Search Documents

By J. K. Brimacombe, I. V. Samarasekera, B. G. Thomas

"Mathematical models have been developed for the processing of static cast steel ingots and are app1ied to investigate the mechanisms for the formation of panel cracks. Panel cracking is an intermittent but persistent defect that causes affected steel ingots to be scrapped. A two-dimensional, finite-element, heat-transfer model was formulated and employed to calculate the temperature distribution in both large and small steel ingots during the various processing stages from initial casting to the start of rolling, including solidification, cooling in the mold and in air, reheating in the soaking pit, and subsequent air cooling. The stress state in the ingot arising from the calculated temperature variations was then determined. This involved the development of a transient, elasto-visco-plastic, finite element, thermal stress model, including the effects of phase transformation volume changes and kinetics creep, and temperature-dependent, mechanical properties. The results of the mathematical model predictions of temperature and stress were then used to determine the mechanisms and to suggest solutions for two different types of panel crack formation. Mid-face panel cracks apparently form during air cooling when the mid-face surface temperature is between the Arl and 500~C. Off-corner panel cracks appear to initiate internally during the early stages of reheating but do not propagate to the surface until much later. IntroductionPanel crack formation in static-cast steel ingots is a defect that has been plaguing the steel industry for several decades. Although the problem is intermittent, it is also serious since affected ingots must be scrapped. Panel cracks are manifested as two distinct types of cracking problems. ""Mid-face"" panel cracks are found exclusively in small, 2 to 6 ton, medium carbon steel (0.3 to 0.7% C) ingots and usually exhibit a single, continuous, longitudinal crack down the center of one of the ingot faces as shown in Fig. l (l). ""Off-corner"" panel cracks often form roughly oval, discontinuous crack patterns on the wide faces of large, 20 to 30 ton ingots as seen in Fig. 2 (2). They affect only low carbon steels (0. l to 0.2% C) with high manganese content. Both defects affect only aluminum-treated steels and are caused by a combination of intermediate temperature ductility loss involving aluminum-nitride precipitation and thermal stress generation. The ductility problem has received a good deal of attention which was the subject of a recent review (3). The present study was undertaken to investigate the thermal stress aspects of the problem through the development of mathematical models of heat transfer and stress generation in static-cast steel ingots. The ultimate objective was to elucidate the mechanisms of formation for both types of panel crack and to evaluate possible solutions to the problem."

Jan 1, 1986

By John W. Pickens

The recycling of industrial wastes and by-products is an important component of ecologically responsible industrial management. Converting waste streams into value-added products or material and energy resources with a profit margin assures the continued viability and practice of recycling. The recycling of aluminum stands out as one of the best examples with major economic and environmental benefit. However, the benefits are compromised by landfilling of black dross and salt cake, waste streams produced from within the recycling process itself. This paper reviews Alumitech's strategy and progress in establishing a tertiary aluminum industry based on closed-loop recycling of black dross/saltcake; one which does not compete with the primary and secondary aluminum industries, but rather serves their needs to ensure the continued economic benefits of aluminum recycling and elimination of environmental liablJity associated with landfilling of black dross/saltcake. Alumitech has made significant progress toward that goal in operation of its new recycling facilities in Cleveland where recovered aluminum and nonmetallic residue from salt based drosses is being converted into commercial products, eliminating the landfilling of the greatest portion of dross/saltcake. The economic strategy for recycling saltcake and its progressive achievement is reviewed.

Jan 1, 2000

By Valeriano Antonio Corbellini, Marilda Macagnan, Rosana de Cassia de Souza Schneider, Tiago Bjerk, Mariela de Souza Vieira

The great potential of Brazil for the agricultural production makes our country a generator of agro industrial residues. In this context, the solid-state fermentation appears as a technology that shows alternative ways for those residues, adding values to these raw materials, through the production of substances of industrial interest, besides reducing the possible environmental problems. The main objective of this study was to apply the bovine fat residue associated to the garden grass for the fungal lipase production. Initially, 75 microbial cultures were isolated from garden grass samples after incubation of the mixture with bovine fat. From these cultures were selected the filamentous fungi, whose lipase production abilities were evaluated. The isolation and the selection were accomplished by using a differential culture medium containing Tween 80 as inducer substrate of lipase production. The colonies with lipolytic potential were detected by the presence of white precipitation haloes on the agar. With agro industrial residues the best lipase producer fungus was identified as Penicillium sp in 6 days of solid state fermentation. The crude enzyme obtained was tested in transesterification process for the biodiesel production.

