Search Documents

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

Recent Bureau of Mines research in earth grounding safety is documented in three separate papers. First, guidelines for the design of a 5- ohm borehole ground are presented. Next, an inexpensive practical means to construct a low-resistance bed in high-resistivity soil is described. Finally, a procedure that employs a commercial resistivity meter to measure shock potentials around grounded objects is explained step-by-step. These papers complement the material presented at an earlier technology transfer seminar and published as IC 8767.

Jan 1, 1985

By Osmar Roberto Bagnato

Este trabalho apresenta um estudo do desgaste de insertos e tensões residuais em diferentes estratégias de entrada de ferramenta no fresamento da liga Ti-6Al-4V. Esta liga possui propriedades mecânicas que a torna ideal para aplicações onde é necessária uma ótima relação resistência-peso. O objetivo é reduzir o desgaste dos insertos no processo de fresamento e analisar as tensões residuais na usinagem da liga Ti-6Al-4V. A integridade superficial do material após a usinagem deve ser conhecida já que esta liga é utilizada em aplicações criticas. Quatro estratégias de entrada foram estudadas, sendo que no faceamento foi utilizada a entrada por rolagem e a frontal reta e no fresamento de cavidade foi utilizado mergulho reto e em rampa. Em todos os ensaios foram utilizados os mesmos parâmetros de usinagem. As tensões residuais foram medidas por difração de raios-X (Luz Sincrotron), pelo método sin²?, utilizando um difratômetro de raios-X instalado no LNLS. No faceamento a estratégia por rolagem mostrou uma importante redução do desgaste e uma pequena redução da tensão residual quando comparada com a estratégia frontal reta. No fresamento de cavidades a estratégia de mergulho reto mostrou um inesperado aumento do desgaste e uma significativa redução da tensão residual quando comparada com o mergulho em rampa. Todas as tensões residuais encontradas foram compressivas. As tensões residuais encontradas em todos os experimentos se mostraram favoráveis a aplicações sujeitas à fadiga.

Aug 8, 2018

By H Matsuno, N Oyama, T Yamamoto, K Nakajima, Y Iwami, N Saito

Recently, the quality of sinter feed ore used in sintering process has deteriorated. In particular, Fe has decreased and gangue component has increased in the sinter feed ore. Increase of gangue is not only the factor to influence sinter qualities, but also the factor to increase coke ratio in the blast furnace operation as the increase of slag ratio. Therefore, to cope with the deterioration of iron ore qualities, studies on alternative iron ore resources and development of its utilisation technology have been required.In that kind of new iron ore resources, authors focus on high-grade magnetite fine. High-grade magnetite fine decreases sinter productivity by the decrease of permeability of sintering bed. Therefore a new study for using large amount of magnetite fine is required. In the past, there are some studies about the effect of mixing ratio and size of magnetite fine on productivity and quality, but there are few studies about magnetite fine segregation in charging.In this research, the melting behaviour and interfacial reaction calcium-ferrite, which has important role as bonding agent among iron ores, melts into hematite substrate and magnetite substrate was studied. As the results, it was defined that upper segregation of high-grade magnetite fine is suitable for productivity of sintered ore. Based on this knowledge, the control method of high-grade magnetite fine segregation by magnetic force at charging was studied with DEM (discrete element method) and its verification experiments for magnetic segregation control was conducted in the laboratory.CITATION:Iwami, Y, Yamamoto, T, Oyama, N, Matsuno, H, Saito, N and Nakajima, K, 2017. Improvement of sinter productivity by control of magnetite ore segregation in sintering bed, in Proceedings Iron Ore 2017, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Newell G. Alford

COAL companies are definitely becoming conscious of the need for better organization. Mechanized mining and the intricate preparation of coal have brought with them the demand for better trained and more highly skilled mining personnel. Refinement in coal mine management is increasing the demand for young graduate engineers to start in the lower grades of the reorganization and prepare themselves to meet rapidly increasing coal mining responsibilities. The interest is wide in scope and extends from self-helps, extension work, and management study at the mines to stimulation of interest in coal mining amongst undergraduate mining students, leading to their permanent employment after graduation. Data by the United States Bureau of Mines show the total annual value of coal production (bituminous and anthracite in the U.S.) through the past 22 years as being more than 38 per cent of the combined value of all ocher mineral industry products. Natural-gas production has gained rapidly on coal since 1916; petroleum exceeded coal beginning with 1934 (see Figure 1). For this 22-year period, the Committee on Student Interest in Coal Mining, in the A.I.M.E., made a survey of the mining schools in Canada and the United States to show the approximate absorption of young graduate mining engineers by the coal industry. In 1938, 232 mining engineers were graduated as compared with 42 in 1918 (a war year) and 180 in 1923. From 1923 to 1929 the graduates declined to another low of 90, but from there on there was a rapid annual increase in the graduating output, reaching a total of 232 in 1938 and continuing upward to a maximum of over 325 graduating this present month.

