Search Documents

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

The Effect of Using Different Comminution Procedures on the Flotation of Platinum Group Minerals The use of High Pressure Grinding Rollers (HPGR) has been widely reported to have major benefits in the treatment of minerals such as iron ore and diamonds. To date there have been few investigations into its use in the treatment of ores containing Platinum Group Minerals (PGMs). HPGRs are known to reduce energy consumption and wear costs and improve the throughput in the circuit. In the present investigation the effect of the comparative use of HPGR and conventional crushing in combination with either dry or wet rod milling on the flotation of PGMs was studied using batch flotation. Previous studies of a base metal sulfide ores had shown that either HPGR or conventional crushing followed by dry milling produced the highest grades and recoveries. However in the present study it was observed that a similar treatment produced the worst results and the highest grades and recoveries were obtained for the case of conventional crushing in combination with wet milling. The HPGR showed no advantages in terms of flotation performance and dry milling produced particularly poor flotation results. The results were investigated further using various surface characterisation techniques in order to determine the reason for the decrease in grades and recoveries of platinum when using dry milling and HPGR as opposed to the case for base metal sulfides. The feed and product samples were analysed using ToF-SIMS, XPS and MLA. The paper will propose reasons to explain the different flotation behaviour of the two ore types following the various comminution processes focusing on the surface characteristics of the ores, the particle size distribution and the pulp chemistry.

Sep 13, 2010

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

From time to time efforts have been made to classify rocks according to their hardness, toughness and abrasiveness, and to use these classifications to provide an indication of the ease or difficulty with which they may be drilled. However, rocks classified as of similar type on this basis may vary considerably in their .resistance to the penetration of a rock drill bit due to differences in their physical state.For instance, fine grained rocks of granular texture are more difficult to drill than equivalent' rocks of coarser structure, altered rocks drill more readily than unaltered ones, and silicified rocks usually exceedingly hard and tough may be so shattered by movement as to be drilled at a rate comparable to quite soft rocks. Therefore, considerable latitude has existed in this method of defining their drillability, and no values generally acceptable have materiaJised; so that, when the drilling properties of rocks are discussed, it is common practice to refer to their hardness or toughness in a greater or lesser degree depending to some extent on the emotional state of the drill runner.REFERENCES AND STANDARDSThe 'introduction of tungsten-carbide tipped rock-drill bits for use with percussion rock-drills has thrown increasing emphasis on the need for defining a rock's resistance to penetration in a more concise and generally acceptable...

Jan 1, 1950

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By P. M. Lin

A subsidence monitoring program over a longwall panel was established (1) to explore the impacts of dynamic subsidence on the ground surface and structures and (2) to correlate the movements between the structures and their corresponding points on the ground. The program consisted of a transverse line survey and a series of survey points around the structures on the ground surface and their corresponding survey points on the exterior walls of the structures. The vertical displacement of each point can be expressed as: where Si is subsidence at i point; Sif is the final subsidence at i point; F is face location in terms of distance from the i point and SD is seam depth. The development of subsidence can be divided into five stages. Damage to the structures starts at the beginning of the second stage, The maximum damage developed in the middle of the third stage. The relationship of the vertical displacement between ground surface and structures can be expressed as: G = aH + b where G is ground displacement, H is structures displacement, and a and b are constants. The relationship is linear. However, the strain is non-linear and more complicated because of the interaction of the ground surface and structure.

Jan 1, 1989

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By Gyan S. Rajhans

"The strategy of fibrous dust sampling is discussed, various sampiing methods are critically reviewed .and their application to coal dust is demonstrated. Fibre counting is described in detail. An attempt is made to explain the basis of determining the threshold limit value of asbestos and other dusts. The paper also discusses such dust control methods as enclosure of the process, effective local exhaust ventilation, segregation, substitution, wet processing and continuous monitoring of the return air for recirculation."

Jan 1, 1970

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Part III reviewed the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona. Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and a P80 of 6 to 7 µm), pressure leaching at 160ºC with 1,380 kPa (200 psig) oxygen overpressure, DEW to produce LME Grade A cathode, recycling some of the lean electrolyte to the pressure leaching step, and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an acid-autogenous process for pressure leaching. This paper (Part IV) discusses the development and design of a full-scale commercial application for the Morenci operation in Arizona.

Jan 1, 2007

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

The New South Wales coal industry is a highly mechanised well organised industry which has developed from an annual production of slightly less than 13 million tons in 1950 to over 33 million tons in 1969. Although continuous miners were not introduced into the mines until 1950, by Jillle 1969 the percentage of coal won by these units was 87.3. The paper describes mining conditions in the various coalfields of the State, their complexities and problems and how these have been dealt with. The introduction of fully mechanised long wall faces has presented a challenge which has been accepted and descriptions of systems in use are discussed. Major expansion of the industry is anticipated to meet the requirements of the growing Australian steel industry, for local power generation and to meet the increasing demands of overseas markets.

Jan 1, 1971