Search Documents

By Ray Y. Lin

Chemical vapor deposition of tungsten carbide on the surface of steel has been investigated at temperatures between 400 and 550C in an atmosphere containing tungsten hexafluoride, hydrogen and benzene. The tungsten fluoride flow rate was maintained at 20 ml/min. The hydrogen flow rate was at 100 ml/min. The benzene concentration varied from 1.15 to 5.56% in the reaction gas. It was observed that the higher the temperature, the faster the deposition rate for tungsten carbide. But the dependence of the deposition rate on the benzene concentration was not systematic. From the x-ray diffraction analysis, it was observed that W, W2C and WC are all presented in the coating. The amount of each phase presented in the coating depends on the temperature and, to a less extent, on the benzene concentration. The microhardness measurement has also been done for all CVD carbide coatings obtained in this study.

Jan 1, 1992

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By Corby G. Anderson

For over a century, the Sunshine Mine in Idaho has been a major producer of silver. An estimated 335,000,000 troy ounces of silver has been mined. This has established the Sunshine Mine as the largest single source of silver in the world. Because the dominant silver containing mineral is tetrahedrite, a copper and antimony sulfide, normal metallurgical treatments to recover the precious metal are not practical. Thus, over the course of the company's history, novel, hydrometallurgical technologies have been developed on-site to handle complex, precious metal containing materials. Recently, the use of Sunshine technology has been extended to the recycle of secondary materials. As well, the use of Sunshine technology by other organizations for treatment of both primary and secondary feedstocks containing precious and base metals is an area of growing interest. This paper will provide an overview of Sunshine hydrometallurgical technologies including the applicability of Sunshine technology to the recycling of precious and base metals.

Jan 1, 1995

By T. Kamata, S. Takemoto, H. Takeuchi, M. Takayanagi, Y. Akahori, I. Jimbo

"A cooperative research work on the silver recycling process is underway between Matsuda Sangyo Co., Ltd. and Tokai University in Japan. Silver wastes treated here are mainly from photograph industries where the concentration of minor element is steadily increasing in the recent years. The waste materials are concentrated and the impurities are removed by evaporation and slagging. In this paper, the industrial practice of wastes treatment is introduced and the result of the laboratory studies on the removal of antimony and tin from the binary and ternary alloys will be discussed. Characteristics in the behavior of antimony and tin during the process are also discussed with the observation of practical operation.1. IntroductionPrecious metals such as gold and silver primarily come from mining practice and the byproduct in copper smelting. However, the recycled amount of these precious metals have been increased 1 along with the environmental restriction and the widely accepted idea of saving resources on the earth in the recent years.· Though the recycle process of precious metals are comparatively simple from other metals refining, the process has been getting more complicated as wastes treatment has to deal with more impurity elements which are intentionally added to the products. Among these additives, antimony is used in the film materials in the photography industries to suppress its inflammability. Tin is another concern ,that is also coming from photography wastes; These minor elements have become problematic during the recycle.The removal of these minor elements has been in operation at Matsuda through a traditional oxidation refinement process using a reverberatory furnace. However, the complexity of the charge makes the recycle process more tedious and troublesome. In order to investigate the minor element behavior in the complicated materials system during the silver recycling processes, a cooperative research work is undertaken between Matsuda Sangyo Co., Ltd. and Takai University in Japan. Silver wastes treated here are mainly discharged from photograph industries where the minor element contents such as antimony, tin and bismuth in those wastes are steadily increasing in the recent years. The liquid wastes containing silver are concentrated and then treated pyrometallurgically with solid wastes from other sources, where the impurities are removed ·by evaporation and slagging. The purpose of this study is to investigate detailed behavior of impurity elements in the silver. containing systems."

Jan 1, 2000

By Mikiya Tanaka, Mikio Kobayashi, Kazuya Koyama, Yoshihiro Nishisu

Preparation of multicomponent powders are very useful and important for producing the materials with complicated and homogeneous structure. Therefore multicomponent powders have a lot of attention in the field of advanced value-added materials. The aqueous processing in hydrometallurgy has a broad potential for producing multicomponent homogeneous precipitates. Furthermore the aqueous processing has a future potential for integrating the separation, precipitation and synthesis processes. In this presentation the precipitation from homogeneous solution including rare-earths and/or common metals is presented. These precipitates probably consist of almost monodispersed, multicomponent and spherical particles by precisely controlling several reaction factors, reaction temperature, concentrations of starting materials, pH and so on. The separation of the nucleation stage and the growth stage of the particles is very important and how to control the reaction factors to realize enough separation is discussed. In this presentation the systems of Y-Eu-0, Y-Fe-0 and Y-Al-0 are mainly presented. In addition the precipitation-stripping method from organic phase is presented focusing the synthesis of multicomponent powders of Ni-La-0 system. These precipitates have multicomponents homogeneously and so they are converted to multicomponent ceramic powders by calcination. They are important compounds as phosphor, opto-magnetic materials, optical materials, hydrogen storage alloy or as the related precursors. In this presentation some characterization of these particulate materials is included.

Jan 1, 1998

By Katsukiyo Marukawa, Manabu Iguchi, Sigeta Hara, Shinichiro Yokoya, Sigeo Takagi

"A numerical analysis and water model study of the mold region of a continuous casting apparatus was performed with a novel injection concept using swirling flow in the pouring tube, to control the heat and mass transfer in the continuous casting mold.As a result, the following results were found:1) By changing swirl strength, it is easy to control the flow pattern as well as the direction of the flow.2) Uniform velocity distribution can be obtained within a very short distance from the outlet of the nozzle.3) Heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl.4) Swirl helps the superheat in the melt dissipate.S) Penetration depth of nozzle outlet flow is decreased remarkably by the application of swirling.6) For the case without swirl, the peak of the flow moves near the mold-wall with flowing down from the outlet of the nozzle due to the Coanda-effect. On the other hand, peak of the flow moves near the mold axis with flowing down from the nozzle-outlet within considerable short distance, namely axi-symmetric velocity distribution can be obtained within very short distance from the nozzle-outlet.Those findings mentioned above are very useful to control the flow pattern in the billet and bloom continuous casters."

