Search Documents

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By S. Kivrak

The firms in construction industry could not sufficiently adapt the rapidly emerging information technologies in recent years into their corporate structures. Therefore, in an effort to further exploit the benefits of information technology (IT), integration of the experiences and backgrounds of construction industry and the advantages of IT, is one of the most open-ended fields for improvement in this industry. Utilization of IT in the construction sites will positively affect the efficiency, productivity, quality and health & safety issues in the construction sites thus the cost and completion time of the projects. Within this context, augmented reality technology, which brings a new perspective into IT, can be put into the service of construction industry. Augmented reality which has been designed to improve the services in many application domains such as school education, military warfare, military trainings, industrial maintenance, retail and medical, can be defined in the simplest form as augmenting the real world with information from the virtual world. The main aim of this study, which presents an overview of an ongoing project, is to develop an innovative method by making a construction worker, foreman, equipment operator or a site engineer watch a very comprehensive and informative animation which will enable the said staff to perform or supervise all the phases of the activity he or she is in charge for in a more efficient, productive, safer and qualified manner by means of smart glasses using augmented reality systems. In this respect, training material related with the activities in the construction sites will be prepared and with a well-fictionalized scenario, animations exhibiting all the phases and details regarding the related activity (e.g. masonry, formwork and rebar works etc.), method of statement, correct and incorrect applications in comparison-wise manner, will be produced. Therefore, the user will be able to reach the training material, method statements etc. in the animations about the activity he or she is in charge for, enabling him or her to figure out the work as prescribed in the specifications. Basic trainings about the system will be given to target group, i.e. construction workers, foremen, operators, site engineers and managers working in the construction sites to apply the system on sites after all the system was tested. After the testings, to determine the effectiveness of this system, semi-structured interviews and survey questionnaires will be conducted among the mentioned target group. Therefore, the potential benefits of this system to the construction industry can be determined. The main target of this study is to implement an efficient, thorough construction management by orienting the staff in the construction sites to perform efficient, safe and qualified works by means of smart glasses that use augmented reality. There are relatively few studies about the implementations of augmented reality technology in construction. The outputs to be attained in the end of the study have the potential of improvement of time, cost, quality and safety parameters by ensuring a qualified, safe, efficient and productive construction management via augmented reality technology in the construction industry.

Aug 1, 2013

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By McHenry Mosier

This is the fourth progress report in the series on the use of detachable rock-drill bits in the metal mines of the United States. It contains comparative statistics and costs or drilling at eight mines not reviewed in previous reports, comparison of the use of detachable bits at small mines and large mines, a discussion on the life of drill rods, and general conclusions derived from an analysis of the rock-drilling practice at all the mines investigated on this survey. This paper completes the descriptions of operating practice in rock drilling at individual mines. Data on drilling practices at 28 mines are given in appendices I and II and drilling costs are shown in appendix III. Research in the fundamentals of rock drilling, including the use of detachable bits, has been undertaken by the Bureau of Mines in its testing adit at Mount Weather, Va. Reports on the progress off this investigation will be issued when results warrant their publication.

Jan 1, 1937

By J. H. Starkey

SAGDesignTM Testing for grinding mill design was introduced commercially in 2004. Up to January 2008, 18 projects have been completed and 99 samples have been tested using this method. Two papers have been published describing the patented test procedure and one of these shows how the results compare with other grinding test methods. This paper will briefly discuss the theory on which this technology is based, and explain the procedures used to develop the calibration equation. Case studies are also included to demonstrate the effectiveness of the test work being done. These case studies show how the SAGDesign test is being used today: to design new grinding circuits for commercial full scale use; to calculate throughput in existing mills for production planning; and to accurately define grinding mill requirements at the scoping, pre-feasibility or feasibility study stage of project development, in order to economically identify the size and cost of the grinding mills that will be needed for the project. This is important because if the full rec-ommended SAGDesign testing program is done at an early stage in the project, the definitive cost for a guaranteed throughput, grinding mill design (by Outotec if their mills are purchased) is available. New grinding mill design for final engineering will be represented by the test work done on the Climax Molybdenum Project for Phelps Dodge (now FMI) in Colorado, USA. The SAG mill and ball mill for Climax are now in fabrication with project start up in late 2009. Next, the sizing of grinding mills at the scoping, pre-feasibility or feasibility study stage of mine development will be represented by a large metal mining property in Russia. Finally, calculation of the throughput for existing mills will be represented by work done at a base metal mine, in eastern Canada. Test work for designing SAG mills is now done in four laboratories at the time this paper was written. One in the USA at Dawson Metallurgical Laboratories, Inc. in Salt Lake City, two in Russia at the TOMS Research and Design Institute and at the Irgiredmet Research Institute, both in Irkutsk, and a fourth mill has been installed in Australia at AMMTEC Limited?s lab in Perth. A fifth SAGDesign test mill for radioactive ores has been built by Starkey & Associates, specifically for testing uranium ores and can be moved to any licensed lab in the world on a project basis.

