Search Documents

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW YORK, N. Y. BENJAMIN B. THAYER,2 NEW YORK, N.Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,' NEW YORK, N. Y SECRETARY EMERITUS ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 6, 1915

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By J. H. Bucher

The effect oj strengthening by the precipitation of CbC on the toughness offerrilic steel (0.11 pct C, 0.74 pct Mn, 0.02 pct Cb) was stlrdierl. A g-veater degree of pvecij~itatiotz strengthning is ohtaznable by aging the so11ution-treated steel rtt velaticely Low temperature was (1050" to 1l0O3F) than at higher temperatures (I150" to 1200°F). Tlzis ),eslrlts because a finer dispersion of CbC is obtained. However, the ductile-brittle transition te~ripertltlo.e is raised approximately tlzjeee tirues as IFLIIC~ perv a given yield stress increase) by aging in the lower tempareture range, as opposer1 to the Irigher temperaturee range. This is proposed to result pl-iir~avily because different precipitation distributions ar-e associated with the different aging -treaments. For tile steel aged at 1050" and 1100 F, heavy: precipitation on disloccctions occurs resulting in a high degree of rlislocution pinningh tl~us lowevirzg- the toilguiess. in tll c(.rise of the steel aged at 1150 'a?zd 1300"F, Pvecipitatiol~ is irzove g-enerally distributed throughout the matrix rather limn preferentially on dislocations.; and Ike detlsitj, oj mobile dislocations is not sttyong-ly affected. THE most effective means of strengthening hot-rolled ferritic steels are grain refinement and precipitation hardening. It is well-known that grain refinement increases both the strength and the toughness. However, the upper limit of yield strength obtainable by grain refinement alone is about 60,000 psi,'12 i.e., without the formation of acicular structures of lower toughness. The most economical means of obtaining higher strengths is the addition of small amounts of elements such as columbium, vanadium, and titanium which form carbonitrides. These precipitates are very effective in increasing the strength, but the ductile-brittle transition temperature is is Although it is agreed upon that precipitation decreases the toughness, there has been little effort to isolate the causative aspects of embrittlement. The purposes of this research are to assess quantitatively the embrittlement associated with different precipitate distributions and morphologies, and to correlate the degree of the embrittlement with the microstruc-ture. In this manner, a more fundamental insight into the mechanism of embrittlement may be gained. The steel selected for this purpose was a low-carbon, columbium-bearing steel which, after solution treatment, was aged in various time-temperature cycles while attempting to hold all other microstructural variables constant. MATERIALS AND PROCEDURE The composition of the steel used in this investigation is given in Table I. Starting with commercially hot-rolled material 0.074 and 0.280 in. thick, tensile blanks were cut from the thinner material and sub-size Charpy blanks from the thicker stock. The steel had been rolled using a low finishing temperature and rapid cooling after hot rolling to produce grain refinement. Also, chemical-extraction analysis and electron-microscopic examination revealed that the cooling was rapid enough to suppress any significant precipitation of CbC. Therefore, the as-rolled steel is essentially in the solution-treated condition in terms of the precipitation reaction, and it was used as the base material in this investigation. The room-temperature tensile properties of the as-rolled steel aged at 1100", 1150", and 1200°F for various time intervals were determined, see Table 11. The ductile-brittle transition behavior was studied for smooth and notched tensile specimens, and longitudinal half-size (0.200 in. thick) Charpy V notch specimens aged at 1100" and 1150°F for various times, also Table 11. In addition, tensile specimens aged for single times at 1050" and 1200°F were evaluated with respect to their ductile-brittle transition. Only one 1050°F treatment was used because of the extremely slow kinetics of precipitation at this temperature and because no significant difference between 1100°F aging was observed. Only one treatment at 1200°F was used because aging at this temperature alters the shape of the grain boundary cementite particles present in this steel and complicates analysis. The design of the tensile specimens is given in Fig.1.

