Search Documents

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

By M. C. Irani

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By M Vendrup, T C. Christensen, C Dube

The adsorptive and granulate forming MetClean™ process has been used at many locations in Northern Sweden, Norway, Denmark, France, Spain, Mongolia, Japan and Australia. It has been pilot tested and used in full scale treatment plants to remove metals from:mine watersleachate from solid waste in incineration flue gasleachate from fly ash damsleachate from landfill and waste ponds.The following paper provides details of pilot and plants tests on the effectiveness of MetClean™ in removing arsenic, antimony, barium, cadmium, copper, molybdenum, nickel, radium, uranium, vanadium and zinc. Results show that MetClean™ may reduce the concentration of these metals in treated effluent water to the one part per billion (ppb) range.The paper also finds that, for specific metals, the optimal adsorption condition depends on the:pH levelmolar relation between the specific targeted metal and the addition of iron (II) or manganese (II)type of oxidation agentssalinity levelpresence of other metals.The most effective pH level varies according to the targeted metal but falls within the pH 5 to pH 11 range. A compromise pH level may be set when more than one metal is targeted for removal at the same time and through only one process step. The removal efficiency of one or both metals may be affected by operating at a compromise rather than optimum pH level.The MetClean process generates non-hazardous solid waste. Waste can then be disposed of more easily than brine or sludge.CITATION:Christensen, T C, Vendrup, M and Dube, C, 2015. Pilot tests for heavy metals removal in mine water, in Proceedings MetPlant 2015, pp 404–415 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By A. Adu-Acheampong

Stope instability at Ashanti Goldfields Company Ltd. (AGC) is a major concern. Using information from field mapping, major discontinuity sets were defined, Rock Quality Designation (RQD) was determined. The stability of wedges in the stope walls was assessed using the commercially available computer program UNWEDGE(Rock Science, 1992). Analytical results indicate that the presence of graphite infilling in joints contributes to instability, while steeply dipping joints control wedge slabbing and wedge toppling in the hanging wall. Stable stope widths and dimensions were determined to range from8.1 to 30 meters (m).

Jan 1, 2003

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recept studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d18O values. Preliminary oxygen and carbon isotopic data for some important gold deposits of eastern Australia have emphasized the diverse origins of their ore fluids.The Mount Morgan gold-copper orebody is shown to be of the volcanogenic massive sulphide type with ore fluids predominantly of sea water origin. The Charters Towers fissure veins formed during hydrothermal activity associated with intrusion of Lolworth Igneous Complex equivalents. Oxygen isotopic studies of the quartz reefs at Stawell and Gympie have been inconclusive. The ore fluids have a d18O value of about 7 per mil and may be of magmatic or metamorphic derivation.

Jan 1, 1981

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

During the modeling of grinding systems, population balance modeling (PBM) which considers a constant breakage rate has been widely used over the past years. However, in some cases, PBM exhibited some limitations, and time-dependent approaches have been developed. Recently, a non-linear framework which considers the traditional linear theory of the PBM as a partial case was introduced, thus allowing the estimation of product particle size distribution in relation to grinding time or the specific energy input to the mill. In the proposed model the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (RR) distribution. Besides, the adaptability and reliability of the prediction model are among others dependent upon the operating conditions of the mill and the adjustment of the RR distribution to the experimental data. In this study, a series of grinding tests were performed using marble as test material, and the adaptability of the non-linear model was investigated using three loads of single size media, i.e., 40, 25.4, and 12.7 mm. The results indicate that the proposed model enables a more accurate analysis of grinding, compared to PBM, for different operating conditions.

Jun 24, 2023

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By R. A. Bosch, F. V. Lenel, G. S. Ansell