Jan 1, 2014

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997

By A H. Clemens, T A. Moore

This paper discusses a number of technical issues related to marketing coal. It outlines how the results of research undertaken in New Zealand and overseas can help producers address a range of technical factors that impact on production costs and marketability. The paper also discusses trends in coal utilisation for power generation and how new technologies may require coal with different characteristics. Research and development into options for CO2 sequestration are discussed including carbon storage in forests, and removal of CO2 from flue or fuel gas in power stations, and its disposal.

Jan 1, 1997

By Peter Zhang

Pumpable cribs are being increasingly used in longwall tailgate entries and bleeders for roof support under abutment pressure. Their high peak capacity and confinement-controlled yield characteristics from reinforced-bags make them relatively safe and reliable standing supports for highly productive longwall panels. The pumpability of crib material over a long distance from the surface greatly reduces material handling and makes the underground installation more efficient and flexible. However, the performance of pumpable cribs is dependent upon crib properties, crib pattern, quality of installation, and geological and mining conditions. For proper crib selection and safe support design, it is critical to understand the basic technical requirements and performance of pumpable cribs in longwall tailgate entries and bleeders. Based on more than 10 years of experience using pumpable cribs for longwall standing support, the requirements and performance of pumpable cribs in longwall tailgate entries and bleeders under different mining conditions are presented. Experience shows that the load-displacement curve from full-scale lab testing is a good indicator of pumpable crib suitability for certain applications. Crib peak capacity, stiffness, and residual characteristics define its applicability to certain gate entries and bleeders under different cover depth. Crib pattern and spacing can be determined by abutment pressure level, roof, floor, and rib conditions, local roof stability, and ventilation requirements. To achieve proper in-situ performance, quality control of crib installation is also important.

Jan 1, 2012

These proceedings consist of papers presented at three Bureau of Mines Technology Transfer Seminars on ergonomics in the mining industry. These seminars were held in December 1981, and covered topics relating to ergonomics and mining in the areas of the man-machine interface, and design of the work environment. This area of research is directed toward reducing accidents traditionally associated with human error.

Jan 1, 1981

By John Convey

"IRON ORE was first smelted in Canada about the year 1736 at Les Forges, Quebec -a most appropriate name for such a historic locale. During these early years of the 18th, 19th, and first quarter of this century, about six million tons of ore were mined and employed in the manufacture of items ranging all the way from kettles, stoves, and cannon for the early settlers to weapons of war for the allied armies of World War I.But this symposium on iron ore is not concerned with this early period. Instead, it is concerned with the iron ore industry of today -an industry which will soon be-come one of the two most valuable mineral industries in Canada.The subject in its broad geographic and economic aspects will be introduced by Mr. Buck; Dr. Harrison will describe the geology and origin of the principal iron ore deposits; Dr. Downes will go into beneficiation as it applies to iron ores; and Mr. Gertsman will discuss primary processing. The symposium will not deal with the steel end of the industry, because that phase itself could well form the subject of a symposium."

Jan 1, 1955

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By S. E. Burton

The White Rock area of the Boiling Springs manganese-iron deposits comprises about 3,200 acres of land in Monroe Township, Cumberland County, Pa. (See fig. 1.) This property was brought to the: attention of the Bureau of Mines by Pennsylvania Geological Survey Bulletin 128, entitled "Manganese Ores of Pennsylvania" by R. M. Foose. It was examined by an engineer of the Bureau of Mines in August 1942 and was further investigated by the Bureau by churn drilling and underground development during the period December 1942 to February 1944. Beneficiation tests were made on samples of the ore. This report describes the work done during the investigation and presents the results obtained.

Jan 1, 1949

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

By Earl L. H. Sackett

Barite, although not a glamour mineral and probably little known to many of those in the mining business, is produced in the US. in very respectable quantities and is an important factor in the mineral economy of this country. The scope of the various uses of this mineral is perhaps one of the most misunderstood things about it, for it is surprising how many of those with a casual knowledge of the subject speak of its primary utilization in terms of paint pigments and barium chemicals. The life blood of barite utilization, however, is the petroleum industry by virtue of its dependence on this high specific gravity, inert mineral as the weighting material in its drilling fluids. From 80 to 85% of barite usage in the U. S. is accounted for in this manner-in fact, its role in oil well drilling is the only excuse for some of the large-scale barite production facilities which have been developed. Other uses are important and widely varied, but comparatively they are of small scale. They include fine crushed barite of low iron content as a component in glass manufacture, barite as a source material for manufacture of barium chemicals, finely divided barite as a component of some rubbers and ground, bleached barite in pigments. The formerly substantial use of barite in lithopone, however, has declined markedly because of replacement of lithopone by titanium pigments

Jan 5, 1962