Jan 1, 1940

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

The small scale alluvial gold mining industry in Papua New Guinea (PNG) is c.irrently the only form of small scale mining carried out in this country. It already contributes significantly to the economy with current production estimated at 2 000-2 500kg per year. Until recently, small scale alluvial gold mining has been confined to simple panning and sluicing of high grade alluvial and colluvial deposits. Traditionally the small scale miner in PNG has only worked gravels with gold grades in excess of 500mg/m3. Grades of this order are required to justify the hard physical labour involved ~n hand operated small scale mining methods. .he introduction of higher throughput technologies such as trommels fed by hydraulic excavators has the effect of altering what constitutes an economically viable deposit. Mechanised techniques allow for the consideration of grades of almost half that level. The potential and opportunities for utilising this type of small scale mechanised mining in PNG are enormous with large areas of ground with gold grades running in excess of 250mg/m3 and often up to 2000mg/m3 throughout the country. An assessment of the current operating economics of this technology in the PNG context is the principal objective of this paper. Small to medium scale mechanised mining can potentially contribute significantly to the PNG economy particularly as it lies within the react-, of many PNG businessmen. Its potential is currently somewhat limited by a general lack of infrastructure and is also constrained by socio-political factors.

Jan 1, 1991

By Terri Jordan, Gregory Hempen, Thomas Keevin

Water-borne blast pressures from confined blasts were recorded as part of a submerged blasting program in Florida for channel deepening. The blasting was confined within the rock floor by stemming. Shot patterns of stemmed borings were recorded, as were two open-water shots. One hole of one shot was not confined properly, which allowed comparison of confined and a poorly confined larger charge weights per delay. The pressure data were intended to gain information on typical pressure measures from the rock removal program relative to impacts on marine organisms. Water-borne pressures from actual confined, rock-removal shots validate the hypothesis of lessened impacts to aquatic and marine biota.

Jan 1, 2007

By V. O. Murray

Gentlemen: I'm glad to see the crowd that's here this morning, glad to renew acquaintances with many old friends, and if you'll look at the program you'll see a heading there which states that as President I have the honor and pleasure to be here to address the membership of this meeting of the Rocky Mountain Coal Mining Institute, this being the 49th regular meeting. The tentative schedule of this gathering lists on the program the "President's Address," and I want to assure you that this will not be an address or a lengthy speech. It's said that a good speaker is one who arises to the occasion and then promptly sits clown, so please be at ease for I intend to sit clown very soon. There are other men here who have spent time writing and preparing papers on subjects that are to come up for discussion at this meeting, which will be, I'm sure, more interesting than what I have to say this morning; so again I'll say, we'll get this part of the program under way promptly.

Jan 1, 1953

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By Turner WG, Short RR

Obviously, the paramount advantages of contract mining have been recognised by mine developers throughout Australia, as evidenced by surface gold mining operations of significant output almost exclusively being performed under contract. These paramount advantages of using an experienced professionally managed contractor result from the mine developer being freed from financing the required relatively large capital expenditure at current relatively high interest rates or in a capital scarce stock market, and from the need to recruit and sustain a large operating work force in a competitive labour market.

Jan 1, 1990

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management."

Jan 1, 2003

By S. J. Duda

Procedures for detecting and locating seismic sources are adapted to the case of entrapped miners. During an emergency the entrapped miner is likely to generate seismic signals, by knocking against the walls of the shaft. With a seismic array station deployed near the disaster area, the seismic signals can be recorded. Two algorithms are presented for the location of the source from the arrival times of a seismic phase: The first algorithm produces one, most probable location, under the assumption of constant velocity of propagation of seismic waves in the medium. The second algorithm is similarly applicable, however without any restriction on the seismic velocities in the medium between the source and the array. While the first algorithm uses an analytic approach, the second one is based on a trial and error procedure. The second algorithm gives locations with arbitrarily high accuracies, depending only on the accuracy of arrival time measurements and on the compatibility of the true velocity distribution and the assumed velocity model. The algorithm is shown not to require under certain conditions direct .arrival time measurements, thus eliminating a potential source of errors in the location of entrapped miner.

Jan 1, 1973

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

Coal, America's most abundant fossil fuel, is expected to play a key role in our pursuit of energy independence. A substantial increase in coal exploitation will be required if we are to fulfill our future energy needs. It is essential that new developments continue if stable coal prices are to be achieved and maintained. The challenge of the mining industry is to continue these developments in the face of problems related to increasing labor costs, inflation and environmental restoration. With expectations of increased activity in surface coal mining, the U.S. Bureau of Mines has authorized this study to determine the preliminary economic and technologic feasibility of underspoil haulage in area strip coal mines and to identify geologic and geographic areas where such a system could be used. These objectives were met by literature search, data-gathering visits to several active area strip mines and by analyzing various haulage systems that were superimposed on three model mines. Potential advantages of such a system include: 1) improved mine design; 2) lower mine operating costs; 3) improved land reclamation; 4) lower manpower requirements; 5) lower mobile equipment requirements; and 6) smaller, less sophisticated maintenance facilities.

Jan 1, 1975