Search Documents

By S. Gallagher, A. G. Mayton

Back injuries account for a high proportion of lost workdays in the mining industry and are a leading cause of disability in mine workers. Two risk factors for low back injuries are manual lifting and whole-body vibration exposure when operating mobile equipment. Recent research has shed light on possible mechanisms through which low back injuries may occur, and the results of these studies can be used to improve the design of lifting tasks and seats to decrease injury risk. This article discusses recent research results and how this knowledge can be leveraged to reduce the risk of low back pain.

In most surface mining operations, overall project economics is driven to a significant extent by the slope angles that can be achieved within the rock masses present. This is particularly true of precious metal pits in which stripping ratios can be relatively high, although examples from other non-precious metal operations (such as large iron ore and copper pits) can also be found. As a consequence, it is not surprising that in most large (deep) open pit mines, relatively small changes in slope angle (of the order of two or three degrees can translate into changes in project value measured in the tens or even hundreds of millions of dollars. Understanding how this potential value can be realised, and quantifying the associated risks, should be one of the key outcomes of modern slope engineering practice. In striving for optimised slope angles, therefore, mining companies and their specialist consultants are increasingly turning to more sophisticated methods of engineering open pit walls. This paper summarises contemporary slope engineering practice as well as some of the key technical issues that are either currently being researched or will need to be researched in the future. It is written in the context of the slope engineering process; namely, data collection and analysis, failure mode identification and stability assessment, slope design, slope formation, and slope (face) mapping and monitoring (the latter two activities being the primary on-going data collection functions that close the design loop).

Jan 1, 2002

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

By M. Rezaee

Push backs used in the production planning of open pit mines play an integral role in generating annual cash flow. Although several algorithms for push back designs have been proposed, none have studied the optimum number of push backs. In this paper, different algorithms have been implemented for the push back design of a cross section of a copper deposit and the results discussed. Moreover, the optimum number of push backs has been determined using analytical and multiple attribute decision making (MADM) methods based on minimizing the risk associated with grade uncertainty, and minimizing stripping ratio, while maximizing net present value (NPV). According to the findings, the optimum number of push backs has been proposed to be between three and six, as lower quantities of push backs are more likely to achieve the calculated net present value, and have smoother stripping ratios for different pushbacks. This approach was examined in an operating mine and the optimum number of push backs determined to be four.

Jan 1, 2012

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By Yijun Caoa, Xiuxiang Taoc, Zhongbo Hub, Yinfei Liaoa

A new preparation scheme for a difficult-to-float coking coal from the Kailuan Mine, Tangshan, China was investigated. The results showed that grinding followed by column flotation was beneficial for obtaining products with low ash content. The positive effect of grinding on the coal floatability is attributed to the liberation of intergrowths and coal surface improvement. Tests indicated that 10 minutes was the optimum grinding time, and over grinding resulted in a deterioration in flotation performance. With a grinding time of 10 minutes, conventional flotation had potential to yield a product with around 12.42% ash content and 69.15% combustible recovery. Column flotation can reduce the product ash content to 11.15%and increase combustible recovery to 74.47%. Consistently better flotation results reveal that column flotation is more efficient than conventional flotation for such fines.

Jan 1, 2015

By Tetsuo Yamazaki

Metal market prices rose drastically in 2006, and most broke historical records as shown in Figs. 1-4. This increase has been basically driven by economic growth in Asian countries, especially China. The growth trend is expected to continue for several years. Then, India will follow the same growth trend. Their metal demands keep the price levels high for 20 years or more. One more additional important factor on the metal market prices is hedge funds come into the market. Japan imports all metals for domestic use from overseas. The amounts imported were 1.27 million tons in copper, 0.32 million tons in lead, 0.59 million tons in zinc, 0.20 million tons in nickel, and 1.18 million tons in manganese, respectively in 2006 (Source: http://www.jogmec.go.jp/j_resourse/index.html#03). Though mainly we import the concentrates and our domestic customer smelters take the part of metallurgical leaching, the payment necessary for purchasing the concentrates is estimated about US$ 10 billions in 2006. The payments in 2005 and in 2003 were about a half and a quarter of the 2006, respectively. Japan must have effective counter measures to reduce the future payments.

Sep 24, 2006

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By D M. Hunter, S M. Iveson, K P. Galvin

