Search Documents

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.

By Hongxu Li, Pu Liu, Hao Bai, Daqiang Cang, Lihua Zhao

"Coal, as the main energy in ferrous metallurgy, is consumed on a large scale and great amount of CO2 is emitted likewise. In this paper, a model, based on carbon balance, was developed for CO2 emission analysis, with data obtained from a typical integrated steelworks in China. The result shows that, CO2 emissions increase almost constantly with the growth of steel production. However, coals of different classes and product variety in the steelworks exerted an influence on CO2 emissions. Furthermore, three scenarios, including natural gas instead of coal for power generation, EAF process partly replacing integrated steelmaking, and feasible techniques applied to achieve lowest process energy consumption (FLPEC), were assumed to seek possible ways of carbon emission reduction. The result proves that the second scenario is most effective. If 40% of the steel product could be from EAF process, CO2 emissions would be reduced by 45.07%.IntroductionGlobal warming has become a global environmental problem, which is generally caused by excessive emission of greenhouse gases, such as CO2, generated from human activities and industrial processes. It is estimated that about 7% of global CO2 emissions was from iron and steel industry. Further, if the ore and coal’s mining and transportation are included, the CO2 emissions would reach 10%[1]. In general, the relationship between energy saving and CO2 emission reduction is positive correlation. However, in iron and steel enterprises, due to different types of energy resources like coal, heavy oil, natural gas, the consumption of which will generate different amount of CO2, are used, different energy consumption structure in iron and steel enterprises will lead to difference of CO2 emissions.In order to assess the CO2 emission reduction potential of China’s steel industry, Ke Wang etc.[2] developed a model using LEAP software to generate 3 different CO2 emission scenarios for the industry from 2000 to 2030. LEAP is a scenario-based software tool for integrated energy-environment and greenhouse gas mitigation analysis. The amount of CO2 emissions was obtained by the following equation:"

Jan 1, 2011

By Hitoshi Iijima, Fumitaka Tsukihashi

"Fine powder of tantalum is used as materials of electric condenser. It is important to control the distribution of particle diameter of tantalum fine powders for the commercial use. In this study, fine powders of tantalum were produced by reducing tantalum chloride vapor with hydrogen gas at 1673 and 1773K. The tantalum chloride vapor was reduced with hydrogen and the produced fine particles of tantalum were collected to observe the distribution of particle diameter. The effects of reaction temperature, partial pressure of hydrogen gas and vaporization temperature of tantalum chloride on the distribution of particle diameter and reaction efficiency of reduction were determined. The mechanism of reduction reaction of tantalum was discussed.IntroductionThe ultra fine powder shows various different physical properties from that of bulk materials. Therefore, the application of ultra fine powder to various fields such as magnetic material, electric material, catalyst, etc is anticipated. The control of shape of powder, size distribution, property of agglomeration, purity is required for the practical use of ultra fine powder. Although the ultra fine powders of ceramics are produced by various methods, the ultra fine powder of metals are produced by the evaporation in gas atmosphere, plasma evaporation process, chemical vapor deposition process, and reduction and precipitation in liquid phase depending on the metal and productivity. The chemical vapor deposition process has features that pure metal powder can be obtained and the control of the distribution of powder size is easy. [1,2,3,4,5]"

Jan 1, 2000

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

By Jinxia Nie, Yunnen Chen, Dachao Zhang

"Rare earth resources are strategic and non-renewable resources. But disordered exploitation on rare earth metals leads to resources waste, environmental pollution and ecosystem destroyed. In this paper, soil collected from garden was cultured in thermostated incubator. Adding exogenous rare earth to the soil and the effects of recombination action of rare earth lanthanum, cerium and yttrium on soil enzymatic activities were studied. The results showed that single metal La and Ce can increase urease activity, but Y inhibits its. Coexist La/Y or La/Ce in soil inhibit the urease activity, coexist Y /Ce or coexist three metals promote its. Single metal La, Y and Ce can promote catalase activity, and that of coexist three metals. Pairwise coexist La, Y, Ce in soil inhibit catalase activity. With certain concentration of rare earth recombination action, urease activity in soil has been very significant direct proportion to ionic impulse, but catalase activity been insignificant inverse proportion to its.1. IntroductionThe increase of rare earth element content due to anthropogenic inputs frequently takes place in agro-industrial areas, leading to soil pollution episodes that may cause serious environmental problems because of their potential toxicity to microorganisms, plants, animals and human beings [ 1]. China is abundant in lanthanides resources. Rare earth metals are used in many frontier technologies such as photic devices, magnetic materials, and fine ceramics, and the amount of the rare earth metals used in these industries has been increasing. In addition to their use in industry, rare earth metals are more widely applied to cropland as microelement fertilizers due to their ability to promote growth and productivity of some crops [2]. As a result, more and more rare earth metals are moving into the ecosystems. While a permanent contamination of soils results in populations of micro-organisms with high resistance to rare earth metals, a short-term burden of contaminants at high concentrations could exert inhibitory effects on microbial carbon [3]. They accumulate in soils, bioaccumulate in crops, and enter the food chain, causing a potential problem of rare earth metals environmental pollution in China [4]. This contamination may also severely influence organisms and soil activities [5]."

Jan 1, 2011

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By Axel Hoppe

Although Tantalum is not usually regarded as a precious metal, its pricing structure is very similar to that of Silver. Different from precious metals, Tantalum has only industrial applications and its use is about 1000 metric tons per year. The intrinsic value of Tantalum already in .the past was a driving force for its recycling. Based on these facts the Tantalum industry world-wide is approaching the closed-loop concept of its recycling. A detailed material flow of Tantalum processing as well as recovery of residues and used products will be discussed.

