Search Documents

Introduction Some people say it is almost impossible to get mining permits in California. Some say the day of the lone mining entrepreneur is past. And some say you cannot make money mining gold where old-timers have already mined it, especially in Tertiary gravels. But a young mining operator and SME member, Tim Callaway, is proving these ideas wrong. Callaway's company, Brush Creek Mining and Development Inc., has the necessary permits for its Gardner's Point gold mine in Sierra County, CA. And, Callaway has secured funds for the 7.7 km'/d (10,000 cypd) Tertiary gravel operation. The company's initial goal is to produce 373 to 466 kg/a (12,000 to 15,000 oz per year) of gold at Gardner's Point mine at a cost of less than $6.43/g ($200 per oz). Feasibility studies are currently being conducted to consider product levels up to the 1555 kg/a (50,000 oz per year) involving additional plants and infrastructure. While exploring for other hard-rock properties, the Brush Creek company already operates the Brush Creek lode gold mine. The mine sits high on a ridge south of Goodyear's Bar, which is located on the North Yuba river. It might be noted that the Brush Creek mine has been the subject of media stories recounting how a mine can operate with sensitivity to the environment. Gardner's Point project In 1983, Callaway negotiated with the Gardners Point Ltd. Partnership for control of the Gardner's Point property. The Partnership had been engaged for three years in securing permits, mapping and drilling, and test mining. The Partnership actually mined about 43.5 dam3 (57,000 cu yd) of gravel, which yielded 25.2 kg (810 oz) of free gold. Later, the Brush Creek company acquired ownership of the property. The company then began its own exploration and development program. As underground development proceeded at the Brush Creek mine, plans matured for a high-volume operation at Gardner's Point. Australian and English investors contacted Callaway. A joint venture was negotiated. The Australian owners became majority participants; the Brush Creek company, a minority participant and the operator. The Australian investors agreed to contribute $3.5 million (60%) to the Brush Creek Joint Ventures. The Brush Creek company will contribute its expertise as well as assets and liabilities valued at $2.3 million (40%). About $2 million has been allocated to the Gardner's Point project. Later, Brush Creek Mining and Development Inc. sold 50.4% of the company's common stock to English investors for $5.4 million. Callaway negotiated this private placement, which permits further exploration of projects being investigated. Geography and history The Gardner's Point mine is located in the northern Sierra Nevada of California, about 9.6 km (6 miles) east of the little town of La Porte in Plumas County. The mine lies high on a ridge above Slate Creek, which divides Plumas and Sierra Counties. La Porte is accessible from the Sacramento area by a winding, paved, two-lane highway. But the mine is reached only by two different unpaved county and Forest Service roads. Both roads include steep grades in and out of the Slate Creek canyon. Mine elevation is about 1.4 km (4600 ft) above sea level. The area is thus threatened by occasional heavy winter snows, though it

Jan 3, 1987

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

"8.1. IntroductionThe stoichiometry of most named platinum-group minerals (POM) is known (cf. Cabri, 1981b, in Chapter 7), but, because these minerals are subject to a wide range of element substitutions, representative analyses require treatment in a separate chapter (section 8.2). The analyses, in all cases done by electron microprobe, are grouped in sections according to the principal platinum-group element (POE) for each POM, and then follow sequentially with increasing amounts of the principal POE starting with the ideal composition, when known. In order to facilitate reference to specific POM by name, an alphabetical listing is also given (Table 8.1). A range of compositions, in addition to one or several ""representative"" analyses, is given for some POM when more than one analysis has been reported for a particular locality. The tables of POM analyses (Tables 8.2 to 8. 76) include at least one analysis for every locality for which data have been published, to the best of the authors' knowledge. All analyses are referenced for locality and publication source, and include several unpublished analyses (all but one done at CANMET). Most analyses have been rounded off to one decimal place for amounts more than one per cent and their formulae calculated on the basis of an even number of total atoms. In all tables, ''n.d.'' stands for elements sought for but not detected and a dash signifies elements not sought, or when these haven't been specificed in the publication source.Section 8.3 contains tabulated analyses and, in some cases, also includes a critical assessment of POE-bearing minerals in which the POE occur in trace or minor quantities. The organization of the data in this section is by mineral groups; e.g., sulphides, sulpharsenides, silicates, etc. Some of these data are also discussed in Chapter 4 by Crocket (1981) and are discussed briefly in Chapter 6 by Crocket and Cabri (1981)."

