Search Documents

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By J. S. Redpath

There appears to a definite trend toward the hoisting of greater tonnages from greater depths. There is every indication that this trend will continue and we feel that improvements in the design, fabrication and installation of mine guides will be of significant importance in the future. The present state of the art in mine-shaft guide systems is reviewed and the parameters required for improvement are derived in this paper. Finally, a proposal is made for a new steel guide system which meets the parameters and is economical to fabricate and install.

Jan 1, 1977

By G. R. Mansfield

THE geologic structure of the Idaho phosphate field has an important bearing on the classifica-tion and the exploitation of the lands that contain phosphate. Maps and structure sections1 recently made available show that the phosphate is mainly preserved in downfolded or downfaulted areas. Since the phos- phate beds are generally rather soft and lie between harder and thicker formations they have been forced to adjust themselves to these formations during epochs of disturbance of the earth's crust, so that they are frequently affected by minor folds and by faults which may help exploitation by producing undue thickness at certain places or may hinder it by cutting out the phosphate at other places where according to expecta-tion it should be present. A particularly important structural feature which affects both the distribution and the exploitation of the phosphate beds is the great Bannock overthrust by which one or more slices or blocks of the earth's crust have been pushed over other blocks like ice cakes on a pond. Thus in this region a great flap of folded rocks lies across other rock structures for a distance of approximately 35 miles. Most of the commercially accessible phosphate deposits, shown in the maps that accompany the report cited, are in this flap, which con-stitutes the upper block of the overthrust. In some places, however, the phosphate in the lower block is also accessible. In both blocks post-phosphate rocks exposed at the surface here and there indicate that phos-phate beds may lie at greater or less depth below. The presence of the Bannock overthrust beneath much of the area reported is known by the occurrence of windows in the upper block both within the quadrangles mapped and in areas farther west. The portions of the lower block exposed in these windows show stratigraphic dis-cordance with the surrounding formations. The depth of the fault plane at most places, however, can be told only by drilling or actual mining. Some of the folds in the upper block are relatively deep and it seems fairly certain that the phosphate that may originally have been present in their deeper parts has been removed by thrust faulting. The estimates of phosphate reserves in folds liable to be affected by the Bannock overthrust may therefore need ultimate revision depending on the depth of this fault plane, as it may subsequently be ascertained.

Jan 1, 1928

By Frank Rieber

EVERYONE is familiar with the story of the poor Indian and his leaking tepee. He couldn't repair the leak while it was raining, naturally. And when it wasn't raining, where was the incentive? Even if this traditional Indian was apochryphal, his counterparts are certainly alive today, and operating on a world-wide scale. - A recent issue of the Wall Street Journal, for example, carried an impassioned letter from an old cocoa planter, who wants the world to know why the price of cocoa has gone skyrocketing. For years, he says, British and American interests have bought cocoa at the cheapest possible price and, incidentally, from growers willing to sell at that price. Between them, they didn't put enough money back into the business, either to fight disease in the cocoa groves or to plant new cocoa trees. Until new trees are planted and come into bearing, we will be paying exorbitant prices for our cocoa, and getting less of it.

Jan 1, 1948

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By P. Cienfuegos, J. Loredo, J. J. Fernández, F. Pendás

This coal basin is a fore-deep basin with a lot of similarities with the Appalachian basin in the U.S.A., where throughout the 1990s, the research in coalbed methane grew rapidly due to a combination of factors, including the high prices for gas and electricity. In the Asturian Central Coal Basin 129 coal beds with thickness ranging from 0.8 to 1.5 m have been recognised in the productive carboniferous in an area bigger than 1500 km2. The maturation grade of these coals varies from the external zones of the basin where the volatile content ranges from 35%-40% to 20%-30%, to the internal zones of the basin where the volatile content ranges from 20% to 10%. In this context a sustainable exploration for fossil fuel is currently being undertaken in the most favourable areas of the basin in order to evaluate the real possibilities for coalbed methane (CBM) resources.

Jan 1, 2005

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006

By Vincent Menard

The purpose of the present work is to demonstrate the removal of manganese from a neutral leach zinc-rich solution ([Zn] =150 g/L) at 80°C by oxidative precipitation using a gas mixture of sulphur dioxide (SO2) and oxygen (O2). In order to determine the optimum conditions for manganese removal, several bench-scale semi-batch experiments were performed, where the effects of ORP and gas mixing were investigated. These tests showed that SO2/O2 is a fast and effective oxidant for removing manganese down to ppm level as long as the appropriate ORP is attained/maintained and gas transfer kinetics are optimized.

Jan 1, 2006

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By George H. K. Schenck

In this decade of the 1.970's it is forecast that eight billion cubic yards of rock will be excavated from 400, 000 miles of new tunnels, drifts and other underground workings in the western world, according to estimates in a report of the Organization for Economic Cooperation and Development (OECD). It is expected that the cost of this work will be in excess of $54 billion in constant 1970 dollars. Most of this underground excavation will be in mining -- 97% of the tunnel length and 89% of the volume - -the balance in construction. In addition to this huge excavating task, in the 18 developed nations of OECD, will be projects in the Communist Bloc and in the developing nations. Underground excavation requires the successful completion of three principle activities: A. Break -- to free rock from the solid work face. B. Remove-- to clear the work area of broken rock. C. Support -- to assure stability of rock surrounding the underground excavation and to eliminate risk of rock collapse. In today's fully mechanized excavation systems, continuous miners, roadheaders or tunnel borers, (A) break the rock loose from the face, and (B) remove broken rock with their mucking devices and load it onto belt conveyors, mine cars, trucks, or any other appropriate haulage system for disposal. Such operations contrast to the more complex, intermittent systems employed when

Jan 1, 1974

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

Develop a mobile manipulator that one person can use to lift and maneuver 50- to 600-pound loads. It can be used in maintenance shops and mines to reduce lifting accidents (Figure 1 and 2). Background Lifting heavy items is one of the leading causes of injury in the workplace. Mine Safety and Health Administration statistics showed that, in 2004, back injuries accounted for over 20% of all injuries (1,699 cases) and resulted in 110,000 lost days of work. Forty-one percent of those injuries resulted from materials-handling or maintenance activities.1 In addition to back injuries, lifting injuries include hernias, ruptures, sprains, and strains resulting from losing control of the item being lifted. Factors associated with accidents are weight of the item being lifted, awkward postures, inadequate handholds, and the working environment itself. High accident rates were noted when lifting items that ranged from 50 to 600 pounds, particularly in tight working quarters where maneuverability was critical. Research indicated that a mobile lifting arm would eliminate many lifting accidents in environments where other lifting devices (fork lifts, overhead cranes, mobile A-frames) would not be practical. NIOSH has built a first-generation mobile manipulator unit designed to be used on hard, level floors such as in a shop. The complexity of motion, number of moving parts, compact design, and design constraints of the manipulator required advanced computer-aided design work (Figure 3). As a result of the design work, thirty-eight claims are included in the patent applications. NIOSH will be conducting field trails and working with manufacturers to put the manipulator into industrial use.

Dec 1, 2006

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By L. D. Schmidt

Now that the war is over, there is a great revival in popular demand to decrease pollution of the atmosphere in our cities. Great cities, such as Pittsburgh, are starting to enforce laws against violators of smoke ordinances. The substitution of low-temperature coke for bituminous coal in household heating is a most promising field for helping to eliminate the smoke nuisance. This Information Circular is written to assist in the very worth-while effort to reduce atmospheric pollution. Herein are de- scribed recent German developments in the production of low-temperature coke. Operating and cost data are given on German commercial-scale low- temperature carbonization plants.

Feb 1, 1947