Jan 1, 1968

By T. H. Watkins

COAL is the basis upon which the activities of the industrial nations of the world rest today. In order that the coal industry may bee restored to a reasonably healthy condition, it is essential that both the operator and the miner should understand that they are directly concerned and that their selfish interests demand that they take an active, intelligent, self-sacrificing view of the entire situation and do their part in restoring and repairing the economic structure. Foreign credits, foreign debts, unstable exchanges, destroyed markets, and inability through lack of credit to carry on as before, all require our attention and cooperation. DEEP CONCERN AS TO FUTURE There is deep concern as to the future and a realiza-tion on the part of some of these leaders of industry that they will have to sacrifice their personal time, away from their desks and the details of business, in order to cooperate with other groups in studying the situation and endeavoring to find the best method of utilizing their knowledge in improving conditions and averting further disaster. It is most unfortunate for the country and for labor itself that the labor chiefs are blind to these necessities, and hostile to every effort to secure their cooperation in rebuilding prosperity.

Jan 2, 1922

By Milton F. Goodrich

The idea of using water-only cyclones to scalp clean coal from the feed to other devices has recently been gaining in popularity.l,2,6 An indication of this popularity is that water- only cyclone scalping is already employed in a few commercial plants. Water-only cyclones scalp the feed to a heavy media vessel in the Warwick plant,3 to Deister tables in the Rowland plant,4 and to a heavy media cyclone circuit in the Amherst Coal Company's McGregor plant.5 Despite this trend, we found surprisingly little information in the literature on the performance of water-only cyclone scalping. Therefore, we undertook a study of its technical merits, limiting our investigation to a water-only cyclone scalper in conjunction with heavy-media cyclones. We felt this to be a reasonable combination of equipment, since both processes operate well on the same size coal. First, we developed simple mathematical relationships revealing general characteristics of the system. Next, we compared the clean coal yield and quality obtainable by the system on four different coals with that obtainable by heavy-media cyclone circuit alone and water-only cyclones middlings recirculation circuit alone. This was done by using computer program to simulate the operation of the three systems. Finally, we considered the effect that implementation of the system would have on a typical preparation plant circuit.

Jan 10, 1978

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

ROBERT F. MEHL, Chairman ALBERT J. PHILLIPS, Past-chairman ROBERT H. LEACH, Vice-chairman E. M. WISE, Vice-chairman W. M. CORSE, Treasurer - Louis JORDAN. Secretary 29 West 39th St., New York, N. Y.

Jan 1, 1938

TULSA SECTION At the smoker concluding the two day meeting of the Tulsa section of the American Institute of Mining and Metallurgical Engineers, Tulsa, Okla., Feb. 26, 1919, Dr. Willis T. Lee, the new head of the Geological Department of the University of Oklahoma, was introduced to the assembled geologists and mining engineers. Dr. Lee requested that the geologists and engineers who were making a specialty of petroleum geology assist him in giving a good course in practical oil geology in the Geological Department of the University. After a motion offering the services of all present in giving lectures on their special subjects had been adopted, Dr. Perrine of Hutchinson, Kans., named the geologists who were pledged to give lectures in Dr. Lee's course. The students in geology at Norman are assured of the latest information regarding practical work in petroleum geology and will have the inspiration derived from contact with men who are actually at work upon the problems which they are studying. Dr. Lee and President Brooks of the University are to be congratulated upon the introduction of this .method of instruction. The plan thus put into operation is similar to the graduate system of coaching in athletics followed at many of the large universities; what is good for instruction in athletics should also prove good for instruction in applied geology.

Jan 6, 1919

By AIME AIME

FOR the use of workmen and employees, the company should establish a dispensary and a -hospital where workmen who suffer accidents or professional diseases may be taken care of; and at suitable places in the mine or metallurgical plant it should install first-aid stations. Workmen have a right to receive 75 per cent of their wages while they are unable to perform their work as result of a professional disease; but some companies pay full wages and in the case of natural disease, with the exception of venereal, alcoholism, injuries from fights, and chronic illnesses, 50 per cent of their wages up to a period of two months. The number of diseases the Law considers as professional is large and increases almost daily. Among the professional diseases, the one which has caused greatest harm to the miners and expense to the companies is silicosis. To avoid its propagation, companies should take every possible precaution that the working atmosphere is free from dust, abating this by frequent sprinkling of the workings using, wet drills and furnishing the workmen adequate protective apparatus such as respirators.