Jan 1, 1979

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By J. H. Adkins

The purpose of this research is to identify hazards associated with roof bolting and to make recommendations for procedural and equipment design changes to reduce those hazards. To that end, the project reviewed Literature on related research, collected and analyzed roof bolting injury data, normalized the injury data be exposure time to each activity and identified problem areas within the root bolting tasks. In addition, field data collection forms were prepared and mines selected for field work. In the field, observations were made of eighty (80) different roof bolting crews bolting one hundred fifty-five (155) place;, on forty (40) sections spread among nine (9) mines. Task analysis forms were used to record unsafe behavior or conditions for each crew and each place. Informal discussions were held with the mine's safety and training officer, the maintenance officer, one section foremen and, when possible, the observed crew, concerning the training and experience of the miners. Unsafe acts were categorized and related to the "Activity While Injured" categories developed during the accident analysis. For each of these categories one or more recommendations for corrective measure, machine modification, procedural change or job training were developed. The study produced over fifty (50) specific recommendations involving machine design, procedural, safety training and supervisional issues that would lead to reduced roof bolter injuries in the near term. The authors concluded, however, that only the development of truly hands off/remote bolting can eliminate or reduce to an absolute minimum the hazards to which the roof bolter is subjected.

Jan 1, 1977

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By E. M. Norris

Phosphate deposits are distributed widely over the earth's surface. Of the known areas of deposit, eight fields are of particular interest because of their vast reserves of high grade phosphatic material and the volume of their production that goes to the world's great consuming areas. These fields, in the order of their present economic importance, are situated respectively in Florida, French Morocco, Kola Peninsula of U.S.S.R., Tunisia and Algeria, Tennessee, Montana-Idaho-Wyoming-Utah, Ocean and Naru Islands in the Gilbert group, and in Egypt. The Rocky Mountain deposits have a comparatively low ranking in the phosphate trade of today, but this field contains one of the largest known reserves of phosphatic material, associated with which are recoverable trace minerals, which are of increasing importance in our national economy. The first discoveries of phosphate rock in the western states were recorded in Cache1 and Rich2 counties in Utah, respectively in 1889 and 1897. Mining operations were begun on these deposits near Montpelier, Idaho, in 1906. During the latter year geological studies of the phosphate beds were started by Weeks and Ferrier of the U. S. Geological Survey. These studies have been continued to the present day by a distinguished roster of the Survey's technicians. As a result of this systematic exploratory program, the Survey has published a series of bulletins, papers, and maps, which provide the mining public with a comprehensive study of the exposed

Jan 1, 1949

The wealth of a nation can be measured many ways, but one of the most important measures is its natural resources, particularly minerals. Minerals provide the foundation upon which economic prosperity and defense preparedness rest. Assessing our energy and mineral resources and assuring their development is in the best interests of all our people continues to be an important national goal. Since its founding in 1910, the U.S. Bureau of Mines has established itself as the world's premier minerals information and research agency. Its authoritative, comprehensive data and pioneering research have contributed significantly to a strong U.S. mineral position in the world.

Jan 1, 1990

By Sam Tour

WHAT is a die-casting and what is the die-casting industry? From the literal translation of the words "die" and "casting"' one concludes that a die-casting is a casting made in a die. The casting may be of any metal or alloy or, for that matter, may be of some nonmetallic material capable of being cast, such as plaster of paris or glass. The die may be of any material that will take successive casts so it need not necessarily be metallic in nature. The term "die-casting," therefore, is indeed broad, though in practical usage it has come to mean the casting of metals and their alloys in metallic molds or dies. Even this limitation of the term leaves -a broad field, for castings may be made in a number of different ways. For example, the molten metal may be allowed to run into the die by gravity it may be sucked into the cavity of the die, it may be forced to take the contour of the cavity in the die by centrifiugal force, or it may be forced into the cavity under hydrostatic pressure. In England, castings made by practically all of these

Jan 1, 1935

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By D. R. Tweeton

The U.S. Bureau of Mines has developed tomographic computer programs for geophysical applications and is distributing them as part of a Bureau plan to facilitate the transfer of technology to potential users. These programs were developed for predicting and monitoring the flow pattern of leach solution during in situ mining. The Bureau has also applied them to assessing high-wall blast damage and examining the integrity of mine-related geological structures. This report describes the curved ray program BOMCMTR (Bureau of Mines curved ray tomographic reconstruction), tells how to run it, and gives examples with synthetic and field data. BOMCRATR provides optional mathematical constraints to counteract the nonuniqueness of tomographic reconstructions with crosshole data. These constraints include limiting the maximum and minimum velocities, fixing the velocity at any point to any value, and establishing layers in which velocity does not vary with horizontal position. The user can test for nonuniqueness by varying the initial velocity pattern, The program can perform either curved or straight ray analysis. Ray paths are calculated analytically in triangular pixels, which is faster than incremental numerical approximations,

Jan 1, 2010

By Carlos Magno Palacios Arbizu

La calidad total es la estrategia que busca la mejorar la productividad y eficiencia de los productos que ofrece -en tanto sean reconocidos por este valor-, de forma que genera competitividad en las organizaciones peruanas y se presenta como respuesta a nuevos enfoques de gestión surgidos ante el proceso de globalización. En este sentido, el presente trabajo analiza la forma del avance en el nuevo enfoque de gestión de las empresas mineras, para así proponer alternativas de tratamiento e implementación de un modelo basado en la Calidad Total, de manera que esté alineado dentro de un sector que tenga características propias y diferenciadas de organizaciones de otros sectores productivos.

Sep 12, 2005