Search Documents

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By Frank F. Aplan

In looking into the crystal-ball scene of minerals beneficiation for 1970 and beyond, an impartial observer becomes con- fused as to what has been done and what is possible in the way of improvements. The mining official must balance the burden which is being shouldered by the mineral industry for maintaining our environment in its pristine state on one hand, with the solid advancements made in technology and cost savings on the other hand. Then the official wonders if this is really the criterion for judging overall performance today. As a prospective engineer, Dave Bolles sees it this way: "Specialization has caused many engineers to subordinate everything to doing their job the cheapest and fastest way. In the future this won't be enough. The engineer in the mineral industry will be responsible not only for mining, concentrating and smelting, but also for the resultant wastes- the mine dumps, the tailing dams and the slag piles." (See Drift on page 63).

Jan 1, 1971

By Robert F. Mehl

THIS essay is an attempt to present the elementary facts and ideas concerning the growth of crystals, especially of metals. Freezing, like all heterogeneous processes, is a process of nucleation and growth; it manifests itself in metallurgy primarily in the freezing of ingots. The preceding paper in this volume discusses nucleation; the paper to follow describes ingot solidification. The present paper will treat of the growth of nuclei to large crystals, embracing a long series of phenomena, many of which are familiar to metallurgists.† Crystal growth, it will be immediately noted, occurs not only in the freezing of metals, but in the freezing of all substances; and it is a prominent and familiar phenomenon in crystallization from solutions, aqueous or otherwise, and in crystallization from the vapor phase. It will be necessary to include such systems in this discussion, for so much of value to metallurgists has been learned from their study. Apart from this, so far as metals are concerned, it will be simpler to limit the discussion to the freezing of pure metals and of solid solutions. Other types of freezing-eutectic, peritectic, etc.-will be excluded, though they have much of interest and of importance. BASIC MECHANISM OF FREEZING Ideally, nucleation and growth processes can best be considered from the point of view of isothermal reaction and upon the assumption of random nucleation. In. such an ideal case, nuclei form at random, and at a characteristic rate either constant or changing with time, and grow to spherulites at a characteristic rate, constant or changing with time, Fig. I.. On the simplest assumption, the reaction rate-in this case the rate of freezing-is a resultant of these two component rates. The reaction rate equation may be written in terms of these two component rates. The formation of pearlite from austenite closely approaches this ideal case. The ideal case forms a very useful point of departure in considering real cases. Various factors of reality produce deviations from this assumed ideality. In freezing, the isotropic medium, the melt, passes to the anisotropic solid, the crystal. Crystals are lattices of atoms, and the unit cell is often referred to as a crystal unit. Rosenhain, many years ago, represented the nucleation and growth process on freezing in the manner shown in Fig. 2, feeling, intuitively, that there must be some crystal unit in crystal growth. It now appears that this may be true, though his picture requires much elaboration. The greatest deviation from ideality lies in the nonisothermal nature of the freezing process in metals. To approach this properly it should be recalled that many nonmetallic substances freeze slowly. Tammann, to whom we owe the classic approach, studied complex organic materials in which (as in the case of eutectoid steels at high

Jan 1, 1951

By Raymond Ward

Jan 1, 1945

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By Robert S. Williams

On several occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825" C. and is then reheated, the writers have noticed that reerystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens 1 in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840' C. for 2 hr. and then quenched ' in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen and duplicate observations were possible. The specimens were held at the reheating temperatures for periods of 15 min., 30 min., 1, 2, and 4 hr. All specimens were etched with a freshly prepared mixture of equal volumes of concentrated NH4IOH and H2O2.

Jan 1, 1924

SECTION I Page Page Manuscript Closing Date, Febru- Forthcoming Meetings xxvii ary Meeting v . Library xxviii New York Section War Meeting on Membership xxxii Ferro-Alloys v Biographical Notices: Minutes of Meeting, Board of Robert Bell, by F. D. Adams. xlix Directors xvii H. J. Cantwell, by H. A. Members in Military Service xviii Wheeler 1 Personal xxiii Institute Committees Iii Employment xxv Officers and Directors Ix

Jan 11, 1917

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By S. D. Michaelson

[CONTENTS PACE See TP 2377, Min. Tech, May 1948 for discussion of A Technique for Photographing Difficult Subjects through a Petrographic Microscope (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL). Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy (TP 2141 by R. A. ....... PALLANCH, Min. Tech:, March 1947. Discussion by S. D. MICHAELSON). I Symposium on Milling Devices and Practices. (TP 2162 by J. F. MYERS and R. J. TOWER, Min. Tech., May 1947. Discussion by HARLOWE HARDINGE). ............ 2 Rod Milling-Plant and Laboratory Data. (TP 2175 by J. F. MYERS, S. D. MICHAELSON and F. C. BOND, Min. Tech., July 1947. Authors' supplement and discussion by HARLOWE .......................... HARDINGE, and B. H. IRWIN) 2 A New Separating Vessel for Sink-float Concentration. (TP 2182 by E. C. BITZER, Min. Tech., May 1947. Discussion by E. H. CRABTREE, JR.) .................. 5] Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy S. D, MICHAELSON*-The method of determining the efficacy of a separation described in this paper, gives the metallurgist a most useful guide for keeping his ship on an even keel When the ore Waves vary from placid seas to high breakers. Now that such a method of evaluating metallurgical efficiency has been developed and proven practical, it Would seem logical to introduce the next, and more final, factor of Economic Efficiency. I choose to define this term as the percentage ratio of net return from milling to the theoretical maximum net return. The actual operating cost subtracted from the actual mill return represents the net actual amount received for the material treated. Experienced operators of most plants Would ordinarily have enough data on hand to estimate a theoretical milling cost per ton, based on labor, power, supplies and maintenance When operating at maximum tonnage With minimum trouble and under ideal ore conditions. When this theoretical estimated cost is subtracted from the theoretical maximum ore return (calculated by Pallanch's method) the resulting figure is the maximum theoretical net amount the mill operator could hope to realize in processing the ore. The percentage ratio of these sums, of actual to theoretical, is the economic efficiency of the operations. This economic efficiency, if determined on the basis of a fixed market price for metal and similarly fixed base rates for labor, power and supplies, Will reflect the effect of changes in milling practice, labor efficiency and equipment condition. When computations made on the basis of actual current rates for labor, power and supplies are compared With similar actual figures for past periods they will show forcefully how energetic our hunt must be to develop man saving controls, more effective metallurgy, and better equipment to maintain profitable operations. Such computations also offer a simple means of determining how much more labor, supplies and power can be put into the mill operation to obtain an increase in metallurgical recovery at a profit.

Jan 1, 1947

Photographs of Officers

Jan 1, 1923

By M. L. Holzworth, Philip R. Sperry, Paul A. Beck

INTRODUCTION THE basic work of Z. Jeffries1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria have been added, Jeffries found that grain growth was inhabited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. Such a "coarsening temperature" was later found by Gross mann13,14 in certain types of steel, while Bain showed" that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work16,17,18,19,21 demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently.20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases, with the titanium content. That coarsening may occur, as a result of certain heat treatments, even in low carbon rimmed sheet steel, was shown by Samuels,22 He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material, In this instance the identity of the inhibiting phase has not been determined, However, Tangerding found 23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction, The carbide particles can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air, is followed by annealing in hydrogen for 75 hr at the same temperature, grain growth is more spectacular; usually the whole specimen is transformed into a single crystal (approx. 1,5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth resulting from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced during the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pct Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1948

By G. Willard Quick, John R. Freeman

Jan 1, 1930

By Homer Turner

THE nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.1 Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties.

Jan 1, 1929

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937