Jan 1, 1937

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

President-Mrs John R C Mann, 90 Edgemont Road, Scarsdale, N Y First Vice-President-Mrs C P Pollock, 27 Dante Street, Larchmont, N Y. Second Vice-President-Mrs Mendum B Littlefield, 40 Lincoln Street, Larchmont, N Y Third Vice-President-Mrs J B Cunningham, 236 East 2nd St , Tucson, Ariz Fourth Vice-President-Mrs Theodore Loftus, 410 Cowles St, Fairbanks, Alaska Fifth Vice-President-Mrs George L Craig, 109 Calumet Avenue, Calu¬met, Mich Recording Secretary-Mrs Arnold H Miller, 601 West 115th St, New York 25, N Y Assistant Recording Secretary-Mrs R J Mechin, 66 East 79th St, New York 21, N Y Corresponding Secretary-Mrs John A Poulin, 4 East 70th St , New York 21, N Y Treasurer-Mrs Robert W Rowen, 29 West 39th Street, Room 914, New York 18, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 1000 Park Avenue, New York 28, N Y Assistant Treasurer-Mrs Roger H Sherman, 8 Roman Avenue, Forest Hills Gardens 75, N Y.

Jan 1, 1957

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of' density. A serial sectioning' technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski' in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners' Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917

By R. U. Fitting, A. C. Bulnes

Field experience with limestone and sandstone production indicates the existence of wide differences between the reservoir behavior of these two types of formation. Little attention appears to have been given to the separate study of the flow of fluids and the retention of fluids in limestones. This paper presents data and arguments to demonstrate the existence of a difference between the two types of formation, and urges the separate intensive investigation of limestone reservoirs. AH experimental data presented pertain to dolomitic limestone formations in west Texas and New Mexico. Two kinds of Porous media are recognized— intergranular and intermediate. Intergranular rocks are those in which the porosity and permeability are determined by the geometrical properties and the sorting of the sedimentary units; intermediate rocks, those in which there is no direct relationship between grain properties and the porosity and permeability. Limestones in general are intermediate media. The partial relationship between porosity and permeability of any class of Porous media is represelried by an area of .finite extent and definite shape on the permeability-porosity plane. The horizontal and vertical variations of porosity and of permeability in limestone and sandstone formations are discussed and compared. Comparisons are made of connate-water content, the relative permeability-saturation relationship, and capillary phenomena in the two kinds of rocks. A number of tentative conclusions are drawn relative to the reservoir properties of lime- stones; in particular, (I) dolomitic limestones are oil bearing and apparently are oil productive in zones of permeability less than 0.1 millidarcyj and (2) primary depletion (by gas expansion) oil saturations may be lower in dolomitic limestones than in sandstones. Introduction It is well known that the reservoir performance of limestones displays numerous irregularities when compared with that of sandstones, and that the departures from "normal" behavior of limestones are more frequent and generally more marked than in sandstones. This is particularly true of fractured limestones and those that have undergone considerable development of secondary porosity' A review of the literature of production research published during the past 15 years reveals a startling absence of theoretical and experimental investigations directed specifically toward explaining and predicting the performance of limestone reservoirs, even. though such problems as the prediction of water encroachment and the estimation of ultimate recoveries continue at the "inspired guess" stage. By far the greater part of the experimental data reported pertain to measurements on sandstone core samples, while the theoretical studies, almost without exception, are developed from the assumption of an ideal porous medium and therefore seldom are applicable to limestone formations. The chief cause of this situation appears to be the common belief that, to all practical intents and purposes, sandstones and the majority of producing limestone formations

Jan 1, 1945

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.1, 2' To effect satisfactory separation of the gangue, pre-dominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose.V here is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential," and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products. Ore Preparation The ore used in this experiment was a wash-ore tailing obtained from the western Mesabi range. Microscopic examination and x-ray analysis of the ore showed it to consist of hematite, goethite, and quartz. Physical properties of the iron minerals ranged from hard and crystalline to earthy and ocherous. The quartz grains were discolored either because of iron-oxide inclusions or because of a sur-face coating of iron oxide. The ore assayed 27.52

Jan 1, 1954