Jan 1, 1995

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By N. Tsuneyama

Sumitomo Metal Mining Company has been operating Waelz Kiln at the Shisaka Works for 12 years to recover zinc and lead from electric arc furnace (EAF) dust. To increase the capacity and cut down the operating cost, some improvements have been carried out resulting in the capacity of 60,000 t/ y of EAF dust as compared with 32,000 t/ y in 1977. The current capacity is equivalent to 20% or EAF dust generated in Japan. The number of workers has been decreased by the introduction of an automatic control system, and the productivity per worker is now twice as much as 10 years ago. This paper will describe the progress of the operation at the Shisaka Works after the previous? paper reported in "Zinc' 8 5? and summarize the status or EAF dust recycle in Japan.

Jan 1, 1990

By Fangqing Yin, Qingyu Deng, Zhengfeng Qu, Mengjun Hu, Meilong Hu

Titanium bearing blast furnace slag, which contains 20%-30% TiO2, is a valuable secondary titanium resource. Based on the thermodynamics calculation effect of the temperature on the reduction of the slag in vacuum were studied at certain vacuum degrees. The results show that magnesium vapor and silicon monoxide vapor can be obtained at the condition of high temperature and low pressure. The purity of TiC increases with temperature increasing. When the temperature arrives at 1623K TiC can be obtained besides the reductant carbon. XRD result of the powder collected from the furnace cover show that magnesium and silicon in the titanium bearing BF slag leave the slag system during carbothermal reduction in vacuum. From the above it can be concluded that TiC can be obtained from the titanium bearing BF slag and silicon and titanium in the slag can be separated by carbothermal reduction in vacuum and acid leaching.

Jan 1, 2016

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

Kosaka Smelter & Refinery has a history of more than a century as a metallurgical department belonging to Kosaka mine. It has treated for a long time the "Black Ore" or the complicated concentrates dressed from it. The "Black Ore" is composed of black sulfides. It contains not only valuable metals such as gold, silver, copper, lead and zinc but also some impurities like arsenic, antimony and bismuth. With the development of Kosaka's floatation technology, five kinds of concentrates (copper, zinc, lead, pyrite and barite) have been separated from the "Black Ore" but the separation was not complete and each concentrate contained some unfavorable impuritie. In 1980s the highly appreciated yen and the drop of the metals priees forced many domestic mines to close their operations. Since then Kosaka Smelter has changed its way of operation to a custom smelter. Now more than 95% of copper concentrates are imported to take advantage of this technology of "Black Ore" treatment. It mainly treats the raw materials that contain high gold and silver like the "Black Ore". Recently, Kosaka has been working on the recycling of the metals from the printed circuit board scraps and sludge which contain some precious metals. The volume of the recycled metal is continuously increasing.

Jan 1, 2003

By Y. Maeda

Kosaka Smelter is a copper smelter located at the nothern part of Japan? and has been treating. complex sulfide concentrates using flash smelting technology for a long time. The flash smelting technology has an advantage in the point of controllability of matte grade and heat balance in the reaction shaft. But the disadvantage of this process, is that the dust generation ratio is high compared with other smelting process such as injection smelting technology. This reason why is that the flash smelting process is the oxidation process for the fine sulfide concentrates applying flash reaction in the oxygen enriched stream In addition of this disadvantage, the sulfide concentrates contains much volatile impurities is resulted the dust; eneration ratio more. This paper outlines the recent improvement of the flash reaction in the furnace and the behavior of impurities in Kosaka Smelter.

Jan 1, 1998

By Shuqiang Guo, Dingsheng Tan, Weizhong Ding, Zunyu Hu

"The mixture of hydrochloric acid and magnesium chloride is a good lixiviant for leaching of laterite. The solution can enhance the leaching ability because of the proton activity deviated positively from ideal. Otherwise, the existence of magnesium chloride in the lixiviant affects the dissolution behavior of magnesia, which may be an advantage of the process with less hydrochloric acid consumption. An investigation of magnesia particle dissolved in strong hydrochloric acid solution has been conducted. Influences of concentration of the magnesium chloride and hydrochloric acid and temperature on magnesia dissolution were studied. The dissolution mechanism was also discussed in this paper.IntroductionThere has recently been much interest in the use of hydrochloric acid leaching processes for recovering metal from ores or secondary resources [l-41_ Compared with sulfuric acid, the use of hydrochloric acid as lixiviant offers significant advantages including faster leaching kinetics even at atmospheric conditions, higher leaching rate and greater solubility for most metal chlorides [5-61 .With the gradual decline of the nickel sulfide supply, the extraction of nickel from laterites has become increasingly attractive [7-s1. Nickel may be co=ercially recovered from laterites both by pyrometallurgical and hydrometallurgical processes. The drawbacks of pyrometallurgical processes include the requirement of high grade ores, substantial energy input and loss of cobalt bound within ores. The extraction of Ni from lower grade nickel laterites ores is suited by hydrometallurgical routes, which play an increasingly important role with depletion of higher grade deposits."

Jan 1, 2014

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Nobuo Kikumoto

Recently, the treatment of industrial waste materials has been a serious social problem here in Japan. Filling them in ponds is now strictly prohibited due to a limited land area and incineration method is also regulated as not to generate DXN. In these conditions, Onahama Smelter has begun to treat shredder dusts (SD) of car at reverberatory furnaces to recover various metals such as copper, gold, silver and palladium without generation of DXN. The total volume of these dusts is expected more than 1 million metric tonnes a year in Japan. Onahama Smelter is now planning to treat about 20% of them in the near future by using tonnage oxygen. In this paper, the heat balance, control method of DXN and treatment of these dusts in reverberatory furnaces are described. DXN : Dioxin (The generic term of PCDD and PCDF)

Jan 1, 2000