Search Documents

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

In the Philippines, where distances are spoken of in terms off fight time, the Sipalay copper mines are two flight hours southeast of Manila on the island of Negros. After landing at the airport in Bacolod, it is then 170 km (106 milers) by surface transportation to Marinduque Mining and Industrial Corp.'s expanding copper operation. While copper deposits were discovered in the area in 1936-and one mine, the Binulig, began operations soon after-it wasn't until 1956 that stripping at Sipalay and construction of a 4000-t/d (4400-stpd) mill began. The mill went into operation in May 1957, and the first shipment of copper concentrate was made three months later.

Jan 8, 1978

By W. E. Wrather

SERIOUS consideration was given by the Petroleum Division to a wide variety of subjects, during six busy sessions at the Annual Meeting. Beginning with a joint session on engineering research and production engineering, Tuesday afternoon, conducted by E. A. Stephenson and H. C. Fowler, problems of petroleum technology, domestic and foreign production, proved oil re- serves, economics, and stabilization were mooied almost without interruption until nearly everyone was "talked out,' and the meeting was adjourned at the end of the annual Petroleum Division dinner, late Thursday night.

Jan 1, 1933

The Library of the above-named Societies is open from 9 A.M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The tine spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1917

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By HOWARND N. EAVENSON

THE year 1930 resembled the preceding one in the coal industry in continuing the era of falling prices and 'of the abandonment of unprofitable mines. Practically all coal prices fell, and in the steam sizes during the last half of the year this was particularly true, due to the small industrial demand. No new mines of any size were opened in the bituminous coal industry, but there was a steady increase in the number of cleaning plants of all kinds built in all fields. It is estimated that at least nine million tons per year were added to the previous total of washed coal. The largest washing plant started during the year was that of the Buckeye Coal Co., at Nemacolin, Pa., with a capacity of 650 tons per hour. Fig. 1 shows - the mixing-bin, conveyor galleries, washing-plant and skip hoist, and Fig. 2 the 120-ft. Dorr thickener for collecting the 48-mesh material from the wash water. Dryers are used for drying the steam coal product. The following statement by J. R. Campbell shows the effect of cleaning on Pittsburgh coal in Greene County: "With the advent of the 650-t.p.h. efficient washing plant in Greene County at the Nemacolin mine of the Buckeye Coal Co., it has undoubtedly been demonstrated that the potential coking-metallurgical coals of the county can be brought within the pale of the highest grade high-volatile coals for steel manufacture. A few months' operation indicates that 9% per cent ash in the raw coal can be easily reduced to under 7 per cent ash in the washed coal and the sulfur from 1.60 per cent in the run of mine to 1.20 per cent sulfur in the washed coal.

Jan 1, 1931

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By P. V. Brough, K. B. Gillaspie

DECISION to build a mill at the Bayard property was made in May 1942. Western-Knapp Engineering Co., of San Francisco, assisted by engineers of U. S. Smelting, handled the design and construction. Much of the milling equipment was moved from the Company's mill at Goldroad, Ariz. Wartime restrictions necessitated wood construction and paper sheathing except for structures adjacent to the Bullfrog shaft. Construction started in September 1942 and milling in March 1943. Bayard ores are processed in a single-ection mill. About half of the ore treated during the past year was hoisted through the Bullfrog shaft and the rest was trucked from other shafts. Coarse storage includes four bins, two of 120 tons each for Bullfrog ores and two of 85 to 120 tons each, served by a truck ramp. The low capacity figure refers to

