Search Documents

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By Yoshinao Kobayashi

he removal of oxygen from titanium and zirconium is important for use in application because it significantly affects the mechanical and physical properties such as ductility and toughness. However, thermodynamic properties of oxygen in molten titanium and zirconium have not been clarified and the effective deoxidation process of molten titanium and zirconium has not been established. In this study, the standard Gibbs energy of reaction of oxygen and yttrium in molten titanium and zirconium have been measured by a chemical equilibrium technique. Molten titanium, zirconium, and their alloys with aluminum were equilibrated with a Y2O3, A12O3, or Zr02 pellet in a cold crucible. The results are summarized as follows:

Jan 1, 2000

By Gus Van Weert

Hydrometallurgical oxidation of sulphides is capital and energy intensive, with autoclave and bio-technology competing for lowest overall cost status. The use of surface aerators instead of stirred tank reactors could provide lower costs for bio-oxidation of concentrates. With this in mind, the Delft Inclined Plate reactor was designed with inclined plates above a settler shaped reactor to continuously return slurry from the lowest point in the settler to the surface of the liquid. The multiplate superstructure overcomes the scale-up restriction of the standard circular surface aeration patterns. DIP aerator energy and volume requirements for oxygen transfer from air will be presented in terms of kg O2/kWh and kg O2/m3/h transferred as a function of wt % sand in the slurry and compared to stirred tank performance. Scale up from the 4 m3 pilot unit will be discussed.

Jan 1, 1996

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

By Christian Wögerer

For material or process development as well as for quality checking of materials, thermal diffusivity measurement may be the tool of choice in many applications. Especially if diffusivity is measured locally resolved, a lot of information can be read out of such a ?diffusivity image?. This paper explains the method to measure coplanar specimen like plates and lists some interpretations of diffusivity images, like inhomogeneity of sintered materials, structural voids or inclusions. Diffusivity is a material property, describing transportation of heat in solids in spatial and temporal terms. With thermo cameras it is possible, to measure diffusivity of larger areas simultaneously. The result is an area of diffusivity values that may be plotted or displayed like an image. Locations with lower diffusivity values could be caused by the presents of structural differences in the material, by decomposition of the material components or by inclusions of other material like air.

Jan 1, 2009

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By Michael A. Lllga

Electrically Switched Ion Exchange (ESIX) is an approach for ion separation that combines Ion exchange (IX) and electrochemistry by utilizing electro active IX films to provide a selective, reversible, and economical separation method that greatly reduces secondary waste generation compared with conventional ion exchange. Studies on the development of films with improved stability and capacity and their use in continuous flow systems for ion separations will be. reported. Both technical and economic evaluations demonstrate ,the viability of once-through or batch recycle waste processing with ESIX.

Jan 1, 1999

By Khalid Hattar, Alexander McGinnis, Buchheitm Thomas, Paul Kotula, Luke Brewer

"Understanding the effects of extensive radiation damage in structural metals provides necessary insight for predicting the performance of those metals considered for application in the extreme radiation environment. Predicting mechanical performance after long term radiation exposure is of great importance to extending the life of current nuclear reactors and for developing future materials for the next generation of reactors. A combination of finite element modeling, nanoindentation, and TEM characterization were used to rapidly determine the microstructure and mechanical properties influences of ion irradiation on a standard 3 l 6L stainless steel sample. The results of this study found that ion irradiation and small scale mechanical property testing can be used to characterize extensive levels of radiation damage structure, only when significant consideration is given to ion irradiation depth, surface roughness and polishing condition, the irradiation temperature, and many other experimental parameters.IntroductionFor either the success of next generation nuclear reactors or the extension of current nuclear reactors significantly beyond their designed lifetimes, research is needed into the degradation of the microstructure and mechanical properties governing the performance of the reactor alloys exposed to extreme environments. Although the exact dose and temperature of these nuclear reactor plans may vary, the cladding and other structural components will be exposed to greater dose and at elevated temperatures. To acco=odate these severe exposures, established cladding materials are being testing to longer exposure and new alloy compositions are being considered. [1-3] For neutron test facilities to reach 100 dpa level, exposure times often span several years, significantly limiting the down-select process of potential new materials for extreme radiation environments. Ion irradiation has been used as a technique to provide a look at the effect of irradiation damage on materials in a significantly shorter time frame. Previous work using proton irradiation provides a deep, broad, and relatively uniform defect profile compared to heavy ion irradiation; however, using this type of radiation still requires weeks to months to reach the 100 dpa level. [4] In this research, we investigated the feasibility of using heavy ion (nickel) irradiation and small scale mechanical testing to provide in a few days a first order screening technique for potential alloys that are being considered for advanced testing."

