Search Documents

By Harold F. Unger, Byron S. Snowden, William H. Engelmann

The effects of using surfactant solutions while diamond drilling in amygdaloidal basalt of the Upper Michigan copper mining district were investigated. Nonionic, anionic, and cationic surfactant solutions, all biodegradable, were tested with size AX surface-set bits mounted on a drill instrumented for continuous recording of thrust, rotational speed, and torque levels. Water flow and penetrations rates were also recorded. A drilling study was carried out, testing two rotational speed levels, two diamond bit grade levels, and four flushing agents (including water as a control). Comparison of all low-speed/high-thrust groups of tests shows that the non-ionic surfactant produced a 35% overall average increase in penetration rate over water, the anionic a 29% increase, and the cationic a 28% increase. These increases in, penetration rates resulted in a 22 to 26% reduction in cost over flushing with water alone. With the high-speed/low-thrust combination, the surfactants produced less benefits in penetration rate increases over water (14% increase for nonionic, 14% decrease for anionic, and 2% decrease for cationic type). Particle size analyses were run on drill cuttings produced by the three surfactant solutions and by water. All surfactant solutions showed a 20 to 50% increase in solids content over that of water alone. Since flushing rates were constant, these increases in solids content agree well with the penetration rate changes. The diamonds were recovered from each bit by matrix dissolution, and bit wear was measured in terms of total loss of weight. Flushing with surfactant solutions showed a savings in bit wear in most cases. The drill team noted also that surfactant flushing improved recovery of drill core by allowing easier removal of the core from the barrel.

Jan 1, 1976

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

By P. Barnes

The sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus he obtained of the facts embodied in the statement as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying arid compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

By P. Barnes

THE sums given in the accompanying table are those actually paid for material and labor up to about August, 1875; but, as some parts of the machinery were not wholly completed at the starting of the works in September, 1875, the statement cannot be taken as an absolutely correct note of the total cost. A complete description, with engravings of the building and machinery, was given in Engineering, April 26th, 1878, in a paper by Messrs. A. L. Holley and Lenox Smith, to which convenient reference may be made. A detailed list of the construction accounts has been given in a paper, by the present writer, in vol. vi, Transactions of the Institute. A summary is given in the table of the items in each class which enter into the total cost, and also a note of the proportion which each of these items forms of the whole. A concise view may thus be obtained of the facts embodied in the statement, as a whole, even though it cannot lay claim to completeness in showing the entire or final cost. An urgent suggestion has reached the writer from a distant country that such statements of cost to be really most serviceable should give the details in days of labor, in weight of iron, and in number of brick, and to this an assent is most cordially yielded. It is true, however, that the mere labor of copying and compiling these details to such a degree of minuteness, would be very great, and, in any event, the probable difference between the plans of an existing establishment and one projected, would be so wide as to render even so complete a statement of cost of little more real service than the approximate notes given herewith.

Jan 1, 1879

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Engineer. Graduate of Colorado School of Mines, 1912, experienced in coal, lead manganese and limestone mining, wishes execu¬tive position. A-2146. Graduate Mining Engineer.-Discharged, reserve officer, age 32, single, 7 years' experience holding responsible executive positions, in iron, copper, and talc mining. Well recommended. A-4913. Mine Manager, Superintendent or Engineer. Age 41, graduate of Michigan College of Mines; 20 years' experience in responsible positions in connection with large operations; in iron, copper, pyrites, lead and zinc mines; successful in finding and developing orebodies, increasing production, and reducing costs. Desires a position with a future. A-4081. Mining Engineer.-Graduate from Polytechnicum, Stockholm; 14 years' practical experience in Sweden, United States, Belgium, and Spain, in iron-ore development, mining, and milling; thorough knowledge of English, French and Spanish; desires position as superintendent or assistant manager. Good references; member; now in Sweden. A-4914. Research Engineer. Now in Chile on the erection of a 50-ton mill with modern machinery for the treatment of Chilean nitrate. Desires connection from the first of next year; with firm operating in South or Central America. A-4915. Metallurgical Engineer. Junior member, age 26, single, graduate Columbia School of Mines; recently discharged as lieutenant in the heavy artillery. A-4916. General Superintendent. Technical graduate, age 35, desires position over a group of four or five mines or as assistant general superintendent for a large. company. Has had experience in superintending mines, construction work, opening new and abandoned mines, safety and effi-ciency engineering and handling organized labor. At present employed by a coal company in the middle West. A-4917.

