles, found on 18 old galvanized sheets, after from 30 to 35 years' exposure, from 2.3 to 4.1 oz. of zinc per sq. ft. of sheet and sums up the study by saying: Of the various factors influencing the durability of galvanized iron which have been studied with a view towards accounting for the difference in behavior of old and modern sheet, it appears evident that the greater weight of zinc per unit of area on the former accounts for the greater durability.

Jan 10, 1922

By Joseph Jensen

FROM Aug. 31, 1937, until Apr. 30, 1939, there were 40,872,610 bbl. of oil run to storage in California; from Apr. 30, 1939, to Aug. 31 of the same year 5,512,912 bbl. were withdrawn from storage. But from Aug. 31, 1937, to Aug. 31, 1939, the number of producing wells in the state has increased from 17,706, with a potential production of 1,323,202 bbl., to 18,910, with a potential of 2,302,282 bbl. Thus, in a period of two years, during the first 20 months stocks increased over 1/3 and during the following four months stocks decreased 1/30. In the same two years the number of productive wells increased 1/15 and potential increased 3/4. Undoubtedly, the large increase in stocks created the pressure that caused the reduction in stocks that followed; yet this has come about in spite of the larger number of wells and higher potential. Cause of the change was the adoption on May 17, 1939, by the Central Committee of California Oil Producers of a uniform method of oil curtail-ment for all wells throughout the state. Acceptance of the method in the four months following adoption by practically all fields in California indicates that producers generally are convinced of its merit and fairness. True, some operators still overproduce, but the restraint practiced by the remainder of the industry has been sufficient to turn a situation headed for chaos into one of reasonable stability. Credit for this change goes to the industry itself, because it has all been accomplished under voluntary oil curtailment.

Jan 1, 1940

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphate from the soil. Man's most important use of phosphate is for fertilizer; however, he is also a heavy user of many industrial phosphate chemicals. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and saltwater. The average content in rocks is 0.1 to 0.2% P2O5, as documented recently by McKelvey (1973). About 200 minerals contain more than 1 % P,O,. However, the important one in igneous rocks is fluorapatite, (Ca,(PO,) ,F) containing about 42% P,O, and 3.8% F,; in sedimentary rocks the one important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO,. Both are in the apatite family of minerals. The mineralogy of phosphate minerals was reviewed recently by Altschuler (1973). Although phosphate occurs in nearly all rocks, economic recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade and must be concentrated.

Jan 1, 1975

By R. F. Marande, R. S. Busk

THE magnesium-aluminum-zinc system contains most of the magnesium-base alloys used commercially, although in practice the ternary, alloys are usually modified by the addition of a small amount [ ] of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the object of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.1 [ ] All alloys reported were made in 15-lb. melts, superheated to 1700°F. for 15 min., cooled to 1400°F. and poured in sand molds. The test bars produced had a ½ in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. CONSTITUTIONAL DATA Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By C. L. Berrier, Wm. B. Daly

Jan 1, 1923

By Wm. B. Daly, C. L. Berrier

Jan 1, 1923

By F. Milton Lewis, Roshan B. Bhappu

The methods for preparing operating cost estimates for a proposed mining venture are outlined. The procedures for estimating the direct and indirect operating cost for proposed mining and ore processing facilities are reviewed. Profits from the by-products are credits to the total operating cost, direct plus indirect, and are subtracted to obtain the total net operating cost. The non-operating costs which are a part of the total expenses are defined but are not considered in this manuscript. A method for developing the operating cost for a typical copper concentrator in the southwest is described in detail.

