Search Documents

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020

By Paul Downing

A typical day for a blasting company includes what seems to be an infinite list of tasks dealing with numbers. Whether determining the exact amount of explosives material in inventory, the number of holes in the shot, the exact distance from the blast site to the nearest exposure, or the capacity of bulk hoppers, the accuracy of numbers is key to ensuring the safety of the public, property and personnel.

Jan 1, 2008

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By Frank G. Wickert

One key to maintaining successful mining operations in today?s global economy is in having the ability to access real-time machine operating data ([1] G. Brown, B. Ebacher, W. Koellner,2000)([2] Brochure of Siemens E&A, Order Number 141000-1). With recent and ongoing advances in mining equipment systems it is imperative that mine managers have full knowledge of the status of their equipment at any given point in time. This knowledge is critical to ensuring that the productivity of each and every machine is maximized. Knowledge of machine status is only the first step, however, in controlling and optimizing a piece of mining equipment. Computer based diagnostic systems, traditionally offered on mining equipment, have provided a link for collecting data and trouble-shooting problems as they occur. One problem existed, though, that those systems stopped short of providing full drive systems access. A maintenance technician could see the data but to make critical adjustments or make repairs the technician needed to be on the machine. In extreme cases the machine would be down until OEM assistance could reach the mine site. The key then to reducing down-time and maximizing machine productivity was creating a system that could not only monitor drive systems but also provide remote access to those systems. Essentially a link needed to be created through which a technician could gain drive access remotely then make adjustments or repairs without being on the piece of equipment. This paper will introduce AccessDirectTM, a new remote diagnostic system for Bucyrus mining shovels and draglines. AccessDirectTM combines all three important elements of remote diagnostics: ? Vital Signs and Production Monitoring (SiRAS-M) ? Automatic analysis (SiRAS-A) of faults, and tracking of trends for preventive and reliability centered maintenance , and ? Fast, direct Intervention (SiRAS ? I) for troubleshooting support, repairs, and system optimization.

May 1, 2002

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By D. Harrington

The mining industry of the United States has for many years possessed the dubious aistinction of having the poorest accident rate of all of the major lines of industrial endeavor in this country, and until recently there ras little or nothing to show that any material improvement might be expected. However, there are now numerous trends indicating that the corner has ceen turned at last, and it is strongly hoped that the mining industry is likely to follow the railroads, the cement and other industries in operating with occurrence of only a reasonable amount of loss of life and limb through accidents. The complete accident figures for metal and nonmetallic mineral mining for 1931 are not yet available, but fragmentary data shor that 1831 vill un- questionably have very low accident rates, probably the lowest in the history of our metal mines. One underground metal mine has produced over 14,000,000 tons of copper ore rithout a fatality; another metal mining company with an electric slovel operation has handled upwards of 75,000,000 tons of material, copper ore and waste, without the occurrence of a fatality; an iron-ore compan, which orns six mines (three underground, three open pit), has operated every one for a year or more without a lost-time accident with a con- siderable number of employees and a large production; and alot.er iron-ore producer with 30 mines and about 3,000 employees as an average of nearly 10 months of operation in 1931 without a lost-time accident. umerous other wonderful safety records of metal mines in 1931 indicate unmistaimbly tat the record of the noncoal mining industry of the United States as a role in 1931 will undoubtedly be found to be excellent. According to the latest relatively complete figures (those of 1930) available for the coal industry, fewer than 650,000 persons are employed in and around the coal mines of the United States, the figures indicating at a little over 493,000 people are engaged in bituminous mining and a little under 151,CCO in anthracite mining. Bureau of Mines complete figures suc that 2,053 persons were killed and 103,821 non-fatally injured in our coal

Dec 1, 1932

By Robert J. Kuhne

The Iron Ore Company of Canada has successfully employed advanced process control (APC) to optimize the operation of their induration machines. A significant increase in machine throughput and a reduction in fired pellet quality giveaway were observed following the APC implementation on all six machines. This paper discusses the opportunity for process control optimization in induration, reviews the property estimation and multivariable control technologies, and describes how the IOCC control strategy captured this opportunity. APC performance data is presented. The dependence of APC performance on control room operator acceptance, process equipment and instrumentation is highlighted.

May 1, 2007

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

Jan 1, 1886