Jan 1, 2008

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Kensuke Sassa, Shigeo Asai, Norihisa Waki

"A new method for separating inclusions from a molten metal using a high magnetic field has been proposed. The principle of this method based on the magnetization force has been confirmed in experiments of separating intermetallic compounds imitating inclusions from molten Al-Si-Mn-Fe and Al-Si alloys. In order to measure a magnetic susceptibility, the Gouy's method has been so modified by using a super-conducting magnetic as to work in a high temperature up to 1473K. A theoretical expression for the magnetization force, which is indispensable to evaluate the magnetic susceptibility, has been derived. The magnetization forces acting on intermetallic compounds which were used in the magnetic separation were measured over the range of liquidous to solidous temperatures and the magnetic susceptibilities of the intermetallic compounds were obtained from measured magnetization forces by use of the theoretical expression.I. IntroductionRecent developments in the technology of super-conducting magnets have given rise to the circumstance that a high magnetic field over a relatively large space is readily available without liquid helium. Then, it has been found that a high magnetic field provides magnetic effects to nonmagnetic substances and various interesting phenomena have been reported in the broad science fields of physics, chemistry and biology1). ""A science related to a high magnetic field"" in which many fields are transversally viewed from the standpoint of a high magnetic field2 ) is going to be established. In particular, new phenomena and functions brought by the science related to a high magnetic field are also useful for Material Science and Engineering so that the creation of Materials Science and Engineering related to a high magnetic field"" has been conceived 3).Now, when a substance regardless of being magnetic or nonmagnetic is put in a magnetic field, it feels a magnetization force, which is familiar to such a force that a magnet attracts iron. The force is in proportion to the product of magnetic field strength, its gradient and susceptibility so that a precipitated substance can be separated from a molten metal based on the difference between susceptibilities of a substance and a melt. This is a basic principle of the magnetic separation. So far the application of the magnetic separation has been limited to the separation of ferromagnetic substances from a nonmagnetic medium. A high magnetic field, however, has enabled to separate nonmagnetic substances from a nonmagnetic medium.In this study, a new method to separate inclusions from a molten metal using a high magnetic field has been proposed. The principle of the method was verified by experimental works and the feasibility on the elimination of inclusions in steelmaking processes has been studied"

Jan 1, 2000

By B. C. F1intoff, R. G. Bradburn, E. Groiss

"The concentrator at Brenda Mines Ltd. treats a copper - molybdenum porphyry ore with current head grades of 0.185% Cu and 0.036% Mo. The consistently low head grades provided the driving force to explore methods of improving plant productivity. Computer based process control was recognized as one means of addressing this objective. Over the period from 1974 to 1982 a control system evolved which now extends to every area of the mill. Control strategies are built on elements of classical, modern and rudimentary expert control. In addition, the control system has often served as a catalyst for other technological developments. The economic returns associated with the system are very significant and it has played an important role in the mine's survival in times of poor metal markets. This paper presents an overview of the computer control system at Brenda.PreambleOne can scarcely avoid picking up a trade magazine or newspaper today without seeing some reference to technology and its potential impact on North American business. _A recurring theme is the need to apply technology to raise our standard of plant automation in the manufacturing and process industries. The general thesis of these articles has been concisely captured in the mutually exclusive set:AUTOMATE or EMIGRATE or EVAPORATEProcess control is one form of automation that has been successfully exploited by various sectors of these industries. In minerals and metal processing the wide scale adoption of process control technology has, until recently, been largely limited to a few companies - most of whom have a history in the area dating back to the early 1970’s. However, there is definitely an increased and much broader interest in process control as a technology which can improve performance, productivity and profit.The economic hardships that were visited on the mining industry in the early 1980's are not easily forgotten. It is the authors' conviction that the mining industry must move to implement proven technology, in particular process control, in order to be well postured for the next (inevitable) down cycle.In pursuing the technical and trade literature, one can discover a number of example of the successful utilization of process control systems in mining and related applications. In the text which follows, the authors describe the process control efforts undertaken in the Brenda Mines Ltd. concentrator."