Jan 1, 1978

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By Walter Miller

A surprising development during the year was the continued high demand for petroleum products and the high level of crude oil charges to the stills. Generally speaking, the petroleum industry during 1946 succeeded in producing a greater quantity of crude oil and petroleum products than in any of the war years, and considerably exceeded the production of any prewar year. Daily crude still charges averaged between 4,700,000 and 4,800,000 bbl per day for 1946 and about equaled the 1945 record, although most pessimistic 1945 guesses, predictions, or fears ranged, for 1946, from only 3,900,000 to 4,400,000 bbl per day. In spite of the high crude charge to the stills, total stock of crude oil was higher at the end of the year by some 7,000,000 to 8,000,000 bbl. A similar story holds regarding stocks of the principal refined products. Gasoline on hand at year's end was two to three million barrels lower, and was considered low for the expected demand during the coming high consuming season, while stocks of light and heavy fuel oils, although some higher than a year previous, hardly reached a comfortable level. The trend in gasoline of high octane number, which has resulted in a marked rise in. the antiknock quality by the end of 1945 (five or six numbers higher than during the war and one number higher than the prewar quality of civilian motor gasoline of 1941) was abruptly arrested by an acute shortage of metallic lead for manufacturing tetraethyl lead. Government action in the form of lead price control, rationing, and the setting of octane ceiling specifications to conform to the reduced ethyl lead compound available were enforced until abrogated at the end of the year. It will be interesting to see how rapidly the octane levels will resume the rising trend, as more metallic lead slowly becomes available for making greater quantities of ethyl lead compound. As octane quality rises over present levels the disadvantage of the refiner without catalytic cracking equipment will increase. Gasoline made by catalytic cracking, without addition of ethyl lead, approximates 77 octane by the official ASTM Motor Method test, compared with 66 for gasoline generally similar in volatility made by the older thermal cracking operation. Catalytic gasoline shows an even greater improvement in the Research octane number, the comparison being roughly 86 Research versus 71 Research octane for the thermal cracked product. This higher differential in Research octane is credited by many, although not universally so, as contributing to better road performance, and consequently resulting in a more desirable product marketwise. In some parts of the country a premium of roughly one fourth cent per gallon is now being paid for gasoline with higher Research octane made possible by including catalytic cracked product in the final blends. If such price differentials in favor of catalytic gaso-

Jan 1, 1947

By Walter Miller

A surprising development during the year was the continued high demand for petroleum products and the high level of crude oil charges to the stills. Generally speaking, the petroleum industry during 1946 succeeded in producing a greater quantity of crude oil and petroleum products than in any of the war years, and considerably exceeded the production of any prewar year. Daily crude still charges averaged between 4,700,000 and 4,800,000 bbl per day for 1946 and about equaled the 1945 record, although most pessimistic 1945 guesses, predictions, or fears ranged, for 1946, from only 3,900,000 to 4,400,000 bbl per day. In spite of the high crude charge to the stills, total stock of crude oil was higher at the end of the year by some 7,000,000 to 8,000,000 bbl. A similar story holds regarding stocks of the principal refined products. Gasoline on hand at year's end was two to three million barrels lower, and was considered low for the expected demand during the coming high consuming season, while stocks of light and heavy fuel oils, although some higher than a year previous, hardly reached a comfortable level. The trend in gasoline of high octane number, which has resulted in a marked rise in. the antiknock quality by the end of 1945 (five or six numbers higher than during the war and one number higher than the prewar quality of civilian motor gasoline of 1941) was abruptly arrested by an acute shortage of metallic lead for manufacturing tetraethyl lead. Government action in the form of lead price control, rationing, and the setting of octane ceiling specifications to conform to the reduced ethyl lead compound available were enforced until abrogated at the end of the year. It will be interesting to see how rapidly the octane levels will resume the rising trend, as more metallic lead slowly becomes available for making greater quantities of ethyl lead compound. As octane quality rises over present levels the disadvantage of the refiner without catalytic cracking equipment will increase. Gasoline made by catalytic cracking, without addition of ethyl lead, approximates 77 octane by the official ASTM Motor Method test, compared with 66 for gasoline generally similar in volatility made by the older thermal cracking operation. Catalytic gasoline shows an even greater improvement in the Research octane number, the comparison being roughly 86 Research versus 71 Research octane for the thermal cracked product. This higher differential in Research octane is credited by many, although not universally so, as contributing to better road performance, and consequently resulting in a more desirable product marketwise. In some parts of the country a premium of roughly one fourth cent per gallon is now being paid for gasoline with higher Research octane made possible by including catalytic cracked product in the final blends. If such price differentials in favor of catalytic gaso-

Jan 1, 1947

By Courtenay de Kalb

THE Exposed Treasure gold-mine has, for the past four years, been one of the largest producing mines of Southern California, its annual output having constituted 1 per cent of the total gold and silver production of the entire State. At the present moment the property is idle, owing to the large quantity of water encountered oil the lower levels, which will require the installation of a powerful pumping-plant before operations can be recommenced. Moreover, a prompt change in the character of the ore has occurred at water-level, which makes imperative an extensive campaign of development in the region of the unoxidized ores before a plant adapted to their treatment can be definitely decided upon. The character of the changes encountered in these deeper ores makes the geology of this deposit a matter of importance, not only for the immediate district, but for the desert region of Southern California in general, where many mines exist having in the oxidized belt conditions that, in many respects, resemble those in the Exposed Treasure mine. The deposit is situated in an apparently isolated butte about 2.5 miles south from the town of Mojave, on the Mojave desert; The butte, though apparently isolated, is in fact geologically part of an extinct volcano, known as Soledad butte, which rises out of the plain 1,5 miles SW. of the mine, to an altitude of 4,650 ft. above sea-level. Other buttes also rise from the desert plain toward the south and east, and again to the westward, all being closely related geologically to Soledad butte,-the whole constituting a single system as to origin and time. Since the end of the period of active volcanism in this region, there has been extensive denudation, the ancient plateau having been dissected during an epoch of apparently exces-