Jan 1, 1948

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

Jan 1, 1942

By W. M. Albrecht, W. D. Klopp, R. I. Jaffee, B. G. Koehl

Kinetic studies were made of the reactions of tantalum with oxygen, nitrogen, and air at 400o to 1500°C. The tantalum-oxygen reaction is linear from 500° to 1250°C. The tantalum-nitrogen reaction follows a cubic rate law at 400° to 700°C and a parabolic rate law at 800" to 1475°C. The reaction behavior in air is initially parabolic followed by a transition to linear behavior. In the search for high-temperature materials, considerable interest is being shown in the refractory metal, tantalum. It is the third highest melting metal with a melting point of 2996°C. Also, tantalum has excellent ductility, making it one of the most workable refractory metals. In considering high-temperature applications of tantalum, the oxidation kinetics of the metal must be known. Such information also serves as a basis for the development of corrosion resistant tantalum-base alloys. Therefore, this study was made to investigate the reaction of tantalum with air, nitrogen, and oxygen. LITERATURE Several oxides of tantalum have been reported. The pentoxide, Taz05, is the only oxide of tantalum whose identity has been established. A high-temperature modification, aTa2Os, has been reported by several investigators.1-4 A low-temperature phase, ßTa2O5, undergoes an allotropic transformation at 1320o to 1350oC. 5-8 Four other oxides of tantalum have been reported. The oxides TaO2, TaO, and Ta4O have been reported by schonberg.9 A suboxide Ta2O, was observed by Wasilewski 6. However, the presence of oxides lower than Ta2O5 is questioned by Lagergren and Magneli.7 In oxidation studies, vermilyeal0 and Peterson, et al.,12 reported one possible phase intermediate between Ta and Ta2O5. Only Ta2O5 was formed in the tantalum air reaction, as reported by Michae1.l3 Several studies have been made on the kinetics of the tantalum-oxygen reaction. vermilyeal4 investigated the range 50° to 300°C and found that the rate of growth of a thin adherent oxide film could be described by the Cabrera-Mott theory. Gulbransen and Andrew15,18 studied the reaction kinetics of tantalum in oxygen pressure of 1/10 atm at 250° to 450°C. At all temperatures the reaction followed the parabolic rate law for periods up to two hours. The oxidation behavior in the range 500" to 1000°C was found to be linear at oxygen pressures of 0.2 to 600 psi according to Peterson. et al.l1 At very low pressures (1 x 10-3 to 2 X lo-&apos; mm of Hg) Gebhardt and seghezzi17 reported linear oxidation at 800° to 1500°C. The reaction of tantalum with air is similar to the reaction with oxygen. Studies have been made by Waber, et a1.,12 and Michae1.l3 Two nitrides of tantalum, TaN and Ta2N are known. Their structures have been determined by Brauer and Zapp 18,19 The tantalum-nitrogen reaction kinetics have been investigated by Gulbransen and Andrews. 15, 16 The reaction follows the parabolic rate law at 500° to 850°C at a nitrogen pressure of 1/10 ,atm. At the same temperature, the tantalum-nitrogen reaction is much slower than the tantalum-oxygen reaction. EXPERIMENTAL TECHNIQUES Material— The material used in this study was high-purity, electron-beam-melted tantalum obtained from the Temescal Metallurgical Corp. The hardness of the as received ingot was 76 Vhn. The analysis of the material is given in Table I. Methods—Cylindrical specimens of tantalum approximately 0.9 cm in diam and 0.5 cm in length

Jan 1, 1962

By George Branner

THERE is no record of the commercial production of bentonite as such in Arkansas up to the present although fuller&apos;s earth has been. mined intermittently in the state1 from 1891 to 1922. Very nearly all of this was obtained from decomposed basaltic dikes.2 Recently three bentonite deposits of close stratigraphical relationship have been identified in the Coastal Plain region of southern Arkansas, which suggests that there may be a considerable quantity of commercial material available. LOCATION AND ACCESSIBILITY The three deposits are located respectively in the SE. ;1/4 SE. ;1/4 sec. 13, T.- 2 S., R. 13 W., Saline County, the SE. ;1/4 SE. 1/4 sec. 18, T. 5 S., R. 16 W., Hot Spring County, and in sec. 22, T. 12 S., R. 19 W., Ouachita County. The Saline County deposit is 14 miles by state highway 167 south of the city limits of Little Rock and 1 mile west by dirt road. This deposit is 12 miles south of Ward switch on the C. R. I. P. Railroad and 11 miles east of Vimy Ridge by dirt road. Vimy Ridge is also on the C. R. I. P. Railroad. The Hot Spring County deposit located in the SE. ¼ SE. ;1/4 sec. 18, T. 5 S., R. 16 W. is about 100 yd. north of Durian switch on the C. R. I. P. Railroad and on state highway No. 9, 5 miles southeast of Malvern. The Ouachita County deposit has not been accurately located but lies in sec. 22, T. 12 S., R. 19 W. It is approximately 2 miles by road from Chidester on the Missouri Pacific Railroad.

