Search Documents

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By A R. Bye

Energy comes at great cost to our world and societies and therefore we should use it wisely and optimally. Societal pressure is enforcing this and the industry must respond by being proactive.The mine-to-mill approach to integrated mine and semi-autogenous grinding (SAG) mill optimisation demonstrated that throughput gains of up to 20 per cent could be obtained through a closer match of blasted run-of-mine ore to the feed best treated by a SAG mill. Since that approach was developed, new drivers have risen to prominence including environmental costs and impact of energy, water, waste. This is set against a backdrop of reducing ore grade and increasing demand that is pushing up our impact on the environment. The new challenges demand new approaches.This paper explores the opportunities in taking traditional approaches to optimisation to new levels of two-way integration and incorporating potentials for ore upgrade into circuit design. The new mantra may be æflexible circuitsÆ û designing and building for the present and the future by allowing for the uptake of new and future technology.

Jan 1, 2009

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion's share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, 'What is the best way to power this mine?', they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective, and quantitative decision-making approaches to evaluating alternative energy-delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health, and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision-making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision-making tool and the decision tree based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers, and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow-reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2013

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991

By J. R. Thoenen, J. D. Warne

"INTRODUCTION Red-iron-ore deposits in northeast Alabama have been exploited at vari¬ous times for nearly 6o years. About 3-1/2 million tons of ore have been produced in the Gadsden district; but mining activity has been dormant since 1926, and furnaces within this section of the State now suffer a shortage of red ore.To alleviate these shortages, work by-the Bureau of Mines was recommended after preliminary investigations. 4/5/ Diamond drilling, to determine the lateral and vertical extent of ores of known deposits in Greasy Cove and on Shinbone Ridge, was done from August 1946 to May 1947, as Project 9-106, Alabama Red Iron Ore. Three holes were drilled in each area.ASKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they- make the greatest possible contributions to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as possible after its conclusion. The Mining Division, Lowell B. Moon, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests."

Jun 1, 1948

By Manuel Gomez

Published experimental coke data from a pilot plant slot-type oven were examined by statistical regression analysis. Quantitative relationships were found to exist between the coking rate, bulk density, and fine grinding of the coal, sole-oven expansion, volatile matter, moisture, ash, and carbon con-tent of the coal and coke parameters indicative of size and strength. Regression equations developed from coke data were shown to yield computed values that were in good agreement with experimental results for 11 coke properties. Prediction equations developed were evaluated with an independent set of data. Present results indicate that the variables cited undergo much interaction and the sum of these interactions determines coke size and strength.

Jan 1, 1967

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

By S. Weiss, E. Espinoza

The El Sauzal gold-silver deposit is a high-sulfidation, epithermal precious-metals deposit hosted by an east-dipping sequence of dacitic and rhyolitic pyroclastic and debris-flow units of probable Oligocene age. Total gold production since startup in late 2004 is approximately 450,000 oz. of gold. Above the sulfide boundary gold is mainly disseminated as small grains interstitial to alunite, kaolinite and quartz. The majority of the ore is found in quartz-alunite-kaolinite altered rock that mantles tabular to irregular silicic cores of vuggy, residual quartz ±kaolinite ±dickite. Grade domains are modelled as subhorizontal to east and southeast-dipping. Higher-grade domains cut across alteration zones and also coincide with transitions from vuggy quartz to quartz-alunite-kaolinite. The highest grades are commonly found marginal to vuggy quartz in transitional, hematite-rich quartz-kaolinite and quartz-alunite-kaolinite rock.

Jan 1, 2007

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956