Search Documents

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

By S. Kelebek

DETA exhibits a highly selective depressant action on pyrrhotite without adversely affecting the collectorless flotability of pentlandite and chalcopyrite in nickel-copper ores of the Sudbury region. A simplified Eh-pH diagram has been constructed to illustrate the extended stability of elemental sulphur and to explain the collectorless flotation of pentlandite and chalcopyrite. Cu and Ni ions, which are known to exist on the surface of pyrrhotite, promote the flotation of this mineral whether a collector is present or not. Thermodynamic calculations indicate that the action of DETA involves the sequestration of Cu and Ni ions from surfaces under a wide range of redox conditions; analysis of flotation test filtrate indicates as much as a 20-fold increase in the concentration of Ni and Cu ions. It appears that DETA may enhance the self-hydrophobicity of chalcopyrite and pentlandite by exposing more of the sulphur-rich surface sites for bubble contact in flotation. There are various possible explanations for its depression of pyrrhotite

Jun 18, 1905

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By Hirohide Kamada, Gustavo Scarpim

The increase in industrial demand is responsible for a consequent evolution in the process of injection of aluminum under pressure (Die Casting) to achieve requirements such as; greater geometric complexity of injected parts, larger dimensions, hard-filled cavities, thin walls, and more refined mechanical and aesthetic requirements. Thus, the industries have searched for sensible increases in pressure and injection speed, always combining the best resistance and performance of the wells submitted to the new process conditions. The need for more aggressive applications for the cavities means that there is a constant evolution of the entire production chain in the manufacture of molds, passing through several processes, among them; machining, designs with complex engineering solutions, refining in the process of heat treatments and surface treatments. Allied to these needs, high performance steels manufactured by differentiated processes with high fracture resistance, hot strength and wear must be selected. This work aims to present the main factors considered in the development of high performance molds, the engineering of materials involved, technological trends and technical engineering solutions for the different variables of the die casting process.

Nov 22, 2018

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By P J. B Fransen

Several spatially and/or temporally distinct phases of epithermal activity can be recognised in the Horohoro-Matahana Basin area of the Taupo Volcanic Zone. In the northern Matahana Basin a 140 - 350 ka age range is proposed for mineralised debris flow clasts and related (?) epithermal  mineralisation intersected in a recent drillhole. To the east, a ca. 40 - 50 ka age range is suggested for epithermal activity in the Waikaukau alteration zone which was focused along the Guthrie Fault. Hydrothermal explosion breccias occur over 13 km within the Guthrie Graben, and are probably sourced from vents in the south. Assuming a common origin, these breccias are constrained to a 45 - 50 ka age range. Within the Horohoro hydrothermal system (around the present hot spring), older (15 - 50 ka) and younger (0 - 15 ka) features can be distinguished.

Jan 1, 1991

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. L. Virta

Four companies mined ball clay in four states during 2005. They included H.C. Spinks Clay (owned by Franklin Minerals), Kentucky-Tennessee Clay (owned by Imerys), Old Hickory Clay and Unimin. Production was estimated to be 1.32 Mt (1.45 million st) valued at $53.3 million, based on the results of a preliminary survey of the ball clay industry. Production in 2004 was 1.22 Mt (1.34 million st) valued at $54.1 million. Tennessee was the leading ball clay producer state with 61 percent of domestic production, followed by Texas, Mississippi and Kentucky.

Jan 1, 2006

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

By R. E. Dye

Introduction Research concerning all phases of hoisting practice, but more particularly the causes and prevention of hoisting rope deterioration and the improvement of safety dogs 158 for shaft conveyances, has been carried on intensively for the past three years in the Province of Ontario. Prior to the hoisting accident at the Paymaster mine on February 2nd, 1945, there had been no fatalities in the Province due to a hoisting rope failure. It was probably on this account that little original research on hoisting problems had been undertaken here and that the mining industry had been content to look to British, South African, and United States investigators for new developments in this field. Except for the Paymaster accident this might still be the case since, in any industry, it is apparently necessary for a serious accident to occur before any extensive programme of preventive research is launched. When this accident occurred, the Government of Ontario, with the close co-operation of the Paymaster officials and the mining industry as a whole, took immediate steps to determine the cause. A five-man, non-industry committee, selected from the Faculty of the University of Toronto with Dean C. R. Young as Chairman, was appointed by the Government, and a three-man Committee consisting of R. D. Parker, General Superintendent of the International Nickel Company of Canada, Limited, R. L. Healy, General Manager of Wright Hargreaves Mines, Limited, and R. E. Dye, General Manager of Dome Mines, Limited, with the latter acting as Chairman, was appointed by the Ontario Mining Association.

Jan 1, 1948