Jan 11, 1919

By C. R. Kuzell

GEOGRAPHICAILY the industry of reducing and refining of copper continued to migrate from the .United States during 1931. While this country is losing the predominant position of its copper industry, our engineers still enjoy their pre-eminent position as leaders in the design and operation of the new plants being brought into production in the four quarters of the globe. Progress in the art, as indicated by the construction of the recently completed works, has not been revolutionary. Standard methods have been followed, augmented by novel features in flow-sheets demanded by the results of progress in the art of ore-dressing, and by reason of problems incidental to the peculiarities of the new ores being treated. Design and construction progress has likewise been orderly and without radical departure from less recent practice; new features in primary and secondary equipment being logical developments to provide for special conditions to keep abreast of improve¬ments in accessory apparatus. The new plants are being rapidly brought in without hazardous novelties and for the purpose of yielding the principal ingredient, copper, in as large a volume as it will he possible to market; the old United States procedure. In the meantime the domestic plants are shut down or operating at a very low capacity, threatened with untimely demise unless the metallurgist can extract and develop other valuable products from the ores. International agreements .and tariff protection may be a temporary reviving stimulant, but for many mines the days of profit will be numbered unless the ores can be made to yield as values the ingredients now being discarded. Invisible progress in this direction has been made during the past year, and it is to he hoped that time will prove that the outstanding progress of 1931 was in the development of processes for the ultimate recovery of by-products from copper ores, perhaps even relegating the value of the copper yield to secondary importance.

Jan 1, 1932

By John Branner

FIVE of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no, evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. PERMIAN Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhão on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about 'the origin of some of the rocks:. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of São-Paulo, Paraná, and elsewhere farther south, but wells drilled in the Permian of São Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian government, in the Permian of Paraná near Marechal Mallet, close to latitude 26° south, but thus far oil has not been found.

Jan 6, 1922

By W. Geo. Waring

Introduction THE winning of zinc and lead ores from the comparatively shallow deposits of the Joplin district, presents, few such problems for the mining engineer as are encountered in deep ore mining and in the handling of complex ores. However, for those who are interested in the origin and nature of ore deposits in general, there is much here to investigate, and upon studies in this direction will depend in no small measure the future of an industry that has produced during the year 1916, in southwest Missouri, lead and zinc ores to the value of $26,319,383; adding $46,022,164 to the metallic wealth of the nation. Including the adjacent mines in Ottawa County, Oklahoma, and Cherokee County, Kansas, which are, really continuations of the Joplin district, the total value of ores produced reached the sums of $34,089,503, and that of the metals, $58,927,941.1 The ores produced in the Joplin district are remarkable on account of their almost uniformly high" metal content in both lead and zinc. Their superiority in this regard is unparalleled, and is doubtless clue to certain geological conditions that are now possibly explicable, provided that the artesian circulation = ascension hypothesis of the origin of the ore deposits is proven beyond question to be the only tenable explanation of the facts. These, as well as other valuable zinc-ore deposits, are bound to he exhausted in time, for ordinary mining purposes, acid it concerns the mining engineer that the conditions under which ores of this character were actually deposited in the form in which they occur, may, if possible, be ascertained, in order that he may learn where to look for similar deposits in other regions, or even how to reproduce artificially such condi-