For low density materials such as coal, density-based fractionation of particles via the sink-float method is relatively simple due to the availability of liquids of suitable density; however, for high density minerals, suitable heavy liquids are less available and those that are available are expensive and pose significant hazards. At best, sink-float separation can be performed up to densities of 4400 kg/m3 with the use of Clerici’s solution at elevated temperatures. Hence the direct measurement of grade-recovery and density-partition curves is problematic. Therefore, in most cases, beneficiation plants must rely on methods such as QEMSCAN, density tracer particles or very limited information to guide them in the design and optimisation of their plants.This paper describes a density-fractionation method utilising laminar flow through a system of parallel inclined channels to generate a series of overflow fractions at different flow velocities. Here the particles are subject to precise hydrodynamic forces with minimal dispersion or mixing. The size distribution of each overflow fraction at a given flow velocity is obtained using a laser particle size analyser, and combined with a laminar flow model to deduce the corresponding density distribution. The paper describes the application of the method to measure the separation achieved using a REFLUX Classifier to obtain the corresponding feed, product and reject ‘washability curves’, and in turn the full partition surface. Approaches used to corroborate the findings are discussed.CITATION:Hunter, D M, Iveson, S M and Galvin, K P, 2017. A batch elutriation technique for the density-based fractionation of iron ore, in Proceedings Iron Ore 2017, pp 195–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By Glenn K. Nolan

"Today, more than any other time in recent history, aboriginal communities are looking for ways to be understood as more resource development companies continue to explore and develop Canada's vast resource potential.Recent Supreme Court rulings have affirmed the need to engage aboriginal communities early on in resource development projects. There are many conflicting ideas on how, who, and when to engage. Given the large number of communities and varied cultures, each resource development company must equip itself with a better understanding of the people they are planning to work with.The lecture will begin with a basic historical perspective on treaties and the various societies across Canada. We will also explore the current situation many communities find themselves in today. Building a meaningful relationship with a community is the foundation for a lasting partnership. Every community is unique and every approach to engage communities must be just as unique. The lecture will outline some basic steps that can lead to a better relationship building process between the communities and companies."

Jan 1, 2008

By Shaun Booth

Automating Delay Reporting to Deliver Effective Maintenance Corporate Background: Technology Company: Matrikon Inc. Global software and service provider of Information Technology and Control Solutions that deliver Business Results. Case Study Facility: Bulga Coal Handling and Preparation Plant <CHPP> Australian site, part of Xstrata, an international Swiss natural resources group. Technology: ProcessMORe ? Missed Opportunity Reporting (Delay Reporting). Matrikon?s technology implemented at many facilities, to deliver effective maintenance Matrikon International Inc. Global software and service provider of Industrial Decision Support, maintenance and control solutions, with universal connectivity to existing systems and work processes. ? 1999 ? 100 employees ? 2003 ? 450 employees ? Our offices: 20 offices worldwide: ? Quebec, Toronto, Edmonton, Calgary, Ft.McMurray, Vancouver ? U.S. ? Australia (formerly Hunter Controls)

May 1, 2003

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

By E. J. Matson

"The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties.A preliminary examination of the Mount Hope mine was made in January 1943 by the Bureau's engineers, who recommended exploration by diamond drilling.The mine is in the unsurveyed portion of T. 22 N., R. 1 E., Mount Diablo base and meridian, south-central Eureka County, Nevada, 25 miles by road north of the village of Eureka. A partly graded and Graveled secondary road connects the mine and Eureka on U. S. Highway 50.Extensive sampling was done by the Bureau in February. 1943. Core drilling from the surface was started on March 15, 1944, and completed on April 2, 1545. The 16 holes drilled totaled 7,215 feet. The mining company also did extensive underground core drilling from April 21, 1944, to January 4, 1945. This report gives the results of core drilling supervised by the Bureau of Mines.The drilling program was designed to explore for extensions of the mineralization exposed in the mine workings. As a result of drilling, additional ore was found, and it is believed that this project has fulfilled the purpose for which it was planned.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization, of our mineral resources to the end that they make the greatest possible contribution to na¬tional security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation test. Both these branches are under the supervision of Dr. R. S. Dean, assists director.With respect to this report special acknowledgment is due to Charles W. Merriam of the United States Geological Survey for his interpretation of the Mount Hope mine Geology and his cooperation throughout the project; Col. Leverett Davis, former lessee of the property; K. K. Hood, manager of the Mount Hope Unit, Callahan Zinc-Lead Co., Inc.; C. P. Knaebel, assistant manager, and M. P. Nackowski, geologist, of that company, for their help, and to the Sullivan Machinery Co. for its assistance."

Aug 1, 1946

By Tatiane Haskel

A utilização de ligas Al-Si tem se expandido industrialmente principalmente no setor automobilístico. Cabeçotes, blocos de motor, rodas entre outros são exemplos de componentes produzidos com essas ligas. Estes componentes normalmente estão sujeitos a carregamento cíclico. O objetivo desse trabalho foi estudar o comportamento da liga A356 utilizando corpos de provas submetidos à fadiga por flexão rotativa nas condições brutas de fundição e tratadas termicamente por T6. Corpos de prova para ensaios de tração e de fadiga foram obtidos por fundição por gravidade em coquilhas. A comparação dos resultados foi realizada com os resultados do limite de resistência, do limite de escoamento, do alongamento e das curvas S-N. Adicionalmente análises fractográficas foram realizadas para verificar o comportamento de fratura. A liga tratada termicamente apresentou melhores resultados no ensaio de tração e de fadiga na faixa de 103&lt;N&lt;107.

Aug 16, 2017

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.