Search Documents

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By S. M. Carpenter

In response to the FY2008 Consolidated Appropriations Act (H.R. 2764; Public Law 110?161), the United States Environmental Protection Agency (USEPA) issued the final Mandatory Reporting of Greenhouse Gases Rule (MRR). The rule, signed by the USEPA Administrator, Lisa Jackson, on September 22, 2009, requires reporting of greenhouse gas (GHG) emissions from large sources and suppliers in the United States, and is intended to collect accurate and timely emissions data to inform future policy decisions. The MRR will go into effect on January 1, 2010, and a report of the total emissions for calendar year 2010 will be due to the USEPA by March 31, 2011. Under the final MRR, suppliers of fossil fuels or industrial greenhouse gases, manufacturers of vehicles and engines, and certain facilities that emit 25,000 metric tons or more per year of GHG emissions are required to submit annual reports to the USEPA. The gases covered by the rule are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFC), perfluorocarbons (PFC), sulfur hexafluoride (SF6), and other fluorinated gases as outlined in Table A-1 of Subpart A of the MRR, which is also provided in Appendix A of this report.

Jan 1, 2011

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

By J. Dahner

Total milling cost is composed of energy, liner and grinding media costs. In primary high ball load milling, the grinding media play the biggest role in total milling cost. This cost can be drastically reduced by improving the impact condition inside the mill. The impact condition inside the mill is influenced by shell liner design (as well as feed end and discharge design) and the type of discharge. The improvement of the impact condition will result in a significant decrease in grinding media consumption. The softened impact condition allows for better alloy optimization, resulting in a further reduction in grinding media consumption. Optimized liner design can also improve energy consumption as less energy is wasted in the projection of the grinding media. Magotteaux utilizes tools to simulate and show the grinding media trajectories for shell and end liners. This paper will present some practical examples where the media and energy consumption can be or has been reduced by optimizing liner design. Keywords Comminution, grinding, liner design, grinding media wear.

Jan 1, 2011

By Michael MacMillan

The mining industry has always operated under intense public scrutiny. Community expectations, investor pressures, regulatory obligations, and environmental oversight create a uniquely complex communications environment. In recent years, technological change, climate urgency, and geopolitics have reshaped how the industry communicates its role and value. The rise of artificial intelligence in the information ecosystem represents yet another fundamental shift. As AI evolves, an organization’s reputation will no longer be shaped solely through human interactions, media coverage, social activity, or corporate disclosure. Increasingly, public understanding depends on how AI systems interpret and represent company information. These systems influence search results, conversational tools, news aggregation, social discourse, and even investor intelligence platforms. As AI-generated summaries, answers, and narratives become the default interface for stakeholders, they also become authoritative in shaping trust. For mining companies, this creates both risk and opportunity. The organizations that recognize how AI reads, prioritizes, and amplifies information will be better positioned to build trust. Those that remain silent or rely on traditional communication methods may find their reputations being algorithmically defined without their participation. This paper explores how mining companies can proactively engineer their reputations in the age of AI.

Jan 1, 2026

Lime production is the largest single chemical use for limestone and dolomite. The term “lime” in this review refers to high-calcium and dolomitic quicklime, their hydroxide forms and dead-burned dolomite. This review is restricted to a discussion of the U.S. lime industry. Production and consumption In 2004, according to preliminary data, U.S. lime production was about 20.1 Mt (22.1 million st), an increase of 900 kt (990,000 st) compared with 2003. Production in2004 was valued at about $1.4 billion. Commercial sales of lime totaled 18.6 Mt (20.5 million st) and captive production was 1.5 Mt (1.65 million st). Total U.S. consumption was about 20.2 Mt (22.2 million st). The majority of U.S. lime trade was with Canada.

Jan 1, 2005

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By H. S. Price

This report discusses the development of a mathematical model that describes the flow of methane only and methane and water in a coal bed during mining operations. Because of the complex geometry, boundary conditions and fluid properties, the model is based on a numerical solution to the equations describing flow. The goals for the development of this model and requirements to which it complies are for the most part expressly stated in Request for Proposal No. 50110752. In addition to the capabilities specified under the scope of work the model can handle an anisotropic porous medium and a source term has been added which will simulate, somewhat, the effects of desorption. This term will be pressure dependent. The effect of time on such a term is only taken care of in the change of pressure with time. This source term will have the dimensions of Mcf/day/Mcf pore volume. It will be a part of the input data to be supplied by the user and will be entered as a table of rates versus pressure. These models consider the fracture system as the main porosity. All computed results pertain to the fractures. The source term mentioned above represents the flow from the matrix porosity into the fracture. Such flow should be small compared with the flow between fractures since these models handle only one porosity structure system.