Jan 1, 1989

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By J. M. Figueiredo, A. R. Silva, M. C. Coelho, R. M. Guedes

"With the continuous depletion of conventional sources of non ferrous metals, low grade complex sulphide deposits have been regarded as an alternative source of supply of zinc, copper, lead and also silver and gold. In spite of very important efforts in research in this domain it is still a long way to go in order to achieve reliable technological solutions both in ore dressing and metallurgical treatments which enable these complex materials to be regarded as commodities. The RLE process to treat bulk concentrates such as those obtained from portuguese ores, under development at LNETI and QUIMIGAL premises, combines experienced unit operations and innovative configurations and is an effective contribution for the future use of these materials. The results of three years of experimental work and main conclusions on the overall feasibility of the process are presented.IntroductionIn spite of the very well-known problems associated to the development of complex sulphide deposits, the economical importance of the enormous reserves of these materials, widespread all over the world, is so evident that its future use as source of supply of basic and precious metals and other minor elements is almost unavoidable.Critical steps in that direction are mainly concerned with favourable economical conditions and sound metallurgical practice for the treatment of nonferrous metals concentrates, which are nowadays still considered as non-conventional raw materials.Since Portugal is one of the countries where these orebodies occur more extensively, Portuguese authorities have dedicated since the beginning of the seventies, a big effort on finding economical and reliable processes for the recovery of copper, lead, zinc and also gold and silver, and for this purpose, several alternatives on ore dressing and metallurgical processing were studied, however without full sucess.Five years ago LNETI, a research laboratory, and QUIMIGAL, a chemical company, both state owned, decided to launch a research programme for the development of a metallurgical process for the treatment of NFM concentrates, which received financial support from NATO under its programme ""Science for Stability""."

Jan 1, 1988

By J. Avraamides

Some operational difficulties have been encountered in the transfer of carbon-in-pulp technology to Australian conditions. Many gold mines? are located in remote and arid areas where the available ground water is highly saline. There is a gradual depletion of free milling oxidised gold ore reserves resulting in the necessity to treat deeper primary sulphide .deposits which can be refractory. Some near-surface ore-bodies and tailing dumps are contaminated by natural vegetative matter which can interfere with the adsorption of gold from the cyanided pulp,. Advances which have been? made include potable water conservation in elution, a new type of regeneration kiln, inter-stage screens, alternative leaching systems transportable carbon-in-pulp plants and efficient open-cut mining methods. Academic and applied research is well supported by government and industry and the results are normally rapidly disseminated and put into practice by the gold mining industry.

Jan 1, 1989

By Suswnu Makino

Sumitomo Metal Mining developed a new nickel refining process ( Matte Chlorine Leach Electrowinning process) based on chlorine leach and electrowinning technologies. After the pilot plant study, the commercial plant with design capacity of 24,000 tonnes per year was constructed and has been successfully operated since August, 1992. During the practice of the past three years, great deals of improvement have been achieved. Through these operations the MCLE process has been demonstrated to be one of the most superior processes in the world with nickel recovery, productivity, cathode quality and working environment. Today the refinery product capacity is increased to 30,000 tonnes per year. This paper describes the equipments and operation of the Sumitomo MCLE process.

Jan 1, 1996

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the process, to the subsequent cleaning of the gas. and to the use of the heat extracted from the gas. The method of reducing the effect of acidic sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms?are discussed. The development of indirect recuperators using air, water or steam cooling, made possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process? conditions".

Jan 1, 1992

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By Zhiqian Zhang, Chao Wu, Chao Li, Hongxu Li, Yu Chen, Xiangxin Hao

"In this paper, the life cycle assessment models for automobile lightweight materials including high-strength steel, aluminum alloy and magnesium alloy are developed by Gabi software. The evaluation models and evaluation indicators such as acidification effects, rich eutrophication effect, ozone layer depletion effects, global warming, resource consumption and formation of ozone potential were taken into account. It is shown that the effects of acidification and ozone formation are mainly derived from the run phase of high-strength steel and they have strong environmental impact load. While considering the entire life cycle with materials production phase and resource consumption, the aluminum and magnesium alloy appe art o have large r environmental load than high-strength steel. Base d on the evaluation, some optimization tips are proposed.IntroductionAs the increasing of car ownership, automobile has its two sides. One which is the convenient, efficient and fast traffic vehicle; the other is aggravating energy consumption, emissions and environmental pollution. The car industry faces heavy pressure with energy saving, safety and environmental protection. Nowadays, the main study ways for automotive energy-saving and environmental protection are power system improvement, alternative energy sources and technologies. For limitation of technique, development cycle and market share, the development of car is little progress at this stage and the application has been restricted. And another important way is the lightweight of vehicle. Usually there are three ways to get the lightweight automobile body structure, automobile body structure optimized design, using advanced body manufacturing technology, development and application of lightweight high strength body material.The life cycle assessment (LCA)[1lis commonly used to evaluate environmental factors and potential environmental impacts of products and services. As an environmental management tool of product-oriented, it becomes increasingly popular in industry. In this study, the concept of LCA and GaBi software was used to develop models for the three automotive lightweight materials, evaluate the environmental impact and make horizontal and vertical contrast by choosing variety of evaluation systems and indexes."

Jan 1, 2013

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and&apos; control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991