Search Documents

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry For the years 1966-67. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent or disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By Peter L. Swanson

NIOSH has developed an automated PC-based seismic monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network (LAN) is a central feature of the system. Design requirements include (1) the use of lowcost, off-the-shelf, data acquisition and computer hardware, (2) the capability of automatically merging waveform data sets from different types of monitoring systems, (3) delivery of raw and processed data underground and on the surface, as well as to remote sites, and (4) automated data collection and processing over long periods of time without the need for human intervention. Current mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface and provide 20 to 40 stations within a radius of several kilometers. Event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's hardware and software components, examples of installations in hard-rock and coal mines, and a few observations from western U.S. longwall coal mines.

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By R. Blickensderfer

Maintaining an adequate supply of minerals and metals to meet national economic and strategic needs is the overall goal of the Bureau of Mines, U.S. Department of the Interior. One method of achieving this goal is to conserve scarce metals by cladding a plentiful base metal, such as iron, with a scarcer metal. To investigate cladding, a vacuum-rolling mill capable of rolling bimetal specimens at temperatures to 1,300° C in a residual gas pressure of 2 x 10-5 torr was established. Metals that were successfully bonded to iron included stainless steels, chromium, nickel, nickel alloys, copper, and several refractory metals including molybdenum and titanium. The effects of the rolling temperature, reduction in thickness, rolling speed, and residual air pressure on bonding strength and bend ductility of the bimetals were determined. Optimum rolling conditions produced bimetals with bond shear strength essentially equal to that of the iron base metal.

Jan 1, 1980

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

By Ernesto Zelaya P

En el Perú, muchas de las empresas mineras se desarrollaron por la configuración de sus yacimientos explotados. Sin embargo, también se generaron limitaciones y restricciones en el transporte, extracción de mineral y/o desmonte dentro de las operaciones mineras. En este sentido, el presente texto señala una forma de inversión a través de un sistema de izaje, donde se realice un costo menos y una mayor productividad en la Unidad Minera Animón – EACH S. A. C. (Pique Jacob Timmers) y en la Unidad Minera Andaychagua – U. P. Yauli (Pique Roberto Letts) que son partes integrantes de las operaciones mineras de Volcan Compañía Minera S. A. A

Sep 12, 2011

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By R. Balia

The upper part of the "Contatto Ovest" orebody, at the San Giovanni Pb-Zn sulphur mine (Sardinia, Italy), is mined by a sublevel caving method. With increasing mining depth, a progressive caving of the hanging wall and discontinuous subsidence occurs. The orebody, which is located very close to the contact between the Cambrian limestones and the Silurian shales, strikes NE-SW for more than 100 m and dips 75-80' NW. The limestone footwall is massive and strong while the hanging-wall consists of very weak shales. The mine considered is located near a town so that the observed subsidence effects must be taken into account for both stability of the nearby railway and houses and morphological and environmental impact. A limiting equilibrium analysis to predict the progress of hanging wall failure with increasing mining depth was used. A suitable computer program was developed for solving the model by a iterative procedure. The progressive hanging wall caving and its consequent superficial effects were predicted perfectly by means of the computer program used and later confirmed by a geophysical test (seismic tomography). Our study ends with a further analysis, carried out using the same procedure, which allows to have a different geometrical situation with the presence of a pillar to protect the mill area.

Jan 1, 1990

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007

By Kenneth L. Whitehead

After many years of research, the occurrence of pneumoconiosis, black lung disease, among miners has been related to the mass of respirable coal dust to which mining personnel have been exposed. Congress passed Public Law No. 91-173 in 1969, which limited the dust concentration of respirable dust allowed in the mine working areas to 2.0 mg /M3 as of December 31, 1972. As a result of these restrictions, much work has been done in determining methods of either eliminating or suppressing respirable dust. The purpose of this project is to determine the state-of-the-art in continuous mining machine bit technology, particularly with regard to dust production.

Jan 1, 1973

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By Terry J. Close

U.S. Bureau of Mines personnel studied the 33,900-acre Silver Peak Range North Wilderness Study Area (NV-060-338), in order to evaluate its identified mineral resources. The area studied lies between the towns of Silver Peak and Dyer, about 40 miles southwest of Tonopah, in Esmeralda County, Nevada. There are no producing mines in the area studied. However, development of Sunshine Mining Company?s Sixteen-to-One silver-gold mine, located in the Silver Peak mining district near the eastern edge of the study area in the early 19801s, has stimulated recent interest. The Sunshine Mining Company claimed two sites within the study area in 1985. Also, Intermountain Resources, Incorporated, located a group of claims at a prospect along the west side of the study area in the Dyer mining district, and in 1986, began drilling. Other claimants are holding two other claim groups by assessment. At the five currently (1987) held sites, precious metals occurrences are being investigated. There are no patented mining claims or mineral leases in the study area.

Jan 1, 1987

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015