Jan 1, 1907

By William Hamilton Merritt

A brief paper on this subject (which might readily be made to, fill a volume) is suggested at this time by several considerations, among which may he named the meeting of the Institute on the borders of Ontario, not far from some of the mining undertakings which are hereafter mentioned ; the mineral developments made in the Province quite recently ; the highly creditable collection of most of the minerals of Ontario, for the first time got together, and exhibited this year at Cincinnati, in the Centennial Exhibition of the Ohio Valley ; and, finally, the recent appointment, by the Government of Ontario, of a Commiesion to inquire into, and report upon the mineral resources of the Province, and the best means to be adopted for their development. The Province of Ontario has no Department of Mines or official geologist, to take note, and keep record, of mining and mineralogical development and discovery. Within the last few years some valuable statistics have been collected by Mr. A. Blue, the Deputy Minister of Agriculture; but recently a desire has risen on the part of the people to obtain further knowledge of these subjects, and the government has appointed a Commission, the report of which is expected to be issued in part, if not in completed form, this winter.

Jan 1, 1889

By J. W. JESSUH

TO certain people the name of Northern Rhodesia brings only a vague recollection of a distant country somewhere in Africa; to others, it means a big game territory and the opportunity for excellent shooting; to some, a land of sunshine and peace; but to mining men the name signifies the land where the latest discoveries of copper ore are astonishing the mining world and bid fair, in a few years, to make Northern Rhodesia one of the largest copper- producing countries. There is a fascination about this part of the globe that is somewhat similar to southern California, and at the same time there is that feeling of mystery peculiar to a tropical climate. Perhaps it is the isolation, the fear of wild animals, or the influence of an undefinable something which cannot be expressed.

Jan 1, 1931

By R. A. Pallanch

Probably one of the most perplexing problems with which a mill operator contends is the proper evaluation of his mill results. True, he accurately determines his recoveries of metals and grades of products monthly, weekly, and often daily. These figures do not of themselves directly translate to mill economics. When one figure is unusually good there may be an offsetting circumstance. The advantage of high lead or zinc concentrate grade may be offset by poorer recovery; high lead recovery may be offset by poorer zinc recovery, or vice versa; and so on. Besides, grades or recoveries may not of themselves mean more than a reflection of the grade and character of the ore during the period under study. What the operator sorely needs is some one measuring stick that tells him when he has achieved his greatest return, regardless of grades or recoveries—for if he knows his methods and practices are yielding the optimum return he need no longer concern himself with the assays of products and tailings, or the corresponding distribution of metal values. At first blush it would appear that the obvious answer to this is the actual money return to the mill. Paradoxical as it may seem, however, money return does not make a dependable yardstick any more than do grades and recoveries, as ore condi- tions would vary enough to bring about greater money return during periods when the actual metallurgical work is not as good. The mill operator, of course, should always aim for the greatest return on the ore, once it is in the mill bins, with proper attention always to mill treatment cost. The need of a proper yardstick becomes more imperative with the increasing complexity of the problem. In the case of a simple, single-product operation on a fairly uniform ore, in which only one metal is of significant importance, the need is not great, as grade and recovery pretty well tell their own story. At the other extreme is the operation that makes three or four separate marketable products from a complex mixture of heterogeneous ores that vary tremendously in individual metal contents and ratios, degree of oxidation, and other characteristics, and in which gold, silver, copper, lead and zinc are all significant values. Economic Recovery The first attempt at obtaining a proper single yardstick for a fairly complex ore with which I am familiar is the use of the ''Economic Recovery" term at the lead-zinc flotation mill of the Sunnyside Mining and Milling Co., Eureka, Colorado. This method had been applied there early in Sunnyside flotation-mill history (not later than 1920) and credit for the innovation I believe belongs to Messrs. Kuryla and Marquand. The term "Economic Re-

Jan 1, 1949