Jan 1, 1929

By I. C. White, G. H. Ashley, J. A. Bownocker

Among the rich mineral deposits of the great Appalachian field, the Pittsburgh coal bed stands pre-eminent. Other coal beds may cover a wider area, or extend with greater persistence, but none surpasses the Pittsburgh seam in economic importance and value. It was well named by Rogers, and his able assistants of the First Geological Survey of Pennsylvania, in honor of the city to whose industrial growth and supremacy it has contributed so much. Whether or not the prophetic eye of that able geologist ever comprehended fully the part which this coal bed was to play in the future history of the city that gave it a name we do not know; but certain it is that the 7 ft. of fossil fuel, which, in Rogers&apos; time, circled in a long black band around the hills and, overlooking the site of Pittsburgh from an elevation of 400 ft. above the water of the Allegheny and Monongahela, extended up the latter stream in an unbroken sheet for a distance of 200 miles, has been the most potent factor in that wonderful modern growth that has made the Pittsburgh district the manufacturing center of America, and that bids fair to continue until it shall surpass every other district in the world, even if it does not now hold such primacy.&apos; The Pittsburgh coal bed stands today as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? It has contributed to Pennsylvania alone more than 2,500,000,000 tons of high-grade coal worth nearly $4,000,000,000; since 1910, it has added more than $2,500,000,000 to the value of Pennsylvania&apos;s mineral output. In 1920, this bed2 contributed 127,227,000 tons of coal as follows: Pennsylvania, Pittsburgh district........................ 38,245,000 Connellsville district................................. 34,095,000 Weatmoreland-Ligonier district........................ 16,107,000 88,447,000 West Virginia, Fairmont district........................ 15,571,000 West Virginia-Ohio, Panhandle No. 8 district............. 21,128,000 Maryland-Potomac (Est. one-third of production)......... 2,081,000 38,780,000 Total........................................... 127,227,000

Jan 1, 1927

By Charles Behre

THIS paper deals with recent geologic studies in the slate belt of Northampton, Lehigh and Berks counties, Pennsylvania. The work was conducted under the auspices of the Pennsylvania Topographic and Geologic Survey. Three years have now been spent in detailed consideration of the economic geology of this region. In the field, particular attention was paid to the bearing of geology on quarry development and property valuation and the object of this paper is to summarize the results from that viewpoint. Excellent studies of a somewhat similar nature have already been carried out by Bowles,1 but with the emphasis upon the details of quarrying and fabricating methods, rather than upon the geologic relations. THE NORTHAMPTON-LEHIGH-BERKS DISTRICT Location The region here discussed lies in east-central Pennsylvania and extends southwestward from Delaware River, on the New Jersey line, to the Schuylkill in north-central Berks County. It is an elongated belt occupying the northern sections of the three counties mentioned and lying along the southern edge of Blue Mountain. Its length is about 50 miles and its average width five or six, though in places it attains a maximum of 10 miles.

Jan 1, 1928

By Henry Louis

IN the discussion on the paper on subsidence by R. V. Norris and H. W. Montz (Teohnical Publication No. 153), H. N. Eavenson has been good enough to quote some of my views regarding the phenomena of subsidence; he has, of course, only mentioned these briefly, and as he has not represented them quite correctly, it is evident that I have failed to make them clear. Seeing that he, and apparently some of the others who took part in the discussion, appear to hold views different from my own, I think it advisable to put my opinions down as definitely and as clearly as possible, because it appears to me at least possible that some of the differences above referred to may be differences of language and definition rather than of fact. The statements I propose to submit refer to the simplest cases, namely where an area in a practically horizontal bed has been entirely worked out. My experience has been confined to beds of bituminous coal and of ironstone, but D I do not at the moment see why there should be any difference in principle between the working of a bed of anthracite and one of bituminous coal, provided that the other conditions are the same. I wish to emphasize that I am considering the conditions of complete working out of the mineral bed with the roof allowed to come down and form goaf in accordance with the general British practice; 1 am excluding, therefore, methods of hydraulic, pneumatic, and hand stowage where extraneous material is brought in to hold up the roof. I am also excluding the case of bord and pillar working where pillars of small size are deliberately left in, apparently with the idea that these will subsequently crush and let the roof down gradually. Such a method of mining has long been discontinued in this country, indeed in Europe generally, and I venture to predict that the time will come when such a recklessly wasteful method will no longer be tolerated even in the United States. Further, I am referring entirely td static conditions after the mineral bed has been worked out and the ground has come to rest; the phenomena that occur during the course of extraction are much more complicated, and these I am not discussing here. Under these conditions, I have

