Search Documents

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By L. B. Clarke

The optimal maintenance and control of the air flow and pressure distribution in a mine network are achieved by the correct positioning of the mine fans and regulators within the mine ventilation circuit. The principal considerations are the location of the main and underground fans or regulators and the attendant control of mine leakage. Air flow control is achieved by either passive or active regulation. Passive regulation adds resistance, usually in the form of a regulating door. Active regulation adds pressure sources in the form of underground booster fans. Ventilation engineers are increasingly turning to analytical tools to assist them in the design and operation of ventilation systems. The application of computer methods, formal optimisation methods and numerical solution methods is outlined

Jul 1, 1996

By Michael MacMillan

The mining industry has always operated under intense public scrutiny. Community expectations, investor pressures, regulatory obligations, and environmental oversight create a uniquely complex communications environment. In recent years, technological change, climate urgency, and geopolitics have reshaped how the industry communicates its role and value. The rise of artificial intelligence in the information ecosystem represents yet another fundamental shift. As AI evolves, an organization’s reputation will no longer be shaped solely through human interactions, media coverage, social activity, or corporate disclosure. Increasingly, public understanding depends on how AI systems interpret and represent company information. These systems influence search results, conversational tools, news aggregation, social discourse, and even investor intelligence platforms. As AI-generated summaries, answers, and narratives become the default interface for stakeholders, they also become authoritative in shaping trust. For mining companies, this creates both risk and opportunity. The organizations that recognize how AI reads, prioritizes, and amplifies information will be better positioned to build trust. Those that remain silent or rely on traditional communication methods may find their reputations being algorithmically defined without their participation. This paper explores how mining companies can proactively engineer their reputations in the age of AI.

Jan 1, 2026

By Prosper Lamothe

El presente texto describe la metodología ad-hoc para evaluar proyectos de Inversión estratégicos a través de la flexibilidad y la teoría de opciones reales. La clave de dicho enfoque metodológico radica en realizar la mejor proyección del precio de los metales aplicando las mejores prácticas mundiales al respecto. Para ello, se analizan una gran variedad de modelos concluyendo que el mejor modelo a aplicar, debe ser la simulación del precio del metal con reversión a la media con saltos de tipo aleatorio.

Sep 9, 2007

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

All previous attempts to cut rock in boring by means of revolving steel cutters have failed, chiefly in consequence of the mis-shapen teeth grinding the rock and themselves simultaneously, until, after a very few revolutions, the points of the cutters were so worn that it was impossible to force them into the strata. The diamond drilling plant being cumbrous, complicated, and costly, and seeing that fully 70 per cent of the boring generally needed is in what is known as the" milder strata," it will be readily understood that much of the work done will not pay a dividend on the outlay, so great is the cost of removal, the wear and tear of the machinery, and the loss of diamonds. The Calyx Drill, however, invented by Mr. F. Harley Davis, has been constructed so as to overcome these difficulties, and will penetrate quickly and .at a low cost this 70 per cent. of the milder strata. The Drill has taken ten years' hard work and thought to bring it to its present state of perfection, and it will now drill with steel cutters the 70 per cent of the work performed by the diamond drills at a greater speed and at about one third the cost of the latter.The utility of the diamond drill for certain work is undeniable, but it cannot by any means be described as a machine of general popular usefulness that is to say, it is quite beyond the reach of the great masses of mankind.

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

By Edward Capillon

THE problem of scrap is probably of greater importance inn the production of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of the base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is. not generally feasible to assay every shop remelt it follows that the possibilities of lost values are large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base, metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys.

Jan 1, 1930

By Tapan Goswami

The expectation from the blasting engineers and shotfirers is often that explosives will perform optimally at all times. However, in reality, non-ideal situations exist on mine sites and occurrences of poor explosives performance are common. Often the cause is difficult to identify. Having a good application technique and analysis skills will minimise the risk of poor performance. This paper will discuss the experiences gained by the author while blasting in the Hunter Valley, Australia.

Jan 1, 2003

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935