Search Documents

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

Predicting the future is a task that should always be delegated. If that is not possible, then stating your views confidently, but retrospectively, is preferable. Hindsight encourages clarity of thought and sharpens perception. When all else fails one can look back into history and see the trends, evaluate the current situation and project it a little way into the future - in this case 10 years. In exploration the rate of change has been increasing over the past 20 years. With expected developments in technology, legislation, and their sociological impacts, we will see such rapid change over the next decade as to make us uncomfortable, unless we are prepared for it.   The social obligations of our industry also have changed enormously over the past 20 years and are still changing. This will lead to further changes in the way we conduct our business if we wish to stay in business. As exploration technology improves, a further dimension is added by the expectations of the communities in which we operate. This extra dimension needs to be quantified so that we not only keep up with current developments but also get ahead of the game. This paper is based on the New Zealand experience, some of which will be familiar to mineral explorers in other countries.

Jan 1, 1997

By George L. Wilhelm

Timber support of mine openings continues to be an effective system for ground support, due to its avail¬ability, flexibility, and ease of installation. Timber support of mine openings as a primary method to support loose rock has been replaced to a large extent by rockbolting and by filling systems. How¬ever, the many designs of square-set timber and varia¬tions of crib and stull support that have been developed to suit many stope configurations have proven reliable over many years of application. Integrated in modern excavation and stoping methods, timber remains an im¬portant ground support material for today's mines. ADVANTAGES AND DISADVANTAGES OF TIMBER SYSTEMS Timber, when used as a part of the total support system, is recognized for its unique support properties. More than a cover to prevent minor falls of ground, timber systems have been carefully designed to provide adequate support with sufficient compressive qualities to achieve a safe working environment in extremely diffi¬cult ground conditions. In some cases, a timber support method is designed to yield while retaining its protec¬tive support qualities. Little or no initial investment in equipment or plant is required for incorporating timber into the mining support system. Low cost cutoff saws and portable chain saws are sufficient equipment for effective use of dimen¬sioned (sawed) or round (stull) timber support. Until recently, small sawmills of various complexity were com¬mon at mine surface plants. Sawmills at the mine sites have generally been replaced by timber vendors' mills. Suppliers have been able to use efficient cutting and lumber handling methods to reduce the cost of mine timbers. Most suppliers will package dimensioned mine timber into bundles that are suitable for handling down mine shafts and on level conveyances. The principal disadvantage of timber as a support method is higher material cost and labor cost associated with its labor-intensive installation. Furthermore, stand¬ing timber reserves of mine quality wood are in short supply in some areas, and heavy competition exists for alternative uses of the timber supplies. Vendors are reluctant to supply large cross section dimension tim¬bers relatively free of defects. Some mine operations require 4.8-m (16-ft) lengths of firm timber over 0.09 m2 (144 sq in.) in section and these are difficult to obtain in large quantities. APPLICATION OF TIMBER FOR MINE SUPPORTS Timber used in mine support has been cut from many species of trees. A firm hardwood with physical properties similar to western Douglas fir has been pre¬ferred in the US. Other harder and softer woods, how¬ever, have been used when readily available or where the specific strength or crushing quality of the wood is a desired specification of the support system design. Hard¬ wood, commonly oak, has been used where maximum crushing resistance is required. Mahogany and fir are widely used for shaft guide timber. Normally, timber is used with its core axis parallel to the long axis of the timber dimension. However, in some cases, it is placed normal to its core in a "butt" log position, so as to provide maximum resistance to abrasion of the ore passage adjacent to the cut end of the block. By selective placement of timber block¬ing, controlled resistance to ground closure can be achieved which will prevent early failure of primary sup¬port members of the timber structure. Timber is widely used in modern mining operations as a construction member for chute-lip support. These designs are tailored to each operation to conform to the dimensions of the haulage equipment being used. As a construction material, wood requires none of the spe¬cial equipment necessary for placement of concrete or steel support. Placement of these alternate support ma¬terials requires carefully dimensioned and engineered excavation for their installation. Wood can be easily sawed to fit on location. The successful use of timber in heavy ground de¬pends on the careful and accurate placement of block¬ing and bracing to achieve the controlled yielding re¬sistance needed to support the mine opening. Similarly, frequency, size, and placement of top and bottom block¬ing stulls in flat-bedded deposits are carefully determined to provide adequate support at the mining face. Con¬trolled caving through failure of the stulls may be required as the scope retreats from the earlier mined-out sections. The support program must achieve both of these dimensionless qualities by specification of stull frequency and size. The utility of the square set-system of ground sup¬port and timber support is described in Chap. 2, re¬printed from US Bureau of Mines Information Circular 6691. Four examples of effective use of timber for support of stoping and other mine openings are pre¬sented in other chapters in this section. The Gilman mine's use of Mitchell slice stoping described in Chap. 3 is an early modification of the square-set mining system. This application proved reli¬able for heavy ground and overcame some of the dis¬advantages of conventional square-set timber. Chap. 4 describes the Burgin mine's use of timber with other reinforcement material. This combination of materials achieved high strength and control with yielding com¬ponent members necessary for heavy, squeezing ground. Chap. 5 describes the Bunker Hill mine's use of square¬set timber in a new configuration that provides an effi¬cient and safe support for stoping using small load¬haul-dump (LHD) mobile equipment. Chap. 6 describes some considerations in placing the widely used stull in bedded ore deposits. Finally, in Chap. 7, cost calcula¬tions for