Jan 1, 2012

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By Niko Hellstén

To capture efficiently the valuable trace metals from nickel slag using electric furnace, it is important to study their distributions between the slag and metallic phases in the furnace. It is impossible to calculate accurately these distributions without experimental measurements. Therefore, in this work, selected trace metal distributions and phase equilibria between K2O containing iron-silicate slags and a metallic Ni-Fe-Cu alloy in nickel slag cleaning furnace conditions were studied. The experimental method developed and applied during the work, involved a modified quenching technique that included equilibration of the samples in semi-sealed quartz ampoules in an inert atmosphere and metallic Fe saturation. The use of the semi-sealed quartz ampoule prevents the escape of volatile elements from the sample during equilibration. Chemical compositions of the phases and the trace elements were analysed by EPMA. From the measured compositions, the trace metal distribution coefficients between the molten Ni-Fe-Cu alloy and slag were calculated.

By Zhaohui Xie, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

A high carbon low-grade gold ore, in which gold mainly occurs in carbonaceous matters, is a typical refractory gold ore whose conventional cyanide leaching extraction is only 12.9 %. In this paper, by the process of flotation-roasting-leaching, gold was effectively enriched and extracted. The flotation results showed that the enrichment ratio of gold was relevant to that of carbon, indicating that gold occurred in close association with carbon. A concentrate containing gold 7.26 g/t and carbon 12.37 % was obtained, with gold recovery 83.10 % and carbon recovery 90.24 %. Subsequently, the roasting of flotation concentrate favorably made the removal rates of carbon and sulfur reach 99.81% and 98.79%, respectively. After roasting, the gold in the roasted product was further enriched to 29.70 g/t and the optimal gold cyanide leaching extraction reached 93.66%.

Jan 1, 2015

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Alan P. Prosser

The heap leaching of gold ores by cyanide solution was simulated by computer program. The program uses only basic m1neralogical and chemical data; no process testwork data, such as column leach results, are required. The simulation can be used to forecast the consequences of various changes before and during the testwork, design and operation stages of a particular ore-process system. Also, data about the state of different parts of the heap at various times help create an understanding of what is happening. The effects of mineralogical and process variables on the overall performance of the ?heap leaching process are illustrated. Comparisons are made to column leach tests and production data. The potential of the simulation strategy is discussed for making better use of operating experience and for suggesting specific research objectives. It has become clear that more attention should be paid to other metals that dissolve in the solution.

Jan 1, 1989

By Giuseppe Bonifazi

Minerographic and petrochemical research was carried out on crude ore samples from the complex polymetallic Zn-Cu-Pb sulfide ores of , Sotiel in Huelva province west of Seville, Spain. A computerized image analysis system was used to define the structural and textural characteristics of the ore to obtain information on the degree of liberation of the different minerals (i.e. pyrite, sphalerite, galena, chalcopyrite). Techniques of digital multispectral image processing of reflected light microscopy images were used. Particular structures were identified by means of mineral associations and numerically quantified to obtain useful information for designing beneficiation processes.

Jan 1, 1991

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By F. Garcia-Carcedo

This research aimed to develop a clean technology for the production of ZnO from residues generated by the steel making industry. Scientific and technologic parameters were both investigated in order to define an industrial methodology allowing the integral recycling of EAF dusts. A reengineering of the Waelz process was perform,~d, aiming to produce a clean fraction of ZnO, fluorine free, as well as a slag enriched in metallic iron, which can be recycled in electric arc furnaces. The technical conditions used to produce the ultra pure fraction of ZnO are described. The magnetic separation of the EAF dust allowing the production of a phase high in iron and recyclable to the electric arc furnace is also discussed. Thermodynamic of the volatilization of all the elements contained in the EAF dust was performed in order to better control the thermal process in the rotary kiln. Tests were run using different reducing agents, weakly or highly reactive, aiming to determine their specific efficiency.

Jan 1, 2000

By Bradford C. Wesstrom

The extraction of metals from Copper Refinery Slimes may involve many different processes. This paper describes the use of pressure leaching for decopperizing of copper refinery slimes at the El Paso Refinery. Process equipment will be described, along with the process chemistry, unit operations and unit processes associated with the decopperizing process. Copper contained in the raw slimes ranges from 15-35%. After autoclaving less than 1 % copper remains.

Jan 1, 2000