RECENTLY, Ansell and aenel' proposed a dislocation model to account for the yielding behavior of dispersion-strengthened alloys. The criterion for yielding used in this model was that yielding occurs when the shear stress due to arrays of piled-up dislocations fractures or plastically deforms the dispersed second-phase particles. Calculations based on this model predict that the yield strength, uysof a dispersion-strengthened alloy containing particles whose geometry permits them to be considered as straight, i.e. not curved, barriers to dislocations follows the relation where and are the shear moduli of the matrix and dispersed phase respectively, b is the Burger vector of a dislocation in the matrix, A is the mean free path between dispersed phase particles and C is a constant. This yield stress, ys, is closely approximated in polycrystalline alloys by the proportional limit. The offset yield stress, uoy, is the yield stress, uys, plus the increase of stress due to strain hardening in the offset strain increment. Previous investigation1 has shown that Eq. [I] describes the yielding behavior of several different dispersion-strengthened alloys as a function of the mean free path between dispersed phase particles at a constant temperature. The purpose of this investigation was to investigate the temperature dependence of the yielding behavior of dispersion-strengthened alloys. The alloys studied, MD2100 and MD5100, are SAP-type alloys containing flake shaped aluminum oxide particles dispersed in a matrix of commercial purity aluminum. The proportional limit and 0.2 pct offset stress of both of these alloys were determined as a function of temperature over the temperature range from -190" to 500 C. All tests were conducted on an Instron tensile testing machine. Stress was measured by means of the Instron load cell. Strain was measured by means of SR-4 strain gages attached to the tensile specimens. Stress sensitivity was 80 psi. Strain sensitivity was 2 x 10F Fig. 1 shows the values received for the proportional limit and 0.2 pct offset yield stress plotted as a function of homologous temperature for both the MD2100 and MD5100 alloys. Inspection of Eq. [I] shows that of the terms which determine the theoretically predicted yield stress, uy,, only the shear moduli have an appreciable temperature dependence. From Eq. [I] the yield stress at any temperature T, UT, may be predicted from the yield stress at any arbitrary reference temperature, in this case 25 OC, u25, by the relation where the subscripts T and 25 refer to the values of the property at test temperature and at 25"C, respectively. The temperature dependence of the yield stress predicted by Eq. 121, based on the observed value for the proportional limit at 25OC, is also shown in Fig. 1. In evaluating Eq. [2] the following data was used. The values for the shear modulus of

Jan 1, 1962

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

By S. K. Shaha, A. Gryguc, S. B. Behravesh, B. Williams, M. Wells, H. Jahed

Warm forging to near final product geometry shows promising benefits in terms of microstructure refinement and texture modification. In the present study, Semi-closed die forging was performed on extruded AZ80 magnesium alloy at a forging temperature of 400 °C and various forging ram speeds. Compression tests were performed to investigate the influence of forging at various deformation rates on the performance of extruded AZ80 magnesium alloy. The microstructural analysis showed that the extruded AZ80 possesses a grain structure typical in wrought magnesium alloys, with sharp basal texture. In contrast, the forged samples had a recrystallized microstructures and a spatially varying textures and crystal orientations resulting from the complex flow behaviour within the closed die forging. Furthermore, once forged, a significant increase in the material isotropy, homogeneity as well as failure elongation were observed. An increase in UCS of 9% was observed in the forging direction, while the UCS in the extrusion direction was similar to that before forging. The changes in UCS can be attributed to both the refined grain microstructure and crystal reorientation. Successful microstructure recrystallization occurs for strain rates which traverse several orders of magnitude, and in general, UCS isotropy increases with increasing strain rate. It is believed that forging cause’s grain refinement and texture modification which act to enhance the mechanical performance (UCS, fracture strain and superficial hardness) for the forging conditions investigated in this study.

Mar 1, 2017

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By D. Mark Richards

Highland Valley Copper (HVC) is a large open pit copper mine in the southern interior of British Columbia. Machine guidance technology using GPS has been utilized at the mine since 1996 for blast hole drill navigation and since 2000 for shovel and dozer navigation. Since 1997, rock recognition has been part of the drilling process. This allowed the mine to develop a Mine to Mill strategy using the rock hardness information from drill monitoring systems to both refine drilling and blasting parameters as well as downstream crushing and grinding strategies. Although this preliminary effort has been very successful at HVC, the current intent is to gain further benefits through better use of existing information while also deriving an enhanced data set from monitoring production drills. In the latter case, the objective is to acquire and process drill variables in such a manner as to permit more detailed definition of rock mass characteristics. The subsequent focus will be to use the derived geotechnical and geological information as part of a practical process to more prescriptively blast the rock mass. Through the definition of domains based on drill monitored derived rock mass properties, the intent will be to enhance blast outcomes that lead to optimized downstream (from blasting through to concentration) processes in a more proactive and timely manner. This paper examines a proposed approach to be able to derive more accurate and consistent rock mass properties from production drilling. In addition, the discussion will identify potential benefits to be gained from process improvements that result in enhanced productivities, and crushing and grinding optimisation due to blasting strategies that are more closely matched to identify rock mass characteristics.

May 1, 2007

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008