Jan 1, 1929

By H. O. McLeod, J. M. Campbell

This paper presents the results of the data obtained in the first stage of a long-range study at high pressures of the system, vapor-hydrate-water rich liquid-hydrocarbon rich liquid. The data presented are for the three-phase systems in which no hydrocarbon liquid exists. Tests were performed on 10 gases at pressures from 1,000 to 10,000 psia. One of these was substantially pure methane, and the remainder were binary mixtures of methane with ethane, propane, iso-butane and normal butane. Several conclusions may be drawn from the data. 1. Contrary to previous extrapolations, the hydrocarbon mixtures tested form straight lines in the range of 6,000 to 10,000 psia which are parallel to the curves for pure methane, when the log of pressure is plotted vs hydrate formation temperature. 2. The hydrate formation temperature may be predicted accurately at pressures from 6,000 to 10,000 psia by using a modified form of the Clapeyron equation. The total hydrate curve may be predicted by using the vapor-solid equilibrium constants of Carson and Katz&apos; to 4,000 psia and joining the two segments with a smooth continuous curve between 4,000 and 6,000 psia. 3. The use of gas specific gravity as a parameter in hydrate correlations is unsatisfactory at elevated pressures. 4. The hydrate crystal lattice is pressure sensitive at elevated pressures. INTRODUCTION Prior to 1950 many studies had been made of the hydrate forming conditions for typical natural gases to pressures of 4,000 psia.""&apos;"&apos;"" Most of these attempted to correlate the log of system pressure vs hydrate formation temperature, with gas specific gravity as a parameter. One of the more promising correlations was made by Katz, et al, which utilized vapor-solid equilibrium constants. The only published data above 4,000 psia are those of Kobayashi and Katz7 for pure methane to a pressure of 11,240 psia. In the intervening years, most published charts for the high-pressure range have represented nothing more than extrapolations of the low-pressure data, with the methane line serving as a general guide. The reliability of these charts has become increasingly doubtful (and critical) in our present technology as we handle more high-pressure systems. The portion of our high-pressure hydrate research program reported here was designed to: (1) investigate the reliability of existing charts; (2) obtain actual data on gas mixtures to 10,000 psia; and (3.) develop a simple hydrate correlation that was more reliable than those which simply used specific gravity as a parameter. Binary mixtures of methane and ethane, propane normal butane, or iso-butane were injected into a high-pressure visual cell containing an excess of distilled water. Hydrates were formed and then melted to observe the decomposition temperature of the hydrates at pressures from 1,000 to 10,000 psia. EQUIPMENT The equipment consisted of a Jerguson 10,000-lb high-pressure visual cell, a 10,000-1b high-pressure blind cell and a Ruska 25,000-1b pressure mercury pump. The visual cell was placed in a constant-temperature water bath controlled by a refrigeration unit and an electric filament heater. A Beckman GC-2 gas chromatograph was used in analyzing the gas mixtures after each run was completed. EXPERIMENTAL PROCEDURE After evacuating the gas system, the heavier hydrocarbon was injected into the high-pressure mixing cell to that pressure necessary to give the desired composition. This cell then was pressured to 1,100 to 1,200 psia by methane from a high-pressure cylinder. The mixing cell holding the gas contained a steel flapper plate and was shaken intermittently over a period of 15 minutes. After mixing, the valve to the high-pressure visual cell containing excess distilled water was opened, and the gas mixture was allowed to flow into the cell. The temperature in the water bath was lowered 10" to 15&apos;F below the estimated hydrate decomposition point. As a first check, the temperature was increased at a rate of 1°F every six minutes to find the approximate point of decomposition. It was again lowered 1.5° to 5°F to form hydrates. The temperature was raised to within l° of the estimated decomposition point and then increased 0.2F every 10 to 15 minutes until the hydrates decomposed. This procedure was repeated at various pressures to obtain 7 to 13 points for each mixture between 1,000 and 10,000 psia. After completion of the hydrate decomposition tests, the gas mixture composition was analyzed with a calibrated gas chromatograph. These gas analyses have an estimated error of ± .1 per cent.

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.&apos; IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470&apos; C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" (&apos;. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923