Jan 9, 1917

William Clinton Brown, Brooklyn, N. Y.: The demand for an apparatus for cooling water for condensers, refrigeratingmachinery and air-compressors, as well as water-jacketed furnaces, has led manufacturers to put such an apparatus on the market, so that it is now possible to purchase a cooling-tower, properly designed and constructed, by simply stating the amount of water to be cooled and the temperatures of the hot and the cold water. The principle is similar to that described by Mr. Henrich, but wood is not used in the best apparatus. There are two great objections to wood: First, it cannot last long under the very trying conditions to which it is subjected; and second, it absorbs the organic matter with which water in constant use becomes impregnated, and the resulting odor is very disagreeable. A few days ago I saw a cooling-tower and condenser, built by the Henry R. Worthington Co., in operation at the Edison electric-lighting station in Brooklyn, N. Y., cooling the water for a 700 horse-power condenser. It consisted of a large stack of iron, about 15 feet in diameter by about 30 feet high. This stack was filled with tiling through which the water falls. A whirligig distributes the water evenly over the top, and a large fan, about 6 feet in diameter, driven by a 10 horse-power electric motor, blows air into the bottom, thus giving a positive circulation. The water, in running down the sides of the tiling, is met by the blast of air, and enough is evaporated to cool the rest. The vacuum-gauge on the condenser showed 26 inches; so the condenser was undoubtedly getting sufficient cool water.

Jan 1, 1896

By J. R. Linney

THE Eastern Magnetite Industry produced approximately 7,850,000 long tons of crude ore in 1945 from which was obtained approximately 3,650,000 long tons of shipping product or a ratio of 2.10 to 1. Lack of skilled or experienced miners was the greatest handicap. Veterans returning to work improved the underground labor shortage in some localities but as a whole the labor shortage was keenly felt throughout the industry. One cannot now predict what may be accomplished in 1946 but barring major steel strikes a worthwhile improvement can be expected. At the Richard mine of the Richard Ore Co., the shipping product for the year amounted to approximately 124,650 long tons of concentrate and lump ore. Crude-ore production was 160,600 long tons. The average analysis for lump ore was 63 per cent iron and for concentrates 66.05 per cent. The Warren Foundry and Pipe Corp. at their Mt. Hope mine produced 73,000 long tons of lump ore averaging 59.5 per cent and 57,000 long tons of concentrate averaging 67 per cent. The total mine hoist was approximately 209,000 long tons. Operations were commenced through the new Leonard shaft on Jan. 18; the Brown shaft through which operations had been conducted since 1912 caved beyond repair on Sept. 26. No one was injured but pumping facilities were somewhat disrupted. In order to reach designed capacity a total of 400 men will be required with 300 underground. Due to shortage of labor all operations in 1945 were concentrated on the 1700 level. As fast as men can be hired and trained development of the 2100 and 2500 levels will commence. Mt. Hope has a consider-

Jan 1, 1946

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

The Delegation of American Engineers constituted by the American Institute of Mining and Metallurgical Engineers, the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers, that visited France in December, 1918, in acceptance of the invitation extended by the Congrés General du Genie Civil consisted of the following: Representing the American Society of Civil Engineers, Major James F. Case, past president, Geo. F. Swain, vice-president, Nelson P. Lewis, treasurer, Geo. W. Tillson, past director, Geo. W. Fuller, director, A. M. Hunt. Representing the American Society of Mechanical Engineers, president, Chas. T. Main. Representing the American Institute of Electrical Engineers, past president, L. B. Stillwell. Representing the American Institute of Mining and Metallurgical Engineers past-president, E. C. Spilsbury. The delegation organized on the way over by the choice of Major James F. Case as chairman, and Geo F. Swain as secretary. On arriving at Bordeaux, the Delegation was met by Mr. S. D. Brown, associate member of the American Society of Civil Engineers; and on its arrival in Paris it was joined permanently by the following attaches: Captain P. Charton, of the French Engineers, Delegate of the Commissariat-General to accompany the Delegation and serve as liaison officer; Captain Carpenter of the American Army; and Mr. Geo. Herdt, representing the Society of Civil Engineers of France. The object of the visit was to discuss with the French engineers the large engineering, problems now facing France. Engineering problems in their restricted technical sense came up for discussion practically not at all, for the French do not need advice nor assistance along strictly scientific lines. It was in the -larger and economic aspects of engineering, to aid in building up the industries and commerce of France, that our French associates desired to learn from the experience of the American Delegation.