Jan 1, 2012

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By Thomas M. Barczak

This report examines practical considerations in longwall support selection that have evolved from Bureau of Mines ground control research. The scope of discussion includes trends in support selection, analysis of shield designs, performance testing, and an examination of support and strata interaction theories and their relevance to in situ support loading. Application recommendations are made for two-leg shields. four-leg shields, and chock-shields. Two-leg shields account for 67 pct of the current active longwall installations and are used in a variety of applications. Automated control systems are likely to continue to grow in utilization. The next major change in shield design is likely to be the application of wider supports. The most effective method of performance testing longwall shields is by controlled displacement of the canopy relative to the base. Controlled force application does not control the load transfer through the shield and may not produce maximum loading in all support components. Theories of estimating support capacity based upon a detached roof block that must be maintained in equilibrium by the powered support are being challenged by concepts based upon the equivalent stiffness of the total ground supporting system.

Jan 1, 1990

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

By Forrest T. Moyer

The overall injury experience, excluding officeworkers, at metal mines and mills during the period 1961-63, reported by operators, was 174 fatal and 11,357 nonfatal disabling work injuries during an aggregate worktime of 451 million man-hours. These injuries occurred at a frequency rate of 25.55 per million man-hours, comprising 0.39 for the fatal and 25.17 for the nonfatal injuries. The combined severity rate of the disabilities was 3,779 days lost or charged per million man- hours, consisting of 2,314 for the fatal and 1,465 for the nonfatal injuries. The average severity of all disabilities during 1961-63, was 148 days per injury. The number of days lost and/or charged, ex- cluding officeworkers, at metal mines and mills during the period 1961-63, was 1,440,000 days charged to fatal injuries and 661,290 days lost from nonfatal injuries. An average of 70,966 men were at work daily. The outstanding cause for fatal injuries was the fall of rock or ore from the back, while most of the nonfatal injuries were caused by handling materials, slips or falls of persons, machinery, falls of rock or ore from back and side, and haulage. Injury experience at primary nonferrous smelters, refineries, and reduction plants during 1961-63, excluding officeworkers, was 23 fatal and 3,214 nonfatal disabling injuries during a total work- time of 277 million man-hours. The injuries occurred at frequency rates of 0.08 per million man-hours for the fatalities and 11.61 for the nonfatal disabilities. The severity rate for all injuries of 1,085 days lost or charged per million man-hours comprised 498 for fatal and 587 for nonfatal injuries. The number of days lost, excluding officeworkers, at primary nonferrous smelters, refineries, and reduction plants during 1961-63 was 138,000 from fatal injuries and 162,385 from nonfatal injuries, An average of 34,938 men were at work daily an active plant days during the three year period. The injury experience for officeworkers at metal mines and mills during the period 1961-63 was 20 nonfatal disabling work injuries, (there were no fatal injuries reported), during an aggregate work-time of 28,694,244 man-hours. These injuries occurred at a frequency rate of 0.70 per million man-hours. There were no fatal injuries reported for officeworkers at non-ferrous smelters, refineries, and reduction plants during 1961-63, but seven nonfatal injuries were reported during an aggregate work-time of 30,814,772 man-hours. The frequency rate for these injuries was 0.23 per million man-hours for this period.

Jan 1, 1967

By Allan E. Martin

As part of a comprehensive investigation of tae mechanism of desulfurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of :lines, in cooperation with the Institute of Technology., University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FeXCay)S and (MnxCay)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

This evening I would like to speak about men for the mineral industry.It is trite to say that the mining industry is expanding rapidly and that technically trained men are in short supply. How short is difficult to assess and impossible to quantify.The industry has been traditionally managed by technically trained men experienced in the ways of their fellow men. Let us start with the assumption that men with this training and experience are essential to management of mining and metallurgical enterprises.I suggest that we do this as it avoids argument with those who are beginning to suggest that such men are not so important as they used to be; who are suggesting that the latest sophisticated business management schools can produce managers who can straight out of school join the upper echelons of an organization and successfully manage it by the use of modern systems and techniques without the need to rub shoulders with men of all callings and get their hands dirty in the process.This kind of thinking brings to mind the modern cargo ship which is equipped with all the latest gadgets of science. It can find its way from Sydney to Auckland with no one in the engine room and the man on the bridge spending most of his time writing to his wife or reading the latest novel.How often do we read of this ship being tied up in Sydney because the crew sympathizes with the cook who has been slighted by some uncomplimentary remark about his toheroa soup? Here is a pieceof sophisticated machinery stopped through no technical fault, but held up by the whim of man. The understanding of man by man can spell the success or failure of any endeavour. A single man can leadan organization to the pinnacles of success, or doom it to utter failure in spite of modern systems and techniques.So let us start from the point that people matter.Through the years our Institute has been fortunate in having many members who have felt strongly...

Jan 1, 1970

By L. L. Hirst

In 1944, the 78th congress of the United States enacted Public Law 290, which directed the Secretary of the Interior, acting through the Bureau of Mines, to furnish industry with basic information and cost data for the development of a synthetic liquid fuels industry. Recently published information with respect to the cost of synthetic liquid fuels processes indicates a wide variation in estimated results. To clarify the results and inconsistencies for the hydrogenation of coal, the Bureau of Mines has prepared preliminary designs and calculated detailed investment costs from which the operating costs to produce 30,000 barrels per day of liquid products, mainly gasoline, by coal hydrogenation were obtained.

Jan 1, 1949