Jan 1, 2001

By Hwa-Soo Park, J. K. Yoon, Hoseok Nam

In a thin slab casting process, control of fluid flow in mold is particularly difficult due to the high casting speed and large aspect ratio of the mold and the understanding of the fluid flow motion as well as heat transfer in mold is regarded as the most important information because the melt delivery is directly related to the problems of shell growth nonuniformity, surface turbulence and mold powder entrapment. A mathematical model has been developed for the coupled analysis of fluid flow, heat transfer and solidification in funnel type mold using finite volume method based on a body fitted coordinate and the characteristics of the transport phenomena in the mold of thin slab caster were analyzed by numerical simulation. As a result of simulation, the basic flow pattern is characterized as four large recirculations and two small eddies near the narrow faces of mold, which is somewhat different from that of parallel type mold or other conventional slab caster. The heat transfer model accurately predicted the mold positions susceptible to cracking as a result of thermal stress and the predicted shell thickness shows good agreements with the measured shell thickness on breakout products. We also investigated the influences of some operation parameters such as casting speed, nozzle type, submerging depth and mold material on fluid flow, heat transfer and distribution of solidifying shell and various information for the determination of optimal operating conditions were obtained.

Jan 1, 2000

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

By Zhang Chuanfu

The fibrous nickel oxide powder was prepared by the method of chemical precipitation and pyrolysis, that is, the NiO precursor was firstly precipitated from nickel ions solution with addition of oxalate salt and then the final NiO powder was obtained by pyrolysis of the prucursor. The effects of the pH, reaction temperature, reactant concentration, addition of surfactant on the morphology of the precursor particles were investigated. The influences of the various conditions, including the temperature and time, the air flow and the speed of the temperature increase on the morphology, average size and specific surface area of the NiO particles were also addressed. The fibrous NiO particles with IOO~ 120 in axis/diameter ratio and 5.5 m2/g of the specific surface area may be produced under certain operation conditions by this process.

Jan 1, 2003

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By Brommerm Tracey, Britt Elin Gihleengen, Elsa Olivetti, Hans Ole Riddervold, Randolph Kirchain, Geir Øyen

"Compositional uncertainty in secondary materials and variable processing conditions inhibits secondary material utilization in the production of aluminum alloys. Efforts to implement optimization models that direct batch planning have limited industrial presence due to factors such as the insensitivity of these optimization models to dynamic plant circumstances. This paper describes a chance constrained model formulation that generates lower cost, robust batch plans with significant flexibility towards changes in processing conditions. The principal attribute of the chance constrained formulation is its inherent mitigation of risk by diversifying the batch plan. This paper compares aluminum remelter batch planning using the chance constrained formulation with a traditional deterministic model and a manual batch planner. With the expectation that volatile material prices, restricted scrap material availability, and pressure by consumers and legislation for increased recycled raw material input will continue in the future, batch planning tools that inherently diversify a production portfolio will become increasingly advantageous for industrial aluminum remelters.IntroductionAluminum remelters must develop strategies to incorporate lower cost secondary materials into finished alloys to remain competitive amidst increasingly demanding market and regulatory conditions. Determining the optimal combination of incoming raw materials to produce an alloy that meets compositional specifications presents remelters with a complex problem that has driven the development of computational tools commonly referred to as batch planning or blending algorithms. The ubiquity of the ingredient or raw material blending problem in production has motivated ongoing development of batch planning algorithms since the classic nut-mix problem in the 1950's [1]. The most common model formulation for industrial aluminum remelters are deterministic, linear optimization programs [2]. These blending problems determine the optimal combination of raw materials by minimizing cost subject to constraints around demand, availability, and compositional specification. Despite extensive research and moderate computational requirements, batch planning algorithms are inconsistently used in industry. Insufficient incorporation of the complexity of real world remelting conditions into these models provides an obstacle for their implementation [3]. For example, many batch planning algorithms do not explicitly incorporate the impact of compositional variation of the raw materials on overall batch cost. Additionally, they do not allow for endogenous specification of tolerance to error in batch planning, so provide little flexibility where a batch planner would like to incorporate materials of greater uncertainty. Incomplete accounting for quality variability undervalues secondary materials leading to overly conservative use [ 4, 5]."

Jan 1, 2011

By David S. Dolan

To beat capital costs of US$10 per pound of installed capacity has appeared as a major hurdle for the "third generation laterite nickel plants. Forecast costs are escalating. Where can savings come from? Ore beneficiation can reduce the tonnage rate to be processed. High pressure acid leach options include the use of indirect slurry heating and higher operating temperatures to reduce flow rates and residence time. Progress has been reported in atmospheric leaching. High counter current decantation circuit settling rates and high underflow densities reduce CCD costs. Metal recovery options include direct from leach solution to metal production, as used by Bulong and espoused by Goro, and indirect recovery as used by Moa Bay, Murrin Murrin and Cawse. Plant location impacts on the costs of tailings disposal, power and energy costs, supply of consumables and labour costs, among others. Final nickel and cobalt metal production routes are electrowinning, hydrogen reduction or some innovative routes being proposed for Goro. This paper reviews the status in these developments, with particular reference to equipment and processes that offer lower capital costs. Keywords: Laterite, Nickel, Plant, Capital Cost

Jan 1, 2004