Search Documents

By Xihuai Gong, Hongshuang Di, Jianping Li, Ning Yan

In this work, we investigated the effect of the rolling process (warm-rolled or cold-rolled) on microstructure evolution and mechanical properties of 9Mn steel. After intercritical annealing at 670°C for 10min, both cold-rolled and warm-rolled microstructures are composed of ultra-fined austenite and intercritical ferrite. The austenite in warm-rolled sample includes two types of morphology, namely equiaxed and lamellar, which exhibits a wide distribution of grain-size. The incomplete recrystallization or recovery behavior of ferrite in warm-rolled and annealed sample results in higher yield strength and shorter yield point elongation. Moreover, the warm-rolled and annealed sample extends the TRIP-related work hardening over a broad strain range, resulting in a better combination of ultimate tensile strength and total elongation.

Oct 1, 2019

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By José Adilson de Castro

In the integrated steel industries the sintering process plays an important role furnishing raw material to the blast furnace. In this work, a computational simulation of the sinter process is developed that is able to predict the most important phenomena within the sintering bed. The model is based on the multi phase concept with multiple components described by conservation equations of each component coupled with the momentum, chemical reactions and heat transfer. The model validation was carried out comparing the model predictions with averaged industrial data and local temperature measurements within the sinter strand. The model predictions presented good agreement with the averaged values measured on the industrial sinter process.

Aug 2, 2018

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Aperam South America

Balanço Energético Global e Utilidades - 2013

Jul 31, 2018

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Florian Markus Penz

The increase in Basic Oxygen Furnace (BOF) plants in steelmaking has given rise to renewed interest in a dynamic simulation of the BOF process. Material and process costs can be saved with optimized process times and targeted charging of scrap and slag formers. Beside hot metal, scrap is the main source of iron in the BOF process. Furthermore, scrap is used as a coolant during the process due to exothermal chemical reactions occurring in the BOF. In this paper, the melting and dissolution behaviour of scrap in the BOF process is discussed. A new dynamic thermodynamic and kinetic Matlab® model used to simulate scrap melting behaviour as a function of various scrap surface parameters and particle size is presented, as well as the influence of scrap properties on liquid bath temperature and final crude steel composition after a defined blowing period.

Oct 30, 2017

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Jorge Madias

Neste trabalho se leva a cabo uma revisão da literatura sobre defeitos em beam blanks. O foco é no mecanismo de formação e as soluções propostas para diminuir sua ocorrência. Os defeitos superficiais incluidos são as trincas longitudinais e transversais, bleeding, pinholes e escória. Os defeitos internos levados em conta são os blowholes, as trincas centrais e as trincas nas pontas das abas. A revisão incluie as técnicas utilizadas para pesquisar os defeitos: caracterização metalográfica, CFD, modelagem termodinâmica e termomecânica, etc. As medidas adotadas estãorelacionadas a mudanças no sistema de lingotamento (por exemplo o design da vâlvula submersa), design do molde, mudanças e regulação do resfriamento secundário, suporte dos veios.

Oct 30, 2017

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By George Schipper, Peter Gelten, Pepijn Adriaen, Hugo Uijtdebroeks

Tata Steel IJmuiden Hot Strip Mill 2 (HSM2, 5.5 Mtonnes/yr) is currently being upgraded, resulting in an increased rolling force and motor power capacity. With the current conventional work roll spray cooling, a deterioration in work roll & strip surface quality performance is expected as a result of the increased mill capacities. In order to improve strip surface quality, HSM2 decided to do a full-scale production trial with High Turbulence Roll Cooling (HTRC) at stand FM2. HTRC is a novel way of roll cooling using a high turbulent flow regime. HTRC is positioned very close to the roll surface and gap exit, which is beneficial for the roll surface quality. It is operated at a high flow rate but at a low pressure. HTRC not only significantly improves the roll surface quality, in addition, it makes high pressure pumps, needed for the conventional spray cooling, redundant, leading to substantial savings on electricity costs and thus CO2 emissions. HTRC is in trial operation since 7 August 2018. Results show no operational issues, an excellent roll surface quality and an increased cooling efficiency. In summer 2020 stands FM1-FM2-FM3-FM4 of HSM2 will be equipped with HTRC.

Oct 1, 2019

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019