Jan 9, 1919

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75' to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.' The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954

By A. L. Titchener, M. B. Bever

FROM their investigation of the martensitic transformation in Cu-Zn alloys, Greninger and Mooradian' concluded that there was no critical temperature at which martensite formation began in this system. Recent unpublished work by Gen-evray With two compositions of brass revealed the existence of a critical temperature, which is a function of composition and stress. In the work reported here the temperature range of the martensitic reaction was studied as a function of composition in high purity Cu-Zn alloys. The specimens were about 4 in. long with a diameter of 1/16 in.; their compositions are given in Table I. They were heated under vacuum for 5 min at 5" to 10°C below the temperature of incipient melting, and quenched into brine at about — 10°C. Specimens of alloys C, D, E and F were obtained with little or no precipitated a phase. Many attempts yielded only three usable specimens of alloy B, and even these contained appreciable amounts of a. All efforts failed to preserve metastable p in alloy A (containing 38.02 pct Zn and 0.002 pct each of Pb and Fe). The transformation was studied by measuring the electrical resistance during continuous cooling and heating of each specimen at similar rates. The cooling media were alcohol with dry ice from room temperature to — 78°C and a bath of petroleum ether and methyl cyclohexane (75:25), cooled by liquid nitrogen, from —78" to about —150°C. Readings were also taken at —195 °C in liquid nitrogen. Fig. 1 illustrates a typical experiment. The relative resistance is obtained by assuming the known

Jan 1, 1955

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By H. R. Hanley

ONE of the most important contributions to the art of electrolytic zinc production-has been the aluminum cathode. This has been used in all major production: since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi-menting on the extraction of-zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent-No. 20073. The reason for this dominant position of aluminum as cathode mate-rial in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as arc tine copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a .few hours of deposition, and thus special arrangements must be made to compensate for this abnormality.

Jan 1, 1938

By V. C. Smith

Reliable and detailed statistical data available for Kentucky, Ohio and West Virginia are the most meager and unsatisfactory of any of the producing states. Detailed histories and statistics are available for only a few pools. The antiquity of these pools, loose nomenclature, particularly where several names are applied to the same pool or various parts of the pool or a new namsed when the pool was rediscovered, made the collection of accurat historical and statistical data almost impossible. So many of the data reported are unreliable that a breakdown by pools or even by counties, until more accurate information is available, would lead to gross errors. Rather than perpetuate inaccuracies, we have endeavored to go to original sources wherever possible, sift these and provide data that may serve as an incentive and basis for future work. The necessity for accurate information is thoroughly recognized by the operators, particularly because of the effect of recent government regulations and request? for data in connection with the preparation of the various codes a pending legislation. Producers, both major operating companies and individuals, . freely given their time and assistance in the compilation of these data. Valuable information was obtained from tax records, rate cases, statistics published by the oil and gas publications and the Bureau of Mines. So many individuals cooperated in the preparation of these data that individual credit cannot be given. Undoubtedly many errors will be found. Some of the data are open to controversy, and many have been omitted in the hope that new information of a more reliable character may become available. Other omissions are due to an inability to contact the proper individuals, many of whom are no longer connected with this industry. Pennsylvania grade crude sold in 1933 for the lowest price since 1895. Gas production could not find sufficient new markets to fill the void left by industrial stagnation. In the gas industry, where the market price is fixed by contract, uncertainty persisted because of impending legislative action affecting both taxes and utility rates. As a result of these factors and a lack of new money, drilling was restricted to a new low. The lifting of proration toward the end of the year in the Pennsylvania

Jan 1, 1934