Search Documents

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By Markus Timusk

This paper describes a research project that focuses on developing a diagnostic routine to assist in decision support for the condition based maintenance of mobile mining equipment subject to unsteady duty. The objective is to develop a general method for initial identification of mechanical faults in machinery operating under non-steady state conditions. The platform to be used for the experimental development and validation of the system is the swing machinery in an electric mining shovel operating in an open pit mining environment. The strategic approach that is proposed for the diagnostic routine will involve using novelty detection augmented by temporal classification.

May 1, 2004

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By Xuan Li

Aluminum slag is generated when aluminum metals are recycled through a smelting process in the presence of salt. There are small amounts of aluminum metals trapped in the aluminum slag. This research aims at evaluating the use of aluminum slag as an expansion agent for the production of lightweight concrete by taking advantage of the residual aluminum metals in the slag. The research identified key elements of producing lightweight concrete products through utilizing various mixture components including sodium hydroxide (NaOH), lime (CaO), cement, and gypsum. The volumetric expansion rate was investigated and the density and strength of the products were determined. The results show that aluminum slag can be utilized for the production of lightweight concrete products.

Jan 1, 2010

By Eric Low

Raising capital by issuing debt or equity is necessary in almost every corporation. In the field of corporate finance, the raising of capital is a heavily-studied topic. However, some of what is studied on this topic in corporate finance is not applicable in the mining industry. There are also many financing options that were created for the mining industry such as flow-through shares, prepaid forwards, and royalty sales. The cyclical nature of the industry makes the risk-return profile of financings more difficult to estimate than in other industries. Additionally, the methods used to assess firm value are different than other industries, as the values of orebodies are not included on balance sheets. For precious metals companies, which are a hedge against most other securities, there are additional complications with determining investor expectations and cost of equity. This thesis puts forth a decision-making framework to explain mine financing choices from the perspective of mining companies. The approach is threefold. First, all of the major equity and debt financing instruments available to mining companies are presented and analyzed. Each financing method is assessed on a wide range of criteria. Next, these concepts are applied in case studies of four companies: BHP Billiton, Barrick Gold, Teck Resources, and Noront Resources. For each company, the overall choice of financing methods is shown and analyzed. The effect of financing choices on the weighted average cost of capital (WACC) is calculated. The final section deals with case studies of individual mine finance decisions during the past two years.

May 1, 2011

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By R. Poulin, C. F. Gleeson

The Birimian rocks of the region are gold-bearing and show many similarities to those of Burkina Faso. All three greenstone belts (Goroual, Tera and Sirba) host gold-bearing quartz veins. It appears that, contrary to previous misconceptions, lateritic terrain is not an unfavourable environment for exploration geochemistry. This is demonstrated by the results for the Koma Bangou area, where soil and termite-mound geochemistry have been successfully used in the search for gold. Soil provides an effective sampling medium where it is shallower than about 2 m; there is evidence that some soil anomalies are enhanced by the presence of secondary (botryoidal) gold. In areas of thicker, allochthonous soil cover, termite-mound sampling is more effective. At Koma Bangou an identified resource of some 11 100 000 tonnes with an average gold grade of 2.44 g/t has been reported. The gold mineralisation occurs in quartz veins and stockworks aand in the wallrocks of shear and fault zones that trend N, NW and NE. The host rocks are a granodiorite-syenite porphyry and intermediate metavolcanic rocks and tuffs

Apr 1, 1996

By J R. Goff, R Carver, D S. Sheppard

The REGCHEM (Regional Exploration Geochemistry) stream sediment geochemistry database of open file mining company data, managed by GNS Science, was recently made accessible via the internet (http://maps.gns.cri.nz/website/minmap/). REGCHEM provides coverage of selected elements in mineral rich areas of New Zealand. Analysis of REGCHEM data highlights problems with inconsistencies between different surveys in terms of sampling methods, number and types of elements analysed, analytical techniques and detection limits. New, consistent multi-element geochemical surveys with national coverage are required. To test sampling, analytical and data treatment techniques for the new surveys, a pilot stream sediment geochemical survey was carried out in the Thames area, Hauraki Goldfield. Seventy samples were collected in an area of 220 km2 representing about one sample every 3 km2. The samples were analysed for 50 elements, mostly by XRF. &nbsp; Regional patterns are apparent in the concentrations of some elements. Several elements, such as As, Cd, Cu, K, Pb, Sb, Se, and Zn exhibit anomalous concentrations mainly in the western part of the study area, related to Au-Ag-Zn-Pb-Cu epithermal quartz veins and porphyry Cu occurrences in hydrothermally altered andesitic terrane. &nbsp; Mercury is anomalous in southern samples, reflecting cinnabar occurrences in the Kauaeranga valley (eg Mangakirikiri), and the occurrence of cinnabar as a late stage mineral in some of the Thames epithermal veins. Ba and U are anomalous in the eastern samples, and these anomalies are probably related to the presence of rhyolitic rocks in the eastern part of the project area.

Jan 1, 2006

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By L. Chunpongtong

The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958