Search Documents

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

Jan 1, 1994

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

Geotechnical input is interwoven into the mining process at George Fisher South Mine from the planning and design of working areas to the closure of worked out areas and maintenance of life of mine and long term excavations. The methodology used consists of a mixture of application of established theoretical principles and guidelines derived from successful historical experience. In the development stage, including long term infrastructure excavations, the process takes into account the expected life of the excavation, usage and expected stress changes during its life span. On the stoping stage, the design process takes into account the local rock mass conditions, geological structure setting and previous experience in a particular orebody. Due to the high variation in age of currently used excavations, a rolling monitoring and risk assessment process for long term and life of mine excavations and infrastructure is maintained. This paper has as an output the process that must be followed to ensure an excavation on the highly dynamic mining environment at George Fisher South Mine is blasted and maintained in compliance with applicably commonly accepted safety and industry requirements.

Nov 25, 2010

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By Phil Jones

"Dilution — planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a sixmonth period in fiscal year 2018 (FY18) that established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned versus actual toe data. These were rig alignment error, collar location change/ error and in-hole deviation.The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimizer system). The trials were undertaken in the same environment: the Cracow gold mine, an operating underground mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160 percent.The increased accuracy reduced stope dilution by reducing over-break of subgrade ore. The new technology was implemented at Cracow during the latter half of 2018. Despite utilizing the new technology for just six months of the year, the mine recorded a 5 percent overall reduction in dilution for the full year compared to the previous year (FY17); from 22 percent down to 17 percent (a net decrease of 22.7 percent). Mine management attribute a significant proportion of this reduction to the new technology, along with sequencing and planning improvements. This opinion is backed by detailed stope reconciliation data taken during the trial from 28 stopes — representing 20 percent of the total tonnes mined during FY18. The data identified that stopes drilled using the new technology recorded 62.6 percent less average dilution."

May 1, 2019

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By D S. Clarke, K B. Sporli

The Thames Goldfi.eld has been a major gold resource in the west of the Coromandel Peninsula, New Zealand, with the Waiotahi quartz vein system forming a large part of the field. Mineralisation is hosted by hydrothermally altered Miocene andesitic volcanic rocks. Both massive columnar-jointed and fragmental volcanic rocks are present. The vein system is dominated by the steeply dipping NE striking Waiotahi-Cambria vein, and associated splays. Hydrothermal alteration increases in intensity from isolated blocks of propylitic altered andesitic material, into the intensely clay altered equivalent. Low rank propylitic alteration is typified by chlorite, calcite and pyrite, with local illite or epidote. Clay alteration is characterised by illite, quartz, kaolinite and pyrite. While broadly forming halos around veining, intense clay alteration also occurs in strongly jointed portions of the hostrock.   Vein textures and the intense illitic clay alteration at Thames are similar to those in some of the other epithermal gold deposits of the Coromandel Volcanic zone, and in deposits of the Philippines, all related to andesitic terranes. Possible causes for textures and alteration being different in these deposits from the more classic Quartz-Adularia-Illite type epithermal systems may be that cooling/mixing rather than boiling dominates fluid evolution. Kaolinite may be also be a product of either of these different fluid types, or has resulted from overprinting of an illitic assemblage by downward percolation of acidic fluid.

Jan 1, 1991

By J. Botin

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require more complex risk evaluation models that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, and production rates, among many other). In this context, real option valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed that successfully quantifies the risk associated with dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mine project. Keywords real options, risk management, risk quantification, dilution, minine planning.

Jul 1, 2013

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012