Search Documents

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

By L. Russell Van Wert

DURING an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. CLEAVAGE STRUCTURE IN HEAT-TREATED MUNTZ METAL Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decomposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions-austenite and quenched Muntz metal- are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent, gamma iron, at ordinary temperatures is below its normal stable range) whereas the metastability of the quenched Muntz metal is the result of supersaturation.

Jan 1, 1929

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone; its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly, Coking, but which have compensating features. Blending also allows better exploitation of coking coal reserves. Several applications of blending have been reviewed with regard to coal producers and exporters, as well as coal users. The possibility of extracting a coking coal fraction from fuel coals is discussed. Blending systems and the coking of coal are also briefly reviewed.

Jan 1, 1971

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013

By L Dixon, J Carter, K Auyong

Fourier transform infrared (FTIR) spectroscopy and other near infrared (NIR) tools have been used in the bauxite industry for many years. Infrared spectroscopy exploits the differences in chemical composition and lattice structure to produce a characteristic response. Spectral devices, such as those from ASD Inc and the HyLoggerTM, provide qualitative mineralogical data targeted towards hydrated minerals detected in the near and short wave infrared region. The FTIR spectrum extends into the mid and thermal infrared range and can therefore respond to the presence of silicates and oxides, in addition to hydrates and carbonates.The key to successful utilisation of infrared spectra, however, is the interpretation methodology. In this study, FTIR spectra were calibrated against quantitative X-ray diffraction data for the determination of the mineralogy of iron ore. A full pattern profiling machine learning technique was utilised for the calibration, and the assessment of the regressions determined from an independent validation set. The abundance of key minerals – hematite, goethite, kaolinite and quartz – were determined and the results correlated against X-ray fluorescence assays and loss on ignition data. The results of the study indicate that spectral techniques using a full-pattern profiling machine learning approach and artificial neural networks can be used successfully to obtain objective and quantitative mineralogical data to support field observations and analytical results for iron ore resource modelling. A comparison of this technique to the cost, quality and timeliness of other quantitative mineralogy tools is also made.CITATION:Carter, J, Auyong, K and Dixon, L, 2017. Determination of iron ore mineralogy using Fourier transform infrared spectroscopy and machine learning, in Proceedings Iron Ore 2017, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010

By H Phillips, A Spaeth, B Belle

There are several well-known, extensively researched and tested methods of suppressing a coalmine methane and coal dust explosion. The choice of method used is dependent on the legislative requirements of each country, which in turn are influenced by mining conditions in that jurisdiction. For example, seam gas content and the dustiness of the coal will combine to create the hazard, while the physical and chemical properties of the seam might influence the possibility of ignition sources such as frictional ignitions. The mining method and layout will also influence the choice of preventative or proactive suppression devices. The decision as to which method is approved and adopted should be based on currently tested and available technology and the latest research outcomes, and should be subjected to a rigorous risk assessment, since a methane explosion propagating into a coal dust explosion cannot be countenanced.Every new technology must undergo stringent tests and these tests must be certified by accredited research facilities or laboratories. Upon approval, an explosion suppression system or the critical components of such a system should be tested in a more realistic environment. This environment can ideally be found in an operating underground mining section for evaluation purposes. Based on the insight gathered in such an environment, a realistic evaluation of the effectiveness of a potential system can be carried out. The explosion suppression system described in this paper has been tested on numerous occasions at accredited test facilities. The technology described in this paper has been used in various applications in underground coalmines and has been adapted to fulfil and exceed the requirements set out for methods currently in use. This paper describes the underground evaluation results of the latest technology in active suppression systems as used on continuous miners was adopted to perform as a roadway explosion barrier.CITATION:Spaeth, A, Belle, B and Phillips, H, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Australian Mine Vent Conference 2017, pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Seth Pollak, Jon Hurt, Mark Havekost, David Vardiman, James Schick

"INTRODUCTION The Long Baseline Neutrino Facility (LBNF) Far Site Conventional Facilities are proposed to be sited at the Sanford Underground Research Facility (SURF) located within the former Homestake Gold Mine in Lead, South Dakota. The project involves excavation and support of three large caverns which will house four 10 kT fiducial volume liquid argon (LAr) neutrino detectors and cryogenic equipment, as well as numerous ancillary connecting drifts and chambers. This paper describes the geological setting of the project, the geotechnical investigation undertaken nearly a mile underground and the challenges associated with collection of reliable data in a high stress and geologically complex environment. The layout for the new facility will be presented, along with a description of some of the constraints that will impact construction, including shaft access and working within an operating research facility. THE LBNF PROJECT The global neutrino physics community is coming together to develop a leading-edge, dual-site experiment for neutrino science and proton decay studies, the Deep Underground Neutrino Experiment (DUNE). The facility required for this experiment, the Long-Baseline Neutrino Facility (LBNF), will be an internationally designed, coordinated and funded program, comprising the world's highest-intensity neutrino beam at the Fermi National Accelerator Laboratory (Fermilab) in Batavia, IL and the infrastructure necessary to support massive deep underground cryogenic detectors 800 miles (1,300 km) downstream at the LBNF Far Site at the Sanford Underground Research Facility (SURF), in Lead, South Dakota. The Deep Underground Neutrino Experiment is expected to achieve transformative discoveries, making definitive determinations of neutrino properties, the dynamics of the supernovae that produced the heavy elements necessary for life, and the possibility of proton decay. Neutrinos created by the LBNF beamline will travel on the 1,300 km (800 mi) path shown in Figure 1 leading straight through the earth's crust to intercept DUNE's massive, cutting-edge neutrino detector at the Sanford Lab. No tunnel is needed as neutrinos pass easily through soil and rock rarely interacting with the matter. The DUNE far detector will consist of four modules, each of which will be housed in a cryostat containing 17,000 metric tons of liquid argon target material, providing a 10kT fiducial volume. The LBNF Far Site Conventional Facilities project will excavate and fit out a set of four caverns 4850 ft underground in which to place them."

Jan 1, 2016