Jan 1, 1982

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By Robert A. Bradburn

The Bureau of Mines has developed a miniature, portable two-level oxygen-deficiency alarm and produced three prototype models. Each operates from a 4.2-v dc power source, and the highest current drain of any model is 80 ma. An electrochemical cell, which produces an electrical output in proportion to the partial pressure of oxygen to which it is exposed, is used as an oxygen detector. The output of the cell is applied to an electronic circuit that detects two different levels of oxygen percentage below that of normal air, and produces distinct audible signals at these levels. The hazard alarm mode is activated when the oxygen percentage first drops below normal and produces a 500-cps "beep" tone with an intermittency of 1 cps. The danger mode produces a continuous 500-cps audible signal when the oxygen percentage drops still lower.

Jan 1, 1968

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By N Cann

In the 10 years from 1998 to 2008 the annual number of fatalities in the Australian mining industry has plateaued (MCA, 2007-08 and abc.net.au website). Despite significant efforts to eliminate fatalities, this is not a comfortable statistic in this very public performance indicator.GHD has been working with the mining and minerals processing industry to identify the key risks that lead to fatalities utilising a semi quantitative risk assessment technique (SQRA®), initially developed to assist Major Hazards Facilities prepare Safety Cases (OH&S, 2007-08) in response to the Longford Incident in 1998 (Dawson and Brooks, 1999).Workshop cross functional teams are assembled from the sites and led by the GHD facilitators to identify the incident types that can have fatal consequences, the causes of those incidents and the controls that are utilised (or could be utilised) to reduce the risk. The risks for each incident type are quantified to produce a risk profile for the facility and the critical controls – the controls that have the greatest impact at reducing the risk of fatality – are selected. These controls are assessed for their adequacy and improvement actions are identified. Prioritisation of the actions is achieved by re-estimating the incident risk profiles.A review has been undertaken using a small sample from the more than 100 individual studies that GHD has completed at mining and minerals processing sites. The five most significant risks reported by sites are:1. Fall from Heights,2. Vehicle/ Vehicle and Vehicle/Pedestrian interactions,3. Entanglement,4. Molten Metals and Materials, and5. Electricity.The most significant reductions in risk identified were found to be by implementing engineering controls. Examples include:1. Chutes to contain splashes and spills of molten materials,2. Redesigning instrument and equipment layouts to take personnel away form high risk areas,3. Designing remotely operated equipment to remove personnel away from high risk areas,4. Proper fire fighting equipment provisions such as deluges around flammable materials, and5. Adequate risk assessment to ensure equipment is designed to handle the real situations and not a design case to meet an arbitrary specification.All of these cases and many of the actions identified in the studies could have been handled through better design and construction early in the life of a project rather than retrospectively fitted after operations have begun.

Aug 8, 2011

The additive property of dispersion variances was found experimentally by D.G. Krige using data from the gold deposits of the Witwatersrand. In this property, called ?Krige?s relationship?, the dispersion of a small unit, v, within the deposit is equal to the sum of the dispersion of v within a bigger unit, V, and the dispersion of these units, V, within the deposit, D. It is known that the variance of the grades decreases as the support increases, the so-called volume-variance relationship. To analyse volume-variance and Krige?s relationship, the methodology herein proposed combines blending piles and geostatistical simulation to simulate the in situ and the pile grade variability. Variability reduction in large piles is based on the volume-variance relationship, i.e. the larger the support, the smaller the variability (assuming perfect mix). Based on a pre-defined mining sequence to select the blocks that will form each pile for each simulated block model, the statistical fluctuation of the grades derived from real piles can be simulated. Using this methodology, one can evaluate within a certain time period the expected grade variability for various pile sizes, and also calculate the Krige?s relationship between the small blocks and the piles of different sizes. A real case study using a large Brazilian iron ore deposit illustrates the methodology and demonstrates the validity